2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B15D6 Display Disconnected

Diagnostic trouble codes · Vehicles built from Jan 2012

DESCRIPTION

The multi-display assembly and multi-media module receiver assembly are connected by an AVC-LAN communication line.
When an AVC-LAN communication error occurs between the display module board and multi-display assembly, these DTCs will be stored.
DTC Code
DTC Detection Condition
Trouble Area
B15D6*
A device that is listed in the AVC-LAN connected device record of the master unit is missing.
  1. Multi-display assembly
  2. Multi-media module receiver assembly
  3. Harness or connector

HINT:
  1. *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The multi-media module receiver assembly is the master unit.


WIRING DIAGRAM

C260261E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    DTC B15D6 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)

  1. E206146E08
    Disconnect the multi-display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F79-13 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F79-12 (+B2) - F79-13 (GND1)
    Always
    11 to 14 V
    F79-23 (IG) - F79-13 (GND1)
    Engine switch on (IG)
    11 to 14 V
    F79-24 (ACC) - F79-13 (GND1)
    Engine switch on (ACC)
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Multi-display assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

  1. E238990E03
    Remove the multi-media module receiver assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    45 (TX3+) - 46 (TX3-)
    Always
    60 to 80 Ω



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
  1. Disconnect the F77 multi-media module receiver assembly connector.

  1. Disconnect the F79 multi-display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F77-45 (TX3+) - F79-7 (TX+)
    Always
    Below 1 Ω
    F77-46 (TX3-) - F79-19 (TX-)
    Always
    Below 1 Ω
    F77-45 (TX3+) - Body ground
    Always
    10 kΩ or higher
    F77-46 (TX3-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE MULTI-DISPLAY ASSEMBLY
  1. Replace the multi-display assembly with a new or normally functioning one (Click here).


NEXT


7. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


8. CHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    DTC B15D6 is not output.



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)


← B15D3 Stereo Component Amplifier Disconnected (from Jan 2012)B15DF USB Communication Malfunction (Sep 2011 – Dec 2011) →