Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil, closing the contacts of the integration relay (EFI relay) and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

U163836E02
1.448,4.51 2.344,4.677 0.896,0.167 10 false *1: for LHD 1.448,4.823 2.344,4.99 0.896,0.167 10 false *2: for RHD 1.448,5.135 3.344,5.302 1.896,0.167 10 false *3: w/ Entry and Start System 1.448,5.448 3.458,5.615 2.01,0.167 10 false *4: w/o Entry and Start System 6.427,5.5 6.833,5.698 0.406,0.198 10 false ECM 6.146,1.625 6.563,1.802 0.417,0.177 10 false IGSW 5.396,1.729 5.75,1.948 0.354,0.219 10 false A38 5.385,2.406 5.698,2.594 0.313,0.188 10 false A38 5.396,2.979 5.708,3.146 0.313,0.167 10 false A38 5.385,3.969 5.74,4.208 0.354,0.24 10 false A38 5.385,4.979 5.708,5.146 0.323,0.167 10 false C45 5.76,1.51 6.104,1.667 0.344,0.156 10 false 28*2 5.813,2.177 6.104,2.333 0.292,0.156 10 false 2*2 5.802,2.771 6.094,2.927 0.292,0.156 10 false 1*2 4.635,3.771 4.792,3.938 0.156,0.167 10 false 8 4.635,3.219 4.781,3.385 0.146,0.167 10 false 4 4.604,2.771 4.823,2.958 0.219,0.188 10 false 11 4.656,1.573 4.76,1.729 0.104,0.156 10 false 7 5.771,4.74 6.177,4.938 0.406,0.198 10 false 81*2 5.76,3.76 6.125,3.958 0.365,0.198 10 false 44*2 2.802,3.646 3.927,3.813 1.125,0.167 10 false EFI MAIN NO. 1 2.281,1.896 2.927,2.063 0.646,0.167 10 false IG2 MAIN 0.396,1.063 1.042,1.229 0.646,0.167 10 false J/B LH-B 3.677,1.927 4.802,2.125 1.125,0.198 10 false ENG-IG2 NO. 1 5.479,0.313 5.854,0.469 0.375,0.156 10 false IG1D 5.281,0.229 5.458,0.385 0.177,0.156 10 false 3 3.25,0.24 3.427,0.396 0.177,0.156 10 false 6 2.542,0.229 2.719,0.385 0.177,0.156 10 false 5 5.292,0.792 5.719,0.979 0.427,0.188 10 false E128 5.292,0.958 7.115,1.188 1.823,0.229 10 false Smart Key ECU Assembly*3 1.875,0.771 4.24,1 2.365,0.229 10 false Ignition or Starter Switch Assembly*4 0.542,4.698 1.031,4.885 0.49,0.188 10 false Battery 6.156,2.375 6.365,2.542 0.208,0.167 10 false +B 6.156,2.948 6.448,3.115 0.292,0.167 10 false +B2 6.156,3.854 6.594,4.042 0.438,0.188 10 false MREL 6.156,4.958 6.354,5.115 0.198,0.156 10 false E1 1.583,1.74 1.854,1.906 0.271,0.167 10 false 1Y 1.573,1.531 1.802,1.688 0.229,0.156 10 false 1*1 1.885,1.531 2.188,1.688 0.302,0.156 10 false 1*2 4.583,3.979 4.854,4.188 0.271,0.208 10 false 1S 4.583,2.99 4.844,3.219 0.26,0.229 10 false 1S 4.635,1.177 4.792,1.333 0.156,0.156 10 false 2 4.594,1.365 4.823,1.531 0.229,0.167 10 false 1R 4.583,1.74 4.844,1.938 0.26,0.198 10 false 1P 4.583,3.427 4.823,3.604 0.24,0.177 10 false 1S 3.292,4.365 4.917,4.604 1.625,0.24 10 false Integration Relay 0.719,1.896 1.167,2.094 0.448,0.198 10 false P/I-B 3.052,2.344 3.698,2.51 0.646,0.167 10 false IG2 MAIN 2.396,3.094 3.104,3.448 0.708,0.354 10 false EFI MAIN NO. 1 5.771,1.75 6.104,1.927 0.333,0.177 10 false A52 5.771,2.406 6.094,2.615 0.323,0.208 10 false A52 5.771,2.979 6.104,3.177 0.333,0.198 10 false A52 5.781,3.969 6.104,4.177 0.323,0.208 10 false A52 5.781,4.979 6.104,5.167 0.323,0.188 10 false C46 5.365,1.51 5.74,1.667 0.375,0.156 10 false 28*1 5.375,4.74 5.781,4.938 0.406,0.198 10 false 81*1 5.365,3.76 5.729,3.948 0.365,0.188 10 false 44*1 5.427,2.177 5.719,2.333 0.292,0.156 10 false 2*1 5.438,2.771 5.729,2.927 0.292,0.156 10 false 1*1 1.917,1.74 2.188,1.906 0.271,0.167 10 false 1X 0.708,0.5 1.094,0.698 0.385,0.198 10 false AM2 1.865,0.594 2.292,0.781 0.427,0.188 10 false E93 3.094,0.458 3.427,0.625 0.333,0.167 10 false IG2 2.542,0.458 2.927,0.646 0.385,0.188 10 false AM2

CAUTION / NOTICE / HINT

PROCEDURE

1.INSPECT INTEGRATION RELAY (POWER SOURCE)
U163774E03
0.75,1.917 1.031,2.115 0.281,0.198 10 false 1X 0.208,0.25 0.438,0.448 0.229,0.198 10 false *a 0.76,1.563 1.042,1.76 0.281,0.198 10 false 1Y 1.073,1.802 1.302,2 0.229,0.198 10 false *c 1.063,1.438 1.292,1.635 0.229,0.198 10 false *b

a.

Remove the integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V



*a Front view of wire harness connector
(Integration relay)
*b for LHD
*c for RHD


OK

2.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BODY GROUND)
a.

Remove the integration relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1S-4 - Body ground Always Below 1 Ω




OK

3.INSPECT INTEGRATION RELAY (EFI MAIN NO. 1 AND IG2 MAIN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INTEGRATION RELAY (EFI MAIN NO. 1 AND IG2 MAIN)

OK

4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)

NG

REPLACE INTEGRATION RELAY

4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A38-44 (MREL) - 1S-8 Always Below 1 Ω
A38-2 (+B) - 1S-11 Always Below 1 Ω
A38-1 (+B2) - 1S-11 Always Below 1 Ω
A38-44 (MREL) or 1S-8 - Body ground Always 10 kΩ or higher
A38-2 (+B) or 1S-11 - Body ground Always 10 kΩ or higher
A38-1 (+B2) or 1S-11 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-44 (MREL) - 1S-8 Always Below 1 Ω
A52-2 (+B) - 1S-11 Always Below 1 Ω
A52-1 (+B2) - 1S-11 Always Below 1 Ω
A52-44 (MREL) or 1S-8 - Body ground Always 10 kΩ or higher
A52-2 (+B) or 1S-11 - Body ground Always 10 kΩ or higher
A52-1 (+B2) or 1S-11 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C45-81 (E1) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C46-81 (E1) - Body ground Always Below 1 Ω




OK

6.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ECM (IGSW VOLTAGE)
A384779E01
1.438,0.76 1.854,1.01 0.417,0.25 2.24,0.76 2.656,1.01 0.417,0.25 4.74,0.708 5.156,0.958 0.417,0.25 5.552,0.708 5.969,0.958 0.417,0.25 2.49,1.729 2.865,2.198 true 5.74,1.5 6.26,2.083 true 0.313,0.104 2.615,0.458 2.302,0.354 10 false Front view of wire harness connector: (to ECM) 1.51,0.802 1.833,0.99 0.323,0.188 10 false C45 2.323,0.813 2.646,1 0.323,0.188 10 false C46 1.896,0.698 2.125,0.896 0.229,0.198 10 false *1 2.719,0.698 2.948,0.896 0.229,0.198 10 false *2 2.781,2.229 3.354,2.438 0.573,0.208 10 false 81 (E1) 5.938,2.146 6.74,2.385 0.802,0.24 10 false 28 (IGSW) 4.823,0.75 5.146,0.938 0.323,0.188 10 false A38 5.198,0.625 5.427,0.823 0.229,0.198 10 false *1 5.635,0.75 5.958,0.938 0.323,0.188 10 false A52 6.021,0.646 6.25,0.844 0.229,0.198 10 false *2 0.115,2.063 0.958,2.271 0.844,0.208 10 false *1: for LHD 0.115,2.396 0.958,2.604 0.844,0.208 10 false *2: for RHD

a.

Disconnect the ECM connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A38-28 (IGSW) - C45-81 (E1) Ignition switch ON 11 to 14 V

for RHD
Tester Connection Switch Condition Specified Condition
A52-28 (IGSW) - C46-81 (E1) Ignition switch ON 11 to 14 V




OK

NG

7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A38-28 (IGSW) - 1P-7 Always Below 1 Ω
A38-28 (IGSW) or 1P-7 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-28 (IGSW) - 1P-7 Always Below 1 Ω
A52-28 (IGSW) or 1P-7 - Body ground Always 10 kΩ or higher



Result
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C


A

8.CHECK HARNESS AND CONNECTOR (SMART KEY ECU ASSEMBLY - INTEGRATION RELAY)

B

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - INTEGRATION RELAY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SMART KEY ECU ASSEMBLY - INTEGRATION RELAY)
a.

Disconnect the smart key ECU assembly connector.


b.

Disconnect the integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E128-3 (IG1D) - 1R-2 Always Below 1 Ω
E128-3 (IG1D) or 1R-2 - Body ground Always 10 kΩ or higher




OK

CHECK SMART KEY SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - INTEGRATION RELAY)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E93-6 (IG2) - 1R-2 Always Below 1 Ω
E93-6 (IG2) or 1R-2 - Body ground Always 10 kΩ or higher




OK

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>INSPECTION).



OK

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY