2011-2013 Land Cruiser · Service Manual Power Source / Network

U0132 Lost Communication with Suspension Control ECU

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
U0132
There is no communication from the suspension control ECU.
  1. Power source circuit of suspension control ECU
  2. Suspension control ECU branch wire or connector
  3. Suspension control ECU
  1. For vehicles with active height control suspension.

WIRING DIAGRAM

C177459E05

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicle with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)

  1. C251314E04
    Disconnect the K34 suspension control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    K34-7 (CANH) - K34-8 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Suspension Control ECU)



NG
REPAIR OR REPLACE SUSPENSION CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


4. CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)

  1. C251478E08
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the K35 suspension control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    K34-3 (BAT2) - Body ground
    Always
    11 to 14 V
    K35-1 (BAT) - Body ground
    Always
    11 to 14 V
    K34-5 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K34-1 (GND) - Body ground
    Always
    Below 1 Ω
    K35-6 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Rear view of wire harness connector
(to Suspension Control ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)


← U0132 Lost Communication with Suspension Control ECU (Sep 2011 – Dec 2011)U0141 Lost Communication with Body Control Module "A" (from Jan 2012) →