2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Tail Gate Closer does not Operate

Circuit diagnosis · Vehicles built from Jan 2012

WIRING DIAGRAM

B312263E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (NO. 2 MAIN BODY ECU - BATTERY AND BODY GROUND)
B115211E02
  1. Disconnect the No. 2 main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L51-5 (B) - Body ground
    Always
    11 to 14 V
    L51-6 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L51-7 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to No. 2 Main Body ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT LOWER TAIL GATE LOCK ASSEMBLY
  1. for LH:

    1. Remove the lower tail gate lock assembly LH (Click here).

    2. Inspect the lower tail gate lock assembly LH (Click here).

  1. for RH:

    1. Remove the lower tail gate lock assembly RH (Click here).

    2. Inspect the lower tail gate lock assembly RH (Click here).

Result 
Result
Proceed to
OK
A
NG (for LH)
B
NG (for RH)
C


B
REPLACE LOWER TAIL GATE LOCK ASSEMBLY LH (Click here)

C
REPLACE LOWER TAIL GATE LOCK ASSEMBLY RH (Click here)
A


3. CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY - NO. 2 MAIN BODY ECU)
  1. for LH:

    1. Disconnect the h5 lower tail gate lock assembly LH connector.

    2. Disconnect the L51 No. 2 main body ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      h5-5 (ACT+) - L51-3 (DC+)
      Always
      Below 1 Ω
      h5-6 (ACT-) - L51-8 (DC-)
      Always
      Below 1 Ω
      h5-5 (ACT+) - Body ground
      Always
      10 kΩ or higher
      h5-6 (ACT-) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the h4 lower tail gate lock assembly RH connector.

    2. Disconnect the L51 No. 2 main body ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      h4-5 (ACT+) - L51-2 (DC+)
      Always
      Below 1 Ω
      h4-6 (ACT-) - L51-1 (DC-)
      Always
      Below 1 Ω
      h4-5 (ACT+) - Body ground
      Always
      10 kΩ or higher
      h4-6 (ACT-) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 2 MAIN BODY ECU (Click here)


← B225D Tail Gate Panel Half Switch or Courtesy Switch LH (from Jan 2012)Tail Gate does not Open with Back Door Remote Control (from Jan 2012) →