Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0057  Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)  P0058  Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  P105D  O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON  


DESCRIPTION


HINT:
·

When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. The ECM continues operating in fail-safe mode until the engine switch is turned off.

·

The ECM provides a pulse-width modulated control circuit to adjust the current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.

A164717E29
0.042,0.01 2.667,0.375 2.625,0.365 10 false Reference (System Diagram): 2.813,1.188 3.521,1.365 0.708,0.177 10 false EFI NO. 2 2.104,2.656 2.74,3.156 0.635,0.5 10 false EFI MAIN NO. 1 1.073,1.219 1.76,1.563 0.688,0.344 10 false EFI MAIN NO. 1 1.021,3.333 1.573,3.531 0.552,0.198 10 false Ground 3.76,2.146 4.563,2.448 0.802,0.302 10 false HO2 Sensor 3.552,0.938 3.802,1.146 0.25,0.208 10 false +B 4.344,0.938 4.75,1.146 0.406,0.208 10 false HT1B 3.563,1.5 3.844,1.729 0.281,0.229 10 false E1 4.344,1.5 4.792,1.688 0.448,0.188 10 false OX1B 5.375,1.479 5.823,1.688 0.448,0.208 10 false OX1B 5.396,2.271 5.854,2.49 0.458,0.219 10 false EX1B 3.906,1.188 4.417,1.396 0.51,0.208 10 false Heater 3.917,1.813 4.458,2 0.542,0.188 10 false Sensor 6.083,3.438 6.51,3.677 0.427,0.24 10 false ECM 5.365,0.948 5.781,1.146 0.417,0.198 10 false HT1B 5.385,2.854 5.833,3.083 0.448,0.229 10 false MREL 0.458,1 0.927,1.406 0.469,0.406 10 false from Battery



DTC No. DTC Detection Condition Trouble Area
P0037
P0057
The heater current is below the specified value while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor heater circuit

·

Heated oxygen sensor heater (for Sensor 2)

·

No. 2 integration relay

·

ECM


P0038
P0058
The heater current is higher than the specified value while the heater is operating (1 trip detection logic).
·

Short in heated oxygen sensor heater circuit

·

Heated oxygen sensor heater (for Sensor 2)

·

No. 2 integration relay

·

ECM


P102D
P105D
The heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated oxygen sensor heater range check (P0037, P0038, P0057, P0058, P102D and P105D):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.


CONFIRMATION DRIVING PATTERN

A198819E02
0.749,0.969 1.396,1.162 0.647,0.193 10 3000 rpm 0.946,1.739 1.352,1.900 0.406,0.161 10 Idling 0.416,2.006 1.379,2.344 0.964,0.338 10 Engine Switch on (IG) 1.926,2.132 2.161,2.297 0.235,0.165 10 [A] 2.762,1.622 2.955,1.815 0.193,0.193 10 [B] 4.026,0.868 4.283,1.006 0.258,0.137 10 [C] 5.39,1.6 5.613,1.782 0.223,0.181 10 [D] 2.272,2.589 3.465,2.745 1.193,0.156 10 5 minutes or more 4.873,2.608 6.066,2.764 1.193,0.156 10 5 minutes or more 3.85,2.617 4.423,2.782 0.573,0.165 10 1 minute 5.98,3.028 6.182,3.230 0.202,0.202 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0037, P0038, P0057, P0058, P102D or P105D.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 2 refers to the sensor mounted behind the Three-way Catalytic Converter (TWC) and located far from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [O2 Heater B1S2, O2 Heater B2S2, O2 Heater Curr Val B1S2 and O2 Heater Curr Val B2S2] (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF HEATED OXYGEN SENSOR)
U163331E02
1.979,1.083 2.438,0.792 false 1.927,3.469 2.375,3.177 false 0.271,0.094 0.438,0.292 0.167,0.198 10 false *a 2.51,0.625 2.74,0.844 0.229,0.219 10 false +B 0.49,3.604 0.854,3.802 0.365,0.198 10 false C56 0.438,1.25 0.813,1.448 0.375,0.198 10 false C20 2.427,3.021 2.656,3.24 0.229,0.219 10 false +B 0.885,1.177 1.083,1.333 0.198,0.156 10 false *b 0.927,3.552 1.125,3.708 0.198,0.156 10 false *c

a.

Disconnect the heated oxygen sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C20-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
C56-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Heated Oxygen Sensor)
*b Bank 1 sensor 2
*c Bank 2 sensor 2



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.INSPECT NO. 2 INTEGRATION RELAY (EFI MAIN NO. 1)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C20-1 (HT1B) - C46-45 (HT1B) Always Below 1 Ω
C56-1 (HT2B) - C46-44 (HT2B) Always Below 1 Ω
C20-1 (HT1B) or C46-45 (HT1B) - Body ground Always 10 kΩ or higher
C56-1 (HT2B) or C46-44 (HT2B) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C20-1 (HT1B) - C45-45 (HT1B) Always Below 1 Ω
C56-1 (HT2B) - C45-44 (HT2B) Always Below 1 Ω
C20-1 (HT1B) or C45-45 (HT1B) - Body ground Always 10 kΩ or higher
C56-1 (HT2B) or C45-44 (HT2B) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Read the output pending DTCs using the GTS.

Result
Result Proceed to
No pending DTC is output A
Pending DTC P0037, P0038, P0057, P0058, P102D and/or P105D is output B



A

B

5.INSPECT NO. 2 INTEGRATION RELAY (EFI MAIN NO. 1)
a.

Inspect the No. 2 integration relay (EFI MAIN NO. 1) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 2 INTEGRATION RELAY)

NG

REPLACE NO. 2 INTEGRATION RELAY (EFI MAIN NO. 1)

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 2 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor connector.


b.

Remove the No. 2 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C20-2 (+B) - 1S-1 Always Below 1 Ω
C56-2 (+B) - 1S-1 Always Below 1 Ω
C20-2 (+B) or 1S-1 - Body ground Always 10 kΩ or higher
C56-2 (+B) or 1S-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR