Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM J

1UR-FE ENGINE CONTROL  SFI SYSTEM  ACIS Control Circuit  


DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

A233285E01
0.066,0.262 1.048,0.439 0.982,0.177 10 Intake Manifold 1.039,0.339 1.419,0.812 false 2.171,0.427 2.556,0.590 0.385,0.163 10 IACV 2.139,0.493 1.856,1.064 false 2.791,2.441 3.141,2.611 0.350,0.170 10 ECM 3.554,2.529 5.078,2.692 1.524,0.163 10 Throttle Position Sensor 2.153,3.107 3.885,3.270 1.732,0.163 10 Crankshaft Position Sensor 5.134,1.269 5.607,1.439 0.473,0.170 10 Closed 5.074,0.073 5.487,0.250 0.413,0.177 10 Open 2.868,0.164 4.676,0.355 1.809,0.191 10 Throttle Valve Position (deg.) 5.817,1.883 7.098,2.080 1.281,0.198 10 Engine Speed (rpm) 5.461,0.152 5.573,0.152 5.573,0.152 6.223,0.795 false 6.077,0.41 6.077,0.349 false 4.739,1.087 4.682,1.087 false 5.915,0.195 6.265,0.364 0.350,0.170 10 4350 4.5,1.015 4.680,1.167 0.180,0.152 10 50

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (OPERATE VACUUM SWITCHING VALVE FOR ACIS)
A233358E01
0.235,0.261 0.443,0.424 0.208,0.163 10 *a 0.297,2.646 0.482,2.793 0.185,0.147 10 *b 1.242,0.985 1.387,1.144 0.145,0.159 10 E 1.044,3.125 1.190,3.284 0.145,0.159 10 E 1.111,1.245 1.225,1.401 0.114,0.156 10 F 0.916,3.387 1.030,3.542 0.114,0.156 10 F 1.021,0.467 1.198,0.637 0.177,0.170 10 *c 0.54,1.597 0.716,1.767 0.177,0.170 10 *c 1.141,2.62 1.318,2.790 0.177,0.170 10 *c 2.585,2.972 2.762,3.142 0.177,0.170 10 *c

a.

Disconnect the vacuum hose from port F on the vacuum switching valve (for ACIS).


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.


e.

Operate the vacuum switching valve for ACIS.


f.

Check the vacuum switching valve air flow when switching the vacuum switching valve.

OK:
Test Condition Specified Condition
Vacuum switching valve is ON Air from port E flows out through port F
Vacuum switching valve is OFF Air from port E flows out through air filter


Text in Illustration
*a VSV is ON
*b VSV is OFF
*c Air



OK

2.CHECK VACUUM HOSES (VACUUM SWITCHING VALVE (FOR ACIS) - INTAKE AIR CONTROL VALVE, INTAKE MANIFOLD)

NG

4.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS)
2.CHECK VACUUM HOSES (VACUUM SWITCHING VALVE (FOR ACIS) - INTAKE AIR CONTROL VALVE, INTAKE MANIFOLD)

OK

3.INSPECT INTAKE MANIFOLD (INTAKE AIR CONTROL VALVE)

NG

REPAIR OR REPLACE VACUUM HOSES

3.INSPECT INTAKE MANIFOLD (INTAKE AIR CONTROL VALVE)

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS)
a.

Inspect the vacuum switching valve assembly (for ACIS) (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>VACUUM SWITCHING VALVE(for ACIS)>ON-VEHICLE INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACIS) - ECM AND NO. 2 INTEGRATION RELAY)

NG

REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR ACIS)

5.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACIS) - ECM AND NO. 2 INTEGRATION RELAY)
a.

Disconnect the vacuum switching valve (for ACIS) connector.


b.

Disconnect the ECM connector.


c.

Remove the No. 2 integration relay from the engine room relay block.


d.

Disconnect the No. 2 integration relay connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C129-2 - C46-62 (ACIS) Always Below 1 Ω
C129-1 - 1S-1 Always Below 1 Ω
C129-2 or C46-62 (ACIS) - Body ground Always 10 kΩ or higher
C129-1 or 1S-1 - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C129-2 - C45-62 (ACIS) Always Below 1 Ω
C129-1 - 1S-1 Always Below 1 Ω
C129-2 or C45-62 (ACIS) - Body ground Always 10 kΩ or higher
C129-1 or 1S-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR