2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
  1. for Standard:
    Remove the front fender splash shield (Click here).

  1. w/ Winch:
    Remove the front fender splash shield (Click here).


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. for Standard:
    Remove the front fender splash shield (Click here).

  1. w/ Winch:
    Remove the front fender splash shield (Click here).


4. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and under cover.


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator reservoir cap to drain the coolant in the radiator.

  1. Loosen the oil filter bracket drain cock plug to drain the coolant in the engine.

    A174741E01

  1. Tighten the radiator drain cock plug by hand.

  1. A177208
    Tighten the oil filter bracket drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


6. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. Remove the 7 clips and radiator support seal.

    B180890E02


7. REMOVE NO. 3 ENGINE ROOM WIRE
  1. Disconnect the 4 wire harness clamps.

  1. Remove the 2 nuts and No. 3 engine room wire.

    A174837


8. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A174701
    Remove the 2 nuts and No. 1 engine cover.


9. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A174698
    Loosen the hose clamp and disconnect the connector.

  1. Using a clip remover, detach the 3 clamps and remove the air cleaner cap.


10. REMOVE NO. 1 AIR CLEANER HOSE

  1. A174699
    Loosen the hose clamp and remove the No. 1 air cleaner hose.


11. REMOVE INTAKE AIR CONNECTOR

A174749E02
  1. Disconnect the 2 connectors from the viscous heater and water temperature sensor.

  1. Using a clip remover, detach the 3 wire harness clamps.

  1. A174710
    Loosen the 2 hose clamps and remove the 2 bolts and intake air connector.


12. REMOVE V-RIBBED BELT

  1. A174847
    Loosen the lock nut and turn the bolt counterclockwise.

  1. Remove the V-ribbed belt.


13. REMOVE VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A177428
    Insert a screwdriver between the reservoir and oil reservoir bracket, push the claw, and then disconnect the reservoir by pulling it upwards.


14. REMOVE VANE PUMP ASSEMBLY

  1. C172309
    Remove the 2 nuts and vane pump.

  1. Remove the O-ring from the vane pump.


15. REMOVE NO. 1 RADIATOR HOSE

16. REMOVE NO. 2 RADIATOR HOSE

17. REMOVE OIL COOLER HOSE (w/ Air Cooled Transmission Oil Cooler)

  1. C167861
    Disconnect the inlet and outlet No. 1 oil cooler hose.

  1. C175574
    Disconnect the inlet No. 2 and No. 3 oil cooler hoses.

  1. C175575
    Disconnect the inlet No. 4 oil cooler hose.

  1. C167866
    Remove the 2 bolts and transmission oil cooler tube.


18. REMOVE FAN SHROUD WITH FAN

  1. A161930
    Loosen the 4 nuts holding the fluid coupling fan.

  1. A177427
    Remove the 2 bolts holding the fan shroud.

  1. A179253
    Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the fluid coupling fan.


19. REMOVE RADIATOR RESERVE TANK ASSEMBLY

  1. A174735
    Disconnect the 2 hoses.

  1. Remove the 3 bolts and radiator reservoir.


20. REMOVE RADIATOR ASSEMBLY
  1. Remove the radiator assembly (Click here).


21. REMOVE IDLER PULLEY ASSEMBLY

E154424
  1. Remove the 2 bolts and 2 idler pulleys.


22. REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

E154426
  1. Disconnect the connector and detach the clamp.

  1. Using pliers, grip the claws of the clips and slide the 2 clips.

  1. Disconnect the 2 heater hoses.

  1. Remove the 2 bolts and heater assembly.


23. REMOVE IDLER PULLEY BRACKET

E154427
  1. Remove the bolt and bracket.


24. REMOVE IDLER PULLEY BRACKET (for Belt Tension Side)

E154425
  1. Remove the 3 bolts and bracket.

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →