2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B156B Multi-media Interface ECU Disconnected

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The display and navigation module display and multi-media interface ECU are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the display and navigation module display and the multi-media interface ECU, these DTCs will be stored.
DTC No.
DTC Detection Condition
Trouble Area
B156B*1
When either condition below is met:
  1. Multi-media interface ECU is/was not connected while the engine switch is on (ON or ACC).
  2. Communication between the master unit and multi-media interface ECU is not possible when the engine is started.
  1. Multi-media interface ECU power source circuit
  2. AVC-LAN circuit between display and navigation module display and multi-media interface ECU
  3. Multi-media interface ECU
  4. Display and navigation module display
B156E
Within the time-out period, there was no response from the display and navigation module display to the following requests from the master unit:
  1. System inspection request
  2. System inspection result request
  3. Diagnostic memory request

HINT:
  1. *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The display and navigation module display is the master unit.


WIRING DIAGRAM

E184614E08

INSPECTION PROCEDURE


1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components.

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result 
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
      2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 3
A


2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

END

4. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU POWER SOURCE)

  1. E191384E02
    Disconnect the L41 multi-media interface ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L41-7 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L41-12 (+B) - L41-7 (GND)
    Always
    11 to 14 V
    L41-11 (ACC) - L41-7 (GND)
    Engine switch on (ACC)
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Multi-media Interface ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU - DISPLAY AND NAVIGATION MODULE)
  1. Disconnect the L41 multi-media interface ECU connector.

  1. Disconnect the F60 display and navigation module display connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L41-9 (TX1+) - F60-9 (TX2+)
    Always
    Below 1 Ω
    L41-10 (TX1-) - F60-10 (TX2-)
    Always
    Below 1 Ω
    L41-9 (TX1+) - Body ground
    Always
    10 kΩ or higher
    L41-10 (TX1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE MULTI-MEDIA INTERFACE ECU
  1. Replace the multi-media interface ECU (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)
OK

END


← B1569 DVD-ROM Deck Disconnected (Sep 2011 – Dec 2011)B1582 Map Disk Reading Malfunction (Sep 2011 – Dec 2011) →