P0500 Vehicle Speed Sensor "A"
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0500 |
While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic). |
|
MONITOR DESCRIPTION
The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK OPERATION OF SPEEDOMETER |
Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.
- HINT:
- The vehicle speed sensor is operating normally if the speedometer reading is normal.
- If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).
- The vehicle speed sensor is operating normally if the speedometer reading is normal.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Data List.
Drive the vehicle.
According to the display on the tester, read the Data List.
ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed
The speed is indicated on the speedometer.
- OK:
- Vehicle speeds displayed on intelligent tester and speedometer display are equal.
|
|
||||
| OK | ||
| ||
| 3. CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE) |
![]() ![]() |
Disconnect the E7 combination meter connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E7-4 (+S) - Body ground
Ignition switch ON
4.5 to 5.5 V
|
|
||||
| OK | |
| 4. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM) |
![]() ![]() |
Move the shift lever to N.
Jack up the vehicle.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E7-4 (+S) - Body ground
- Ignition switch ON
- Wheel is turned slowly
Voltage generated intermittently
- Ignition switch ON
- HINT:
- The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
Result Result
Proceed to
OK
A
NG (w/ Multi-information Display)
B
NG (w/o Multi-information Display)
C
|
|
||||
|
|
||||
| A | |
| 5. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM) |
![]() ![]() |
Disconnect the E7 combination meter connector.
Disconnect the A38 ECM connector (for LHD).
Disconnect the A52 ECM connector (for RHD).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
E7-4 (+S) - A38-8 (SPD)
Always
Below 1 Ω
E7-4 (+S) or A38-8 (SPD) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
E7-4 (+S) - A52-8 (SPD)
Always
Below 1 Ω
E7-4 (+S) or A52-8 (SPD) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||



