2011-2013 Land Cruiser · Service Manual Brake

Brake Warning Light Remains ON

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The brake warning light comes on when brake fluid is insufficient, the parking brake is applied or the EBD is defective.

WIRING DIAGRAM

C258218E01

INSPECTION PROCEDURE

NOTICE:
After replacing the master cylinder solenoid, perform calibration (Click here).


1. CHECK DTC
  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus.

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


3. READ VALUE USING GTS (PARKING BRAKE SW)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch/ ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using the GTS, check the input of the switch operation when the parking brake pedal is operated.

    OK:
    When the parking brake is operated, the display changes as shown above.



NG
Go to step 5
OK


4. PERFORM ACTIVE TEST USING GTS (BRAKE WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Brake Warning Light
    Brake warning light
    Warning light ON/OFF
    Observe the combination meter.

  1. When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Brake Warning Light
    Brake warning light/ ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -
    Result 
    Result
    Proceed to
    Data List Display
    Data List Display when Performing Active Test ON/OFF Operation
    ON
    Changes between ON and OFF
    A
    Does not change between ON and OFF (for LHD)
    B
    Does not change between ON and OFF (for RHD)
    C
    OFF
    Changes between ON and OFF
    A
    Does not change between ON and OFF (for LHD)
    B
    Does not change between ON and OFF (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

5. INSPECT PARKING BRAKE SWITCH
  1. Disconnect the E53 parking brake switch connector.

  1. C215408E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake applied
    (Switch pin not pushed in)
    Below 1 Ω
    Parking brake released
    (Switch pin pushed in)
    10 kΩ or higher

    Text in Illustration  
    *a
    Component without harness connected
    (Parking Brake Switch)



NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU)
  1. Disconnect the E53 parking brake switch connector.

  1. Disconnect the 2D main body ECU (cowl side junction block LH).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E53-1 - 2D-22
    Always
    Below 1 Ω
    E53-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


← Brake Warning Light Remains ON (Sep 2011 – Dec 2011)Brake Warning Light does not Come ON (Sep 2011 – Dec 2011) →