Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › POWER STEERING OIL PRESSURE SWITCH
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254981 POWER STEERING OIL PRESSURE SWITCH A

1UR-FE ENGINE CONTROL  POWER STEERING OIL PRESSURE SWITCH  INSTALLATION  


PROCEDURE

Hide 89438A 1.INSTALL POWER STEERING OIL PRESSURE SWITCH

a.

Install a new O-ring to the power steering oil pressure switch.


b.

Apply a light coat of power steering fluid to the O-ring.


c.

Using a 24 mm deep socket wrench, install the power steering oil pressure switch.

Torque:
21 N*m (210 kgf*cm, 15 ft.*lbf)


d.

Connect the power steering oil pressure switch connector.


Hide 89405B 2.INSTALL FRONT HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH (w/ Active Height Control)

a.

Install the front height control sensor sub-assembly RH with the bolt and nut.

Torque:
for bolt : 13 N*m (127 kgf*cm, 9 ft.*lbf)
for nut : 5.6 N*m (57 kgf*cm, 50 in.*lbf)


b.

Connect the connector.


Hide 3.ADD POWER STEERING FLUID

Hide 4.BLEED POWER STEERING SYSTEM

a.

Check the fluid level.


b.

Jack up the front of the vehicle and support it with stands.


c.

Turn the steering wheel.

i.

With the engine stopped, turn the wheel slowly from lock to lock several times.



d.

Lower the vehicle.


e.

Start the engine.


f.

Idle the engine for a few minutes.


g.

Turn the steering wheel.

i.

With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds. *1


ii.

Repeat *1 several times.

NOTICE:

For vehicles with VGRS, if the steering wheel is turned from lock to lock repeatedly, the system may stop operating and the amount of rotation before the steering wheel locks may increase due to operation of the overheating prevention function. When the system temperature drops, the system operation automatically returns to normal.




h.

Stop the engine.


i.
C124274E03
0.574,0.312 1.303,0.462 0.730,0.150 10 *a 1.919,0.312 2.841,0.462 0.922,0.150 10 *b

Check for foaming or emulsification.

Text in Illustration
*a Correct
*b Incorrect

If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.


j.

Check the fluid level.


Hide 5.INSPECT FOR POWER STEERING FLUID LEAK

Hide 6.CHECK POWER STEERING FLUID LEVEL

a.
C158723E02
0.478,0.875 0.653,1.056 0.174,0.180 10 *a 2.794,0.751 2.968,0.917 0.174,0.166 10 *b

Keep the vehicle horizontal.

Text in Illustration
*a COLD Range
*b HOT Range


b.

With the engine stopped, check the fluid level in the reservoir.

If necessary, add fluid.

Fluid:

ATF DEXRON II or III, or equivalent


HINT:

If the fluid is hot, check that the fluid level is within the HOT range. If the fluid is cold, check that the fluid level is within the COLD range.



c.

Start the engine and idle it.


d.

Turn the steering wheel from lock to lock several times to raise the fluid temperature.

Fluid temperature:

80°C (176°F)



e.
C124274E03
0.574,0.312 1.303,0.462 0.730,0.150 10 *a 1.919,0.312 2.841,0.462 0.922,0.150 10 *b

Check for foaming or emulsification.

Text in Illustration
*a Correct
*b Incorrect

If foaming or emulsification is identified, bleed the power steering system.


f.
U153404E01
0.858,1.589 1.046,1.739 0.187,0.150 10 *a 1.632,1.368 1.825,1.530 0.192,0.162 10 *c 2.356,1.589 2.533,1.739 0.177,0.150 10 *b 1.437,0.986 1.835,0.986 false 1.591,0.909 2.006,0.909 false 1.718,0.808 1.718,0.545 false 1.726,1.092 1.726,1.355 false

With the engine idling, measure the fluid level in the reservoir.

Text in Illustration
*a Engine idling
*b Engine stopped
*c 5.0 mm (0.197 in.) or less


g.

Stop the engine.


h.

Wait a few minutes and remeasure the fluid level in the reservoir.

Maximum fluid level rise:

5.0 mm (0.197 in.)


If the fluid level rise is more than the maximum, bleed the power steering system.


i.

Check the fluid level.


Hide 53782 7.INSTALL FRONT FENDER APRON TRIM PACKING A