| *1 | Camshaft Position Sensor |
| *2 | Crankshaft Position Sensor |
| *3 | ECM |
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emissions levels. High concentrations of HC can also cause increases in the Three-way Catalytic Converter (TWC) temperature, which may cause damage to the Three-way Catalytic Converter (TWC). To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the Three-way Catalytic Converter (TWC) reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire rate exceeds the threshold level, the ECM illuminates the MIL and stores a DTC.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0300 | Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2 trip detection logic):
·
High temperature misfire occurs in the Three-way Catalytic Converter (MIL blinks when detect immediately). ·
Catalyst deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Air induction system ·
ECM |
| P0301
P0302 P0303 P0304 P0305 P0306 P0307 P0308 |
Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
·
High temperature misfire occurs in the Three-way Catalytic Converter (MIL blinks when detect immediately). ·
Catalyst deterioration misfire occurs (MIL illuminates). |
When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.
The ECM illuminates the MIL and stores a DTC when the following condition, which could cause catalyst deterioration, is detected (2 trip detection logic).
An excessive misfiring rate (approximately 130 to 160 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following condition, which could cause damage to the three-way catalytic converter , is detected.
A sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Record the DTC(s) and freeze frame data.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE).
Read the misfire counts of each cylinder (cylinder No. 1 to No. 8) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle several times with the conditions, such as engine speed and engine load, as shown in Misfire RPM and Misfire Load in the freeze frame data.
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below with the engine speed and engine load the same as Misfire RPM and Misfire Load in the freeze frame data.
| Engine Speed | Duration |
|---|---|
| Idling | 8.0 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
Check whether misfires have occurred by checking DTCs and freeze frame data.
Do not turn the engine switch off until the stored DTCs and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTCs, freeze frame data and other data will be cleared.
Record the DTCs, freeze frame data and misfire counts.
Turn the engine switch off and wait for at least 30 seconds.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors may be a cause of the problem:
The fuel level is low.
Improper fuel is being used.
The spark plugs are dirty.
After finishing repairs, check that no misfires occur in each cylinder (cylinder No. 1, No. 2, No. 3, No. 4, No. 5, No. 6, No. 7 and No. 8).
Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after the repairs.
For 6 and 8 cylinder engines, the ECM intentionally does not store the specific misfiring cylinder DTCs at high engine speed. If misfires only occur during high engine speed driving, only DTC P0300 is stored.
In the event of DTC P0300 being output, perform the following operations:
Clear the DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine and conduct the confirmation driving pattern.
Read the misfiring rates of each cylinder or the DTCs using the GTS.
Repair the cylinders that have a high misfiring rate or are indicated by the DTCs.
After finishing repairs, conduct the confirmation driving pattern again in order to verify that DTC P0300 is not stored.
When one of Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).
When Coolant Temp in the freeze frame data is below 75°C (167°F), the misfires may have occurred only while warming up the engine.
An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 is output | A |
| P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 and other DTCs are output | B |
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections (See page Engine / Hybrid System>1UR-FE (EMISSION CONTROL)>EMISSION CONTROL SYSTEM(w/ Secondary Air Injection System)>ON-VEHICLE INSPECTION).
PCV hose is connected correctly and is not damaged.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Rate, #2, #3, #4, #5, #6, #7 and #8.
Allow the engine to idle.
Read each value for CYL #1 to #8 (Cylinder #1 Misfire Rate to #8) displayed on the GTS. If no misfire counts occur in any cylinders, perform the following procedures:
Move the shift lever to D.
Check CYL #1 to #8 (Cylinder #1 Misfire Rate to #8).
If misfire counts are still not displayed, perform procedure "A" and "B", and then check the misfire counts again.
Procedure A: Drive the vehicle while satisfying the Misfire RPM and Misfire Load values noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedure above.
Procedure B: Read CYL #1 to #8 (Cylinder #1 Misfire Rate to #8) or the DTCs output on the GTS.
| Result | Proceed to |
|---|---|
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
If the freeze frame data's record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.
If the freeze frame data's record of the Engine Run Time is less than 120 seconds, the misfire may be detected immediately after the engine is started.
A
B
Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Perform a spark test (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
If the result of the spark test is normal, proceed to the next step.
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
OK
NG
OK
NG
OK
NG
Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL INJECTOR>INSPECTION).
OK
NG
Check the air induction system for vacuum leakage (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leakage in air induction system.
OK
NG
Check the fuel pressure (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
Between 18.3 gm/s. and 25.8 gm/s. (shift lever: N; A/C: Off).
OK
NG
OK
NG
Check the air induction system for vacuum leakage (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leakage in air induction system.
OK
NG
Check the fuel pressure (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: Off).
OK
NG
OK
NG
Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Perform a spark test (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
If the result of the spark test is normal, proceed to the next step.
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
OK
NG
OK
NG
OK
NG
Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL INJECTOR>INSPECTION).
OK
NG
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
Repair any problems.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.
Check the DTC judgment result.
| Display (DTC Output) | Proceed to |
|---|---|
| ABNORMAL
(P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 output) |
A |
| NORMAL
(No DTC output) |
B |
A
B
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-3 (VG) - C46-74 (VG) | Always | Below 1 Ω |
| C50-2 (E2G) - C46-75 (E2G) | Always | Below 1 Ω |
| C50-3 (VG) or C46-74 (VG) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-3 (VG) - C45-74 (VG) | Always | Below 1 Ω |
| C50-2 (E2G) - C45-75 (E2G) | Always | Below 1 Ω |
| C50-3 (VG) or C45-74 (VG) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the mass air flow meter assembly (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).
If the results of the inspections performed in steps 14 and 19 indicated no problem, proceed to the next step without replacing the mass air flow meter assembly.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.
Check the DTC judgment result.
| Display (DTC Output) | Proceed to |
|---|---|
| NORMAL
(No DTC output) |
A |
| ABNORMAL
(P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 output) |
B |
A
B
Check the fuel lines for leaks or blockage.
OK
NG