Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM J

1UR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil of the No. 1 integration relay (EFI relay), closing the contacts and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

U163732E01
0.597,3.891 1.079,4.076 0.482,0.185 10 Battery 3.229,0.414 3.591,0.608 0.362,0.193 10 IG2D 3.656,0.306 3.864,0.483 0.208,0.177 10 11 2.384,0.815 2.675,0.978 0.291,0.163 10 E2 2.384,0.962 3.455,1.125 1.071,0.163 10 Main Body ECU 1.538,3.333 1.665,3.510 0.127,0.177 10 3 1.489,3.494 1.702,3.656 0.212,0.162 10 1B 2.129,4.241 3.640,4.432 1.511,0.191 10 No. 1 Integration Relay 1.538,1.735 1.665,1.912 0.127,0.177 10 1 2.348,1.754 2.475,1.931 0.127,0.177 10 1 2.608,1.754 2.735,1.931 0.127,0.177 10 2 2.348,2.983 2.475,3.160 0.127,0.177 10 1 2.608,2.983 2.735,3.160 0.127,0.177 10 2 1.489,1.896 1.702,2.058 0.212,0.162 10 1C 4.168,3.325 4.295,3.502 0.127,0.177 10 2 4.12,3.49 4.333,3.652 0.212,0.162 10 1B 4.168,2.955 4.295,3.132 0.127,0.177 10 4 4.12,3.115 4.333,3.277 0.212,0.162 10 1B 4.168,2.109 4.295,2.286 0.127,0.177 10 6 4.12,2.27 4.333,2.432 0.212,0.162 10 1B 4.168,2.496 4.295,2.673 0.127,0.177 10 7 4.12,2.656 4.333,2.818 0.212,0.162 10 1B 4.168,1.731 4.295,1.908 0.127,0.177 10 8 4.12,1.895 4.333,2.058 0.212,0.162 10 1B 5.672,1.735 6.000,1.912 0.328,0.177 10 28*2 5.692,1.895 5.972,2.058 0.280,0.162 10 A38 2.253,3.27 2.940,3.450 0.687,0.180 10 EFI MAIN 3.502,3.821 3.795,3.988 0.293,0.167 10 EFI 3.513,1.58 3.806,1.747 0.293,0.167 10 IG2 2.248,2.045 2.892,2.213 0.644,0.168 10 IG2 MAIN 4.741,1.752 4.868,1.929 0.127,0.177 10 1 4.997,1.752 5.124,1.929 0.127,0.177 10 2 4.788,2.017 5.093,2.186 0.304,0.168 10 IGN 6.036,1.791 6.451,1.954 0.415,0.163 10 IGSW 5.715,2.592 5.968,2.768 0.253,0.177 10 3*2 5.692,2.752 5.972,2.914 0.280,0.162 10 A38 6.036,2.751 6.255,2.914 0.219,0.163 10 +B 5.715,2.942 5.968,3.118 0.253,0.177 10 2*2 5.692,3.102 5.972,3.264 0.280,0.162 10 A38 6.036,3.101 6.352,3.264 0.316,0.163 10 +B2 5.667,3.32 5.978,3.497 0.311,0.177 10 34*2 5.692,3.484 5.972,3.647 0.280,0.162 10 A38 6.036,3.48 6.443,3.642 0.407,0.163 10 MREL 5.667,3.862 6.002,4.039 0.334,0.177 10 81*2 5.692,4.023 5.972,4.185 0.280,0.162 10 C45 6.036,4.022 6.290,4.185 0.254,0.163 10 E1 6.359,4.551 6.716,4.702 0.357,0.151 10 ECM 5.345,1.735 5.650,1.912 0.305,0.177 10 28*1 5.365,1.895 5.645,2.058 0.280,0.162 10 A52 5.388,2.592 5.631,2.768 0.244,0.177 10 3*1 5.365,2.752 5.645,2.914 0.280,0.162 10 A52 5.388,2.942 5.622,3.118 0.235,0.177 10 2*1 5.365,3.102 5.645,3.264 0.280,0.162 10 A52 5.34,3.32 5.665,3.497 0.325,0.177 10 34*1 5.365,3.484 5.645,3.647 0.280,0.162 10 A52 5.34,3.862 5.647,4.039 0.306,0.177 10 81*1 5.365,4.023 5.645,4.185 0.280,0.162 10 C46 3.872,4.477 4.620,4.633 0.748,0.156 10 *1: for RHD 3.872,4.731 4.620,4.887 0.748,0.156 10 *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK NO. 1 INTEGRATION RELAY (POWER SOURCE)
U163264E01
0.163,0.038 0.368,0.243 0.205,0.205 10 *a 2.741,0.984 2.967,1.167 0.225,0.184 10 1C 2.097,2.032 2.267,2.202 0.170,0.170 10 *1 1.517,2.696 2.065,2.133 false 2.839,1.582 2.938,1.715 0.099,0.133 8 1

a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V


Text in Illustration
*1 No. 1 Integration relay
*a Front view of wire harness connector
(to No. 1 Integration Relay)



OK

2.INSPECT NO. 1 INTEGRATION RELAY (EFI)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)

2.INSPECT NO. 1 INTEGRATION RELAY (EFI)
a.

Inspect the No. 1 integration relay (EFI) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, BODY GROUND)

NG

REPLACE NO. 1 INTEGRATION RELAY

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, BODY GROUND)
a.

Check the harness and connectors between the No. 1 integration relay and ECM.

i.

Remove the No. 1 integration relay from the engine room relay block.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
A52-34 (MREL) - 1B-2 Always Below 1 Ω
A52-3 (+B) - 1B-4 Always Below 1 Ω
A52-2 (+B2) - 1B-4 Always Below 1 Ω
A52-34 (MREL) or 1B-2 - Body ground Always 10 kΩ or higher
A52-3 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
A52-2 (+B2) or 1B-4 - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
A38-34 (MREL) - 1B-2 Always Below 1 Ω
A38-3 (+B) - 1B-4 Always Below 1 Ω
A38-2 (+B2) - 1B-4 Always Below 1 Ω
A38-34 (MREL) or 1B-2 - Body ground Always 10 kΩ or higher
A38-3 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
A38-2 (+B2) or 1B-4 - Body ground Always 10 kΩ or higher




b.

Check the harness and connectors between the No. 1 integration relay and body ground.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-3 - Body ground Always Below 1 Ω





OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C46-81 (E1) - Body ground Always Below 1 Ω

for LHD
Tester Connection Condition Specified Condition
C45-81 (E1) - Body ground Always Below 1 Ω




OK

5.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (IGSW VOLTAGE)
A385192E01
1.104,0.344 1.458,0.563 0.354,0.219 1.885,0.354 2.24,0.573 0.354,0.219 1.073,2.521 1.427,2.74 0.354,0.219 2.073,2.51 2.427,2.729 0.354,0.219 2.469,1.969 2.021,1.375 true 2.594,4.115 2.26,3.344 true 0.104,0.052 0.417,0.25 0.313,0.198 10 false *a 1.167,0.365 1.531,0.563 0.365,0.198 10 false C46 1.938,0.354 2.302,0.552 0.365,0.198 10 false C45 1.479,0.146 1.844,0.344 0.365,0.198 10 false *A 2.573,1.969 3.146,2.229 0.573,0.26 10 false 81 (E1) 2.25,2.979 2.615,3.177 0.365,0.198 10 false C45 1.135,2.542 1.5,2.74 0.365,0.198 10 false A52 1.333,2.333 1.698,2.531 0.365,0.198 10 false *A 2.115,2.521 2.479,2.719 0.365,0.198 10 false A38 2.281,0.125 2.646,0.323 0.365,0.198 10 false *B 2.344,2.313 2.708,2.51 0.365,0.198 10 false *B 2.646,4.167 3.365,4.396 0.719,0.229 10 false 28 (IGSW)

a.

Disconnect the ECM connectors.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RHD
Tester Connection Switch Condition Specified Condition
A52-28 (IGSW) - C46-81 (E1) Engine switch on (IG) 11 to 14 V

for LHD
Tester Connection Switch Condition Specified Condition
A38-28 (IGSW) - C45-81 (E1) Engine switch on (IG) 11 to 14 V


Text in Illustration
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to ECM)



OK

NG

6.INSPECT NO. 1 INTEGRATION RELAY (IG2)
6.INSPECT NO. 1 INTEGRATION RELAY (IG2)
a.

Inspect the No. 1 integration relay (IG2) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
1B-8 - A52-28 (IGSW) Always Below 1 Ω
1B-8 or A52-28 (IGSW) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
1B-8 - A38-28 (IGSW) Always Below 1 Ω
1B-8 or A38-28 (IGSW) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
Out of normal range A
Within normal range B




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - MAIN BODY ECU, BODY GROUND)
8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - MAIN BODY ECU, BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the Main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-6 - E2-11 (IG2D) Always Below 1 Ω
1B-7 - Body ground Always Below 1 Ω
1B-6 or E2-11 (IG2D) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR