2011-2013 Land Cruiser · Service Manual Suspension

C1792 Height Control Switch Circuit (Test Mode DTC)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This circuit sends a signal to the suspension control ECU in order to adjust the height to the selected height by the height control switch.
DTC Code
Detection Condition
Trouble Area
C1792
The test mode procedure is performed.
  1. Harness or connector
  2. Suspension control switch (Height control switch)
  3. Suspension control ECU

WIRING DIAGRAM

C177058E02

INSPECTION PROCEDURE

NOTICE:
  1. Before performing troubleshooting, inspect the connectors of related circuits.
  2. If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (Click here).


1. READ VALUE USING INTELLIGENT TESTER (HEIGHT CONTROL SWITCH (UP), HEIGHT CONTROL SWITCH (DOWN))
  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and the tester on.

  1. Enter the following menus: Chassis / AHC / Data List.

  1. According to the display on the tester, read the Data List.

    AHC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Height Control Switch(Up)
    Height control switch (Up) /
    ON or OFF
    ON: Up button of the height control switch is pushed.
    OFF: Height control switch is not pushed.
    -
    Height Control Switch(Down)
    Height control switch (Down) /
    ON or OFF
    ON: Down button of the height control switch is pushed.
    OFF: Height control switch is not pushed.
    -

OK:
On the tester screen, item changes between ON and OFF according to switch operation.



NG
Go to step 3
OK


2. TEST MODE INSPECTION
  1. Refer to the Test Mode Procedure and perform the signal check. Check that test mode DTC C1792 is cleared (Click here).

    Result 
    Result
    Proceed to
    DTC C1792 is not cleared
    A
    DTC C1792 is cleared
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE SUSPENSION CONTROL ECU (Click here)

3. INSPECT SUSPENSION CONTROL SWITCH (HEIGHT CONTROL SWITCH)
  1. Remove the suspension control switch (Click here).

  1. C175598E15
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (LO) - 20 (E)
    Down button of the height control switch is pushed.
    Below 1 Ω
    Height control switch is not pushed or the up button is pushed.
    10 kΩ or higher
    7 (HI) - 20 (E)
    Up button of the height control switch is pushed.
    Below 1 Ω
    Height control switch is not pushed or the down button is pushed.
    10 kΩ or higher



NG
REPLACE SUSPENSION CONTROL SWITCH (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - SWITCH AND BODY GROUND)
C177225E02
  1. Disconnect the K34 ECU connector.

  1. Disconnect the V4 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K34-20 (UPSW) - V4-7 (HI)
    Always
    Below 1 Ω
    K34-20 (UPSW) - Body ground
    Always
    10 kΩ or higher
    K34-21 (DNSW) - V4-6 (LO)
    Always
    Below 1 Ω
    K34-21 (DNSW) - Body ground
    Always
    10 kΩ or higher
    V4-20 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← C1791 Absorber Control Switch Circuit (Test Mode DTC) (from Jan 2012)C1792 Height Control Switch Circuit (Test Mode DTC) (from Jan 2012) →