2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B15D8 Monitor Disconnected

Diagnostic trouble codes · Vehicles built from Jan 2012

DESCRIPTION

The parking assist ECU and multi-media module receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the multi-media module receiver assembly and parking assist ECU, these DTCs will be stored.
DTC Code
DTC Detection Condition
Trouble Area
B15D8*
A device that is listed in the AVC-LAN connected device record of the master unit is missing.
  1. Parking assist ECU power source circuit
  2. AVC-LAN circuit
  3. Parking assist ECU
  4. Multi-media module receiver assembly

HINT:
  1. *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The multi-media module receiver assembly is the master unit.


WIRING DIAGRAM

E245658E05

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)

  1. E245332E09
    Disconnect the parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F75-4 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F75-1 (+B) - F75-4 (GND1)
    Always
    11 to 14 V
    F75-8 (IG) - F75-4 (GND1)
    Engine switch on (IG)
    11 to 14 V
    F75-9 (ACC) - F75-4 (GND1)
    Engine switch on (ACC)
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Parking Assist ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY

  1. E238990E09
    Remove the multi-media module receiver assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    7 (TX1+) - 8 (TX1-)
    Always
    60 to 80 Ω



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - PARKING ASSIST ECU)
  1. Disconnect the F77 multi-media module receiver assembly connector.

  1. Disconnect the F75 parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F77-7 (TX1+) - F75-11 (TX+)
    Always
    Below 1 Ω
    F77-8 (TX1-) - F75-10 (TX-)
    Always
    Below 1 Ω
    F77-7 (TX1+) - Body ground
    Always
    10 kΩ or higher
    F77-8 (TX1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE PARKING ASSIST ECU
  1. Replace the parking assist ECU with a new or normally functioning one (Click here).


NEXT


7. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


8. CHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK

END (PARKING ASSIST ECU IS DEFECTIVE)


← B15D6 Display Disconnected (from Jan 2012)B15E5 Electric Throttle Malfunction (from Jan 2012) →