B15D6 Display Disconnected
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
The multi-display assembly and multi-media module receiver assembly are connected by an AVC-LAN communication line.When an AVC-LAN communication error occurs between the multi-media module receiver assembly and multi-display assembly, these DTCs will be stored.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B15D6* |
A device that is listed in the AVC-LAN connected device record of the master unit is missing. |
|
- HINT:
- *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
- The multi-media module receiver assembly is the master unit.
- *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2. CHECK DTC |
Recheck for DTCs and check if the same DTC is output again (Click here).
- OK:
- No DTCs are output
|
|
||||
| OK | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND) |
Disconnect the multi-display assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F79-13 (GND1) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
F79-12 (+B2) - F79-13 (GND1)
Always
11 to 14 V
F79-23 (IG) - F79-13 (GND1)
Engine switch on (IG)
11 to 14 V
F79-24 (ACC) - F79-13 (GND1)
Engine switch on (ACC)
11 to 14 V
| *a |
Front view of wire harness connector (to Multi-display Assembly) |
|
|
||||
| OK | |
| 4. INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY |
Remove the multi-media module receiver assembly (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
45 (TX3+) - 46 (TX3-)
Always
60 to 80 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY) |
Disconnect the F77 multi-media module receiver assembly connector.
Disconnect the F79 multi-display assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F77-45 (TX3+) - F79-7 (TX+)
Always
Below 1 Ω
F77-46 (TX3-) - F79-19 (TX-)
Always
Below 1 Ω
F77-45 (TX3+) - Body ground
Always
10 kΩ or higher
F77-46 (TX3-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. REPLACE MULTI-DISPLAY ASSEMBLY |
Replace the multi-display assembly with a new or normally functioning one (Click here).
| NEXT | |
| 7. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 8. CHECK DTC |
Recheck for DTCs and check if the same DTC is output again (Click here).
- OK:
- No DTCs are output
|
|
||||
| OK | ||
| ||
