Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  P0355  Ignition Coil "E" Primary / Secondary Circuit  P0356  Ignition Coil "F" Primary / Secondary Circuit  P0357  Ignition Coil "G" Primary / Secondary Circuit  P0358  Ignition Coil "H" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is stored, check the No. 1 ignition coil circuit.

·

If DTC P0352 is stored, check the No. 2 ignition coil circuit.

·

If DTC P0353 is stored, check the No. 3 ignition coil circuit.

·

If DTC P0354 is stored, check the No. 4 ignition coil circuit.

·

If DTC P0355 is stored, check the No. 5 ignition coil circuit.

·

If DTC P0356 is stored, check the No. 6 ignition coil circuit.

·

If DTC P0357 is stored, check the No. 7 ignition coil circuit.

·

If DTC P0358 is stored, check the No. 8 ignition coil circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A385075E01
3.938,1.26 3.938,0.479 3.938,0.479 4.083,0.479 true 5.073,0.719 5.406,0.24 true 0.073,0.104 2.198,0.406 2.125,0.302 10 false Reference (System Diagram): 0.385,2.344 1.688,2.854 1.302,0.51 10 false Crankshaft Position Sensor 0.406,3.469 1.323,3.917 0.917,0.448 10 false VVT Sensor 0.417,4.604 1.615,5.135 1.198,0.531 10 false Camshaft Position Sensor 0.156,5.813 1.958,6.823 1.802,1.01 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 0.823,7.552 1.792,7.948 0.969,0.396 10 false to Tachometer 1.813,7.698 2.229,7.948 0.417,0.25 10 false TACH 2.438,8.094 2.927,8.344 0.49,0.25 10 false ECM 2.531,7.552 2.927,7.792 0.396,0.24 10 false IGT8 2.552,6.677 2.948,6.917 0.396,0.24 10 false IGT7 2.563,5.802 2.958,6.042 0.396,0.24 10 false IGT6 2.542,4.927 2.958,5.167 0.417,0.24 10 false IGT5 2.552,4.073 2.958,4.313 0.406,0.24 10 false IGT4 2.573,3.188 2.979,3.427 0.406,0.24 10 false IGT3 2.542,2.729 2.948,2.969 0.406,0.24 10 false IGF2 2.563,2.333 2.969,2.573 0.406,0.24 10 false IGT2 2.552,1.344 2.958,1.583 0.406,0.24 10 false IGF1 2.573,0.948 2.979,1.188 0.406,0.24 10 false IGT1 4.365,0.042 5.635,0.313 1.271,0.271 10 false from Battery 4.156,0.365 4.677,0.646 0.521,0.281 10 false Igniter 5.49,0.146 6.635,0.583 1.146,0.438 10 false No. 1 Ignition Coil Assembly 5.375,1.01 6.313,1.25 0.938,0.24 10 false No. 1 Cylinder 4.323,1.792 5.333,2.021 1.01,0.229 10 false Ignition Coil 3.885,2.302 5.031,2.76 1.146,0.458 10 false No. 2 Ignition Coil Assembly 3.875,3.146 5.021,3.604 1.146,0.458 10 false No. 3 Ignition Coil Assembly 3.896,4.031 5.042,4.49 1.146,0.458 10 false No. 4 Ignition Coil Assembly 3.896,4.927 5.042,5.396 1.146,0.469 10 false No. 5 Ignition Coil Assembly 3.938,5.792 5.083,6.26 1.146,0.469 10 false No. 6 Ignition Coil Assembly 3.906,6.635 5.052,7.104 1.146,0.469 10 false No. 7 Ignition Coil Assembly 3.906,7.49 5.052,7.958 1.146,0.469 10 false No. 8 Ignition Coil Assembly 5.573,7.99 6.531,8.271 0.958,0.281 10 false No. 8 Cylinder 5.563,7.083 6.521,7.344 0.958,0.26 10 false No. 7 Cylinder 5.573,6.219 6.49,6.469 0.917,0.25 10 false No. 6 Cylinder 5.583,5.375 6.49,5.698 0.906,0.323 10 false No. 5 Cylinder 5.573,4.521 6.479,4.844 0.906,0.323 10 false No. 4 Cylinder 5.594,3.625 6.5,3.948 0.906,0.323 10 false No. 3 Cylinder 5.594,2.771 6.5,3.094 0.906,0.323 10 false No. 2 Cylinder 5.875,1.74 6.635,2.073 0.76,0.333 10 false Spark Plug

DTC No. DTC Detection Condition Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
P0357
P0358
No IGF signal is sent to the ECM while the engine is running (ECM does not receive any IGF signals despite the ECM sending an IGT signal to the igniter) (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1, IGT2 or IGT circuit (1 to 8) between ignition coil and ECM

·

No. 1 to No. 8 ignition coil assemblies

·

ECM



Reference: Inspection using an oscilloscope.

A385269E01
0.49,0.167 1.083,0.365 0.594,0.198 10 false 2 V/DIV. 0.833,0.708 1.135,0.885 0.302,0.177 10 false IGT 0.625,0.917 0.99,1.094 0.365,0.177 10 false GND 0.625,1.479 0.99,1.656 0.365,0.177 10 false GND 0.844,1.26 1.135,1.458 0.292,0.198 10 false IGF 1.656,1.844 2.688,2.042 1.031,0.198 10 false 20 msec./DIV.

Standard:
for RHD
Tester Connection Tool Setting Condition Specified Condition
C46-40 (IGT1) - C46-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C46-33 (IGT2) - C46-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C46-37 (IGT3) - C46-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C46-34 (IGT4) - C46-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C46-35 (IGT5) - C46-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C46-36 (IGT6) - C46-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C46-38 (IGT7) - C46-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C46-39 (IGT8) - C46-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C46-104 (IGF1) - C46-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C46-105 (IGF2) - C46-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown

for LHD
Tester Connection Tool Setting Condition Specified Condition
C45-40 (IGT1) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-33 (IGT2) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-37 (IGT3) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-34 (IGT4) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-35 (IGT5) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-36 (IGT6) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-38 (IGT7) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-39 (IGT8) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-104 (IGF1) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C45-105 (IGF2) - C45-81 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown


HINT:

While cranking or idling the engine, check the waveform between terminals IGT (1 to 8) and E1, and IGF1 or IGF2 and E1 of the ECM connector.



MONITOR DESCRIPTION

A115898E15
4.427,2.375 5.854,2.563 1.427,0.188 10 false Ignition Coil Assembly 4.135,1.542 4.615,1.729 0.479,0.188 10 false Igniter 5.396,1.365 6.198,1.604 0.802,0.24 10 false Ignition Coil 0.271,2.906 1.156,3.281 0.885,0.375 10 false Ignition Signal (IGT) 0.271,3.76 1.083,4.313 0.813,0.552 10 false Ignition Confirmation Signal (IGF) 1.604,3.552 2.167,3.729 0.563,0.177 10 false Normal 1.365,3.948 2.146,4.125 0.781,0.177 10 false Malfunction 3.479,4.521 4.427,4.708 0.948,0.188 10 false Circuit Open 5.802,4.99 6.323,5.156 0.521,0.167 10 false Time 1.781,1.667 2.177,1.844 0.396,0.177 10 false ECM 2.906,1.375 3.229,1.563 0.323,0.188 10 false IGT 2.906,1.802 3.229,1.99 0.323,0.188 10 false IGF

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Start the engine and run it at idle for 10 seconds or more.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
a.

Disconnect the ignition coil connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C4-4 (GND) - Body ground Always Below 1 Ω
C134-4 (GND) - Body ground Always Below 1 Ω
C130-4 (GND) - Body ground Always Below 1 Ω
C13-4 (GND) - Body ground Always Below 1 Ω
C8-4 (GND) - Body ground Always Below 1 Ω
C133-4 (GND) - Body ground Always Below 1 Ω
C131-4 (GND) - Body ground Always Below 1 Ω
C53-4 (GND) - Body ground Always Below 1 Ω



c.

Turn the engine switch on (IG).


U162854E01
0.11,0.103 0.310,0.291 0.200,0.188 10 *a 0.127,2.548 0.435,2.690 0.308,0.142 10 C13 0.586,2.188 0.945,2.330 0.360,0.142 10 C131 0.092,2.188 0.456,2.330 0.364,0.142 10 C130 0.637,2.548 0.914,2.690 0.276,0.142 10 C53 0.195,1.458 0.393,1.600 0.198,0.142 10 C4 0.66,1.458 0.900,1.600 0.239,0.142 10 C8 0.092,1.824 0.456,1.966 0.365,0.142 10 C134 0.586,1.824 0.945,1.966 0.360,0.142 10 C133 1.051,2.676 1.454,2.813 0.404,0.137 10 +B (+) 1.956,2.676 2.544,2.813 0.589,0.137 10 GND (-) 1.36,2.154 1.321,2.635 false 2.15,2.111 2.212,2.624 false

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C4-1 (+B) - C4-4 (GND) Engine switch on (IG) 11 to 14 V
C134-1 (+B) - C134-4 (GND) Engine switch on (IG) 11 to 14 V
C130-1 (+B) - C130-4 (GND) Engine switch on (IG) 11 to 14 V
C13-1 (+B) - C13-4 (GND) Engine switch on (IG) 11 to 14 V
C8-1 (+B) - C8-4 (GND) Engine switch on (IG) 11 to 14 V
C133-1 (+B) - C133-4 (GND) Engine switch on (IG) 11 to 14 V
C131-1 (+B) - C131-4 (GND) Engine switch on (IG) 11 to 14 V
C53-1 (+B) - C53-4 (GND) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Ignition Coil Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C4-2 (IGF1) - C46-104 (IGF1) Always Below 1 Ω
C134-2 (IGF2) - C46-105 (IGF2) Always Below 1 Ω
C130-2 (IGF2) - C46-105 (IGF2) Always Below 1 Ω
C13-2 (IGF1) - C46-104 (IGF1) Always Below 1 Ω
C8-2 (IGF2) - C46-105 (IGF2) Always Below 1 Ω
C133-2 (IGF1) - C46-104 (IGF1) Always Below 1 Ω
C131-2 (IGF1) - C46-104 (IGF1) Always Below 1 Ω
C53-2 (IGF2) - C46-105 (IGF2) Always Below 1 Ω
C4-3 (IGT1) - C46-40 (IGT1) Always Below 1 Ω
C134-3 (IGT2) - C46-33 (IGT2) Always Below 1 Ω
C130-3 (IGT3) - C46-37 (IGT3) Always Below 1 Ω
C13-3 (IGT4) - C46-34 (IGT4) Always Below 1 Ω
C8-3 (IGT5) - C46-35 (IGT5) Always Below 1 Ω
C133-3 (IGT6) - C46-36 (IGT6) Always Below 1 Ω
C131-3 (IGT7) - C46-38 (IGT7) Always Below 1 Ω
C53-3 (IGT8) - C46-39 (IGT8) Always Below 1 Ω
C4-2 (IGF1) or C46-104 (IGF1) - Body ground Always 10 kΩ or higher
C134-2 (IGF2) or C46-105 (IGF2) - Body ground Always 10 kΩ or higher
C130-2 (IGF2) or C46-105 (IGF2) - Body ground Always 10 kΩ or higher
C13-2 (IGF1) or C46-104 (IGF1) - Body ground Always 10 kΩ or higher
C8-2 (IGF2) or C46-105 (IGF2) - Body ground Always 10 kΩ or higher
C133-2 (IGF1) or C46-104 (IGF1) - Body ground Always 10 kΩ or higher
C131-2 (IGF1) or C46-104 (IGF1) - Body ground Always 10 kΩ or higher
C53-2 (IGF2) or C46-105 (IGF2) - Body ground Always 10 kΩ or higher
C4-3 (IGT1) or C46-40 (IGT1) - Body ground Always 10 kΩ or higher
C134-3 (IGT2) or C46-33 (IGT2) - Body ground Always 10 kΩ or higher
C130-3 (IGT3) or C46-37 (IGT3) - Body ground Always 10 kΩ or higher
C13-3 (IGT4) or C46-34 (IGT4) - Body ground Always 10 kΩ or higher
C8-3 (IGT5) or C46-35 (IGT5) - Body ground Always 10 kΩ or higher
C133-3 (IGT6) or C46-36 (IGT6) - Body ground Always 10 kΩ or higher
C131-3 (IGT7) or C46-38 (IGT7) - Body ground Always 10 kΩ or higher
C53-3 (IGT8) or C46-39 (IGT8) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C4-2 (IGF1) - C45-104 (IGF1) Always Below 1 Ω
C134-2 (IGF2) - C45-105 (IGF2) Always Below 1 Ω
C130-2 (IGF2) - C45-105 (IGF2) Always Below 1 Ω
C13-2 (IGF1) - C45-104 (IGF1) Always Below 1 Ω
C8-2 (IGF2) - C45-105 (IGF2) Always Below 1 Ω
C133-2 (IGF1) - C45-104 (IGF1) Always Below 1 Ω
C131-2 (IGF1) - C45-104 (IGF1) Always Below 1 Ω
C53-2 (IGF2) - C45-105 (IGF2) Always Below 1 Ω
C4-3 (IGT1) - C45-40 (IGT1) Always Below 1 Ω
C134-3 (IGT2) - C45-33 (IGT2) Always Below 1 Ω
C130-3 (IGT3) - C45-37 (IGT3) Always Below 1 Ω
C13-3 (IGT4) - C45-34 (IGT4) Always Below 1 Ω
C8-3 (IGT5) - C45-35 (IGT5) Always Below 1 Ω
C133-3 (IGT6) - C45-36 (IGT6) Always Below 1 Ω
C131-3 (IGT7) - C45-38 (IGT7) Always Below 1 Ω
C53-3 (IGT8) - C45-39 (IGT8) Always Below 1 Ω
C4-2 (IGF1) or C45-104 (IGF1) - Body ground Always 10 kΩ or higher
C134-2 (IGF2) or C45-105 (IGF2) - Body ground Always 10 kΩ or higher
C130-2 (IGF2) or C45-105 (IGF2) - Body ground Always 10 kΩ or higher
C13-2 (IGF1) or C45-104 (IGF1) - Body ground Always 10 kΩ or higher
C8-2 (IGF2) or C45-105 (IGF2) - Body ground Always 10 kΩ or higher
C133-2 (IGF1) or C45-104 (IGF1) - Body ground Always 10 kΩ or higher
C131-2 (IGF1) or C45-104 (IGF1) - Body ground Always 10 kΩ or higher
C53-2 (IGF2) or C45-105 (IGF2) - Body ground Always 10 kΩ or higher
C4-3 (IGT1) or C45-40 (IGT1) - Body ground Always 10 kΩ or higher
C134-3 (IGT2) or C45-33 (IGT2) - Body ground Always 10 kΩ or higher
C130-3 (IGT3) or C45-37 (IGT3) - Body ground Always 10 kΩ or higher
C13-3 (IGT4) or C45-34 (IGT4) - Body ground Always 10 kΩ or higher
C8-3 (IGT5) or C45-35 (IGT5) - Body ground Always 10 kΩ or higher
C133-3 (IGT6) or C45-36 (IGT6) - Body ground Always 10 kΩ or higher
C131-3 (IGT7) or C45-38 (IGT7) - Body ground Always 10 kΩ or higher
C53-3 (IGT8) or C45-39 (IGT8) - Body ground Always 10 kΩ or higher




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355, P0356, P0357 OR P0358)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355, P0356, P0357 OR P0358)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Shuffle the arrangement of the ignition coil assemblies (among the No. 1 to No. 8 cylinders).

NOTICE:

Do not shuffle the connectors.



f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Check the DTCs output on the GTS.

Result
Result Proceed to
Same DTC is output A
Different ignition coil DTC is output B



A

B