B15D3 Stereo Component Amplifier Disconnected
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
The multi-media module receiver assembly, television display assembly* and stereo component amplifier assembly are connected by the MOST network.When a MOST network error occurs between the multi-media module receiver assembly, television display assembly and stereo component amplifier assembly, these DTCs will be stored.
- *: w/ Rear Seat Entertainment System
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B15D3 |
A device that is listed in the MOST network connected device record of the master unit is missing. |
|
- *: w/ Rear Seat Entertainment System
- HINT:
- For the MOST network, the multi-media module receiver assembly is the master unit.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) |
Check for optional components.
Check that optional components (including associated wiring) which generate radio waves are not installed.
Result Result
Proceed to
Optional components (including associated wiring) are installed.
A
Optional components (including associated wiring) are not installed.
B
- HINT:
- Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.
- This DTC may be stored when a MOST communication error occurs due to electrical noise.
- Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.
|
|
||||
| A | |
| 2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) |
Remove optional components (including associated wiring).
- NOTICE:
- Do not remove optional components or associated wiring without the permission of the customer.
| NEXT | |
| 3. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 4. CHECK DTC |
Recheck for DTCs and check if the same DTCs are output again (Click here).
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND) |
Disconnect the stereo component amplifier assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F74-3 (GND) - Body ground
Always
Below 1 Ω
F74-18 (GND2) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
F74-1 (+B) - F74-3 (GND)
Always
11 to 14 V
F74-16 (+B2) - F74-3 (GND)
Always
11 to 14 V
| *a |
Front view of wire harness connector (to Stereo Component Amplifier Assembly) |
| Result |
Proceed to |
| OK (w/o Rear Seat Entertainment System) |
A |
| OK (w/ Rear Seat Entertainment System) |
B |
| NG |
C |
|
|
||||
|
|
||||
| A | |
| 6. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY) |
Disconnect the F84 multi-media module receiver assembly connector.
Disconnect the F85 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F84-2 (MI+) - F85-5 (MO+)
Always
Below 1 Ω
F84-3 (MI-) - F85-6 (MO-)
Always
Below 1 Ω
F84-4 (SLDI) - F85-7 (SLDO)
Always
Below 1 Ω
F84-5 (MO+) - F84-2 (MI+)
Always
Below 1 Ω
F84-6 (MO-) - F85-3 (MI-)
Always
Below 1 Ω
F84-7 (SLDO) - F85-4 (SLDI)
Always
Below 1 Ω
F84-2 (MI+) - Body ground
Always
10 kΩ or higher
F84-3 (MI-) - Body ground
Always
10 kΩ or higher
F84-4 (SLDI) - Body ground
Always
10 kΩ or higher
F84-5 (MO+) - Body ground
Always
10 kΩ or higher
F84-6 (MO-) - Body ground
Always
10 kΩ or higher
F84-7 (SLDO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY |
Replace the stereo component amplifier assembly with a new or normally functioning one (Click here).
| NEXT | |
| 8. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 9. CHECK DTC |
Recheck for DTCs and check if the same DTC is output again (Click here).
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
| 10. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - MULTI-MEDIA MODULE RECEIVER AND TELEVISION DISPLAY) |
Disconnect the F84 multi-media module receiver assembly connector.
Disconnect the F85 stereo component amplifier assembly connector.
Disconnect the L56 television display assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F84-5 (MO+) - F85-2 (MI+)
Always
Below 1 Ω
F84-6 (MO-) - F85-3 (MI-)
Always
Below 1 Ω
F84-7 (SLDO) - F85-4 (SLDI)
Always
Below 1 Ω
F85-5 (MO+) - L56-2 (MI+)
Always
Below 1 Ω
F85-6 (MO-) - L56-3 (MI-)
Always
Below 1 Ω
F85-7 (SLDO) - L56-4 (SLDI)
Always
Below 1 Ω
F85-2 (MI+) - Body ground
Always
10 kΩ or higher
F85-3 (MI-) - Body ground
Always
10 kΩ or higher
F85-4 (SLDI) - Body ground
Always
10 kΩ or higher
F85-5 (MO+) - Body ground
Always
10 kΩ or higher
F85-6 (MO-) - Body ground
Always
10 kΩ or higher
F85-7 (SLDO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 11. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY |
Replace the stereo component amplifier assembly with a new or normally functioning one (Click here).
| NEXT | |
| 12. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 13. CHECK DTC |
Recheck for DTCs and check if the same DTC is output again (Click here).
|
|
||||
| OK | ||
| ||
| 14. REPLACE TELEVISION DISPLAY ASSEMBLY |
Replace the television display assembly with a new or normally functioning one (Click here).
| NEXT | |
| 15. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 16. CHECK DTC |
Recheck for DTCs and check if the same DTC is output again (Click here).
|
|
||||
| OK | ||
| ||
