2011-2013 Land Cruiser · Service Manual Brake

Turn Assist Indicator Light Circuit

Circuit diagnosis · Vehicles built from Jan 2012

DESCRIPTION

When any of the following conditions are met, the turn assist system becomes operable and the turn assist indicator light illuminates.
  1. Crawl Control is operating.
  2. The turn assist function switch (suspension control switch) is on.
  3. The center differential is "free".
  4. The vehicle is moving at a speed of 10 km/h (6 mph) or less.
  5. The shift lever is not in P, R or N.

WIRING DIAGRAM

C256733E03

INSPECTION PROCEDURE

NOTICE:
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (Click here).


1. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and the GTS on.

  1. Select "CAN Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.

    OK:
    "CAN Bus Check" indicates no malfunctions in CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and the GTS on.

  1. Check for DTCs (for LHD: Click here, for RHD: Click here).

    Result 
    Result
    Proceed to
    CAN system DTC is not output
    A
    CAN system DTC is output (for LHD)
    B
    CAN system DTC is output (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


3. INSPECT TURN ASSIST FUNCTION SWITCH
  1. Remove the turn assist function switch (suspension control switch) (Click here).

  1. Inspect the turn assist function switch (suspension control switch) (Click here).



NG
REPLACE SUSPENSION CONTROL SWITCH (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TURN ASSIST FUNCTION SWITCH)
  1. Turn the ignition switch off.

  1. Disconnect the A24 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the V4 turn assist function switch (suspension control switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-29 (EXI4) - V4-2 (OTA)
    Always
    Below 1 Ω
    A24-29 (EXI4) - Body ground
    Always
    10 kΩ or higher
    V4-16 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI4 CIRCUIT)
  1. Turn the ignition switch off.

  1. Connect the skid control ECU (master cylinder solenoid) connector.

  1. E133658E10
    Disconnect the turn assist function switch (suspension control switch) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    V4-2 (OTA) - Body ground
    Ignition switch ON
    11 to 14 V

    *a
    Front view of wire harness connector
    (to Turn Assist Function Switch [Suspension Control Switch])
    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)


← Slip Indicator Light does not Come ON (from Jan 2012)Skid Control Buzzer Circuit (Sep 2011 – Dec 2011) →