Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The stop light switch is part of a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0724 Stop light switch remains on even when the vehicle is driven in a GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM



MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be stored.

CONFIRMATION DRIVING PATTERN

A199312E31
1.414,2.021 1.792,2.191 0.378,0.170 10 Idling 0.879,2.35 1.792,2.659 0.913,0.309 10 Engine Switch on (IG) 2.509,2.467 2.707,2.665 0.198,0.198 10 [A] 2.583,3.079 3.295,3.221 0.711,0.142 10 5 seconds 3.27,3.494 3.474,3.674 0.205,0.180 10 [B] 3.409,1.912 3.619,2.090 0.210,0.178 10 [C] 6.755,3.475 6.953,3.672 0.198,0.198 10 [E] 4.043,1.495 4.253,1.673 0.210,0.178 10 [D] 0.479,1.201 1.827,1.385 1.348,0.184 10 30 km/h (18.63 mph) 0.631,1.726 1.867,1.903 1.237,0.177 10 3 km/h (1.86 mph)

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0724.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].



12.

Start the engine [C].

13.

Accelerate the vehicle to 30 km/h (18.63 mph) or more, and then depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less [D]. Repeat step [D] 5 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result [E].


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Using the GTS, the Data List item "Stop Light Switch" can be read.


Item Measurement Item/
Range (Display)
Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status/
ON or OFF
·

Brake pedal depressed: ON

·

Brake pedal released: OFF


-

PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the stop light switch assembly installation.

OK:

Stop light switch assembly is installed correctly.




OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RHD
Tester Connection Condition Specified Condition
A52-36 (STP) - Body ground Brake pedal is depressed 7.5 to 14 V
A52-36 (STP) - Body ground Brake pedal is released Below 1.5 V

for LHD
Tester Connection Condition Specified Condition
A38-36 (STP) - Body ground Brake pedal is depressed 7.5 to 14 V
A38-36 (STP) - Body ground Brake pedal is released Below 1.5 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR