2011-2013 Land Cruiser · Service Manual Vehicle Interior

Cooling Box Control Switch Circuit

Circuit diagnosis · Vehicles built from Sep 2011

DESCRIPTION

The cooler control switch is the activation switch for the cooling box. If the cooling box does not activate when the cooler control switch is pushed, there may be a malfunction in the circuit shown below.

WIRING DIAGRAM

E160130E01

INSPECTION PROCEDURE


1. INSPECT FUSE (PANEL, A/C IG, ECU-B1)
  1. Remove the PANEL and A/C IG fuses from the cowl side junction block LH.

  1. Remove the ECU-B1 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    PANEL fuse
    Always
    Below 1 Ω
    ECU-B1 fuse
    Always
    Below 1 Ω
    A/C IG fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2. CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS - BATTERY)

  1. E158385E18
    Disconnect the No. 1 cooler wiring harness sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    4 (+B) - Body ground
    Always
    11 to 14 V
    1 (B) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (NO. 1 COOLER WIRING HARNESS - BODY GROUND)

  1. E158385E19
    Disconnect the No. 1 cooler wiring harness sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    6 (L) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY (OPERATION)
  1. Replace the No. 1 cooler wiring harness sub-assembly with a normal one and check that the condition returns to normal.

    OK:
    Same problem does not occur.



NG
Go to step 5
OK

REPLACE NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY

5. INSPECT COOLER CONTROL SWITCH SUB-ASSEMBLY

  1. E158415E02
    Remove the cooler control switch sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    On
    Below 1 Ω
    1 - 2
    Off
    10 kΩ or higher

  1. Apply battery voltage to the cooler control switch connector and check that the cooler control switch illuminates.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3
    Battery negative (-) → Terminal 4
    LED illuminates
    Battery positive (+) → Terminal 5
    Battery negative (-) → Terminal 6
    LED illuminates



NG
REPLACE COOLER CONTROL SWITCH SUB-ASSEMBLY (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Cool Box) (Click here)


← Cooling Box Blower Motor Circuit (from Sep 2011)Cooling Box Sensor Circuit (from Sep 2011) →