2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B1569 DVD-ROM Deck Disconnected

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The display and navigation module display and navigation module board are connected by the IEEE cable.
When an IEEE communication error occurs between the display and navigation module display and navigation module board, this DTC will be stored.
DTC No.
DTC Detection Condition
Trouble Area
B1569
When either of the conditions below is met:
  1. Navigation module board is/was not connected while the engine switch is on (IG or ACC).
  2. Communication between the master unit and navigation module board is not possible when the engine is started.
  1. Navigation module board power source circuit
  2. IEEE cable
  3. Display and navigation module display
  4. Navigation module board

HINT:
  1. Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The display and navigation module display is the master unit.


WIRING DIAGRAM

E189963E03

INSPECTION PROCEDURE


1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components.

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result 
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect IEEE communication.
      2. This DTC may be stored when an IEEE communication error occurs due to electrical noise.



B
Go to step 3
A


2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

END

4. CHECK HARNESS AND CONNECTOR (NAVIGATION MODULE BOARD POWER SOURCE)

  1. E194863E02
    Disconnect the F68 navigation module board connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F68-5 (G) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F68-1 (+B) - F68-5 (G)
    Always
    11 to 14 V
    F68-3 (ACC) - F68-5 (G)
    Engine switch on (ACC)
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Navigation Module Board)



NG
Go to step 8
OK


5. CHECK IEEE CABLE CONNECTOR
  1. Check for the IEEE cable connector.

    1. Check if the IEEE cable connectors between the navigation module board and the display and navigation module display have any connection problems (Click here).

  1. Check that the screen display is normal.

    OK:
    Screen display is normal.



NG
Go to step 6
OK

END

6. REPLACE IEEE CABLE
  1. Replace the IEEE cable between the navigation module board and the display and navigation module display.

  1. Check that the screen display is normal.

    OK:
    Screen display is normal.



NG
Go to step 7
OK

END

7. REPLACE NAVIGATION MODULE BOARD
  1. Replace the navigation module board (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)
OK

END

8. CHECK HARNESS AND CONNECTOR (DISPLAY AND NAVIGATION MODULE DISPLAY - NAVIGATION MODULE BOARD)
  1. Disconnect the F67 display and navigation module display connector.

  1. Disconnect the F68 navigation module board connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F67-1 (+B2) - F68-1 (+B)
    Always
    Below 1 Ω
    F67-2 (ACC2) - F68-3 (ACC)
    Always
    Below 1 Ω
    F67-4 (G) - F68-5 (G)
    Always
    Below 1 Ω
    F67-1 (+B2) - Body ground
    Always
    10 kΩ or higher
    F67-2 (ACC2) - Body ground
    Always
    10 kΩ or higher
    F67-4 (G) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (Sep 2011 – Dec 2011)B156B Multi-media Interface ECU Disconnected (+ B156E) (Sep 2011 – Dec 2011) →