Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.

When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.

The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the inputs used for EGR control, etc.

A128639E01
1.699,0.22 3.248,0.428 1.549,0.208 10 Throttle Position Sensor 2.898,2.955 3.438,3.156 0.540,0.201 10 Hall IC 4.372,0.59 4.778,0.798 0.407,0.208 10 ECM 4.386,1.016 4.676,1.217 0.290,0.201 10 5 V 3.499,1.116 3.938,1.317 0.439,0.201 10 VCVL 3.574,1.739 4.037,1.940 0.463,0.201 10 VLU 3.499,2.347 3.899,2.548 0.401,0.201 10 EVLU 3.145,1.116 3.407,1.317 0.262,0.201 10 VC 3.145,2.347 3.379,2.548 0.234,0.201 10 E2 3.145,1.739 3.513,1.940 0.368,0.201 10 VTA 1.687,2.975 2.278,3.182 0.591,0.207 10 Magnet 2.521,2.036 2.858,3.036 false 2.415,2.572 2.217,3.063 false 1.687,0.625 2.278,0.833 0.591,0.207 10 Magnet 2.217,0.743 2.415,1.234 false

P0122
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Throttle position sensor (for Bank 1) output (VLU) is less than 0.2 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor (for Bank 1)

·

Open or short in VLU circuit

·

Open in VC circuit

·

ECM



P0123
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Throttle position sensor (for Bank 1) output (VLU) is more than 4.8 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor (for Bank 1)

·

Open in E2 circuit

·

VC and VLU circuits are short-circuited

·

ECM



P0222
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Throttle position sensor (for Bank 2) output (VLU2) is less than 0.2 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor (for Bank 2)

·

Open or short in VLU2 circuit

·

Open in VC circuit

·

ECM



P0223
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Throttle position sensor (for Bank 2) output (VLU2) is more than 4.8 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor (for Bank 2)

·

Open in E2 circuit

·

VC and VLU2 circuits are short-circuited

·

ECM



HINT:

If DTC P0122, P0123, P0222 and/or P0223 is stored, the following symptoms may appear:


- Intake booming noise

- Black smoke

- Lack of power

- Vibration at engine stop

- Turbo overspeed, turbo damage


MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

C129051E10
2.302,1.063 1.99,1.229 false 2.302,2.656 1.99,2.823 false 4.917,0.5 4.615,1.031 false 4.615,2.688 4.917,3.219 false 0.094,0.073 2.896,0.271 2.802,0.198 10 false Throttle Position Sensor Output Voltage (V) 2.063,0.552 2.635,0.75 0.573,0.198 10 false Closed 4.979,0.406 6.469,0.604 1.49,0.198 10 false Store P0123 or P0223 4.01,0.552 4.469,0.75 0.458,0.198 10 false Open 2.646,2.729 4.125,2.927 1.479,0.198 10 false Range of Operation 4.979,3.125 6.458,3.323 1.479,0.198 10 false Store P0122 or P0222 2.323,3.406 4.229,3.635 1.906,0.229 10 false Throttle Valve Opening Angle 4.083,3.198 4.313,3.396 0.229,0.198 10 false 70 2.26,3.198 2.396,3.396 0.135,0.198 10 false 0 1.677,2.771 2.031,2.969 0.354,0.198 10 false 0.20 1.969,2.406 2.354,2.604 0.385,0.198 10 false 0.69 1.969,1.375 2.323,1.573 0.354,0.198 10 false 3.49 1.677,1.115 2.042,1.313 0.365,0.198 10 false 4.80 1.969,0.927 2.323,1.125 0.354,0.198 10 false 5.00

WIRING DIAGRAM

A165736E03
2.035,1.119 2.274,1.313 0.239,0.194 10 VC 1.972,1.434 2.274,1.628 0.302,0.194 10 VTA 2.049,1.798 2.275,1.992 0.225,0.194 10 E2 5.265,1.119 5.691,1.313 0.427,0.194 10 VCVL 5.265,1.434 5.566,1.628 0.302,0.194 10 VLU 5.265,1.798 5.740,1.992 0.475,0.194 10 EVLU 2.381,1.205 2.565,1.388 0.184,0.184 10 1 2.381,1.534 2.565,1.718 0.184,0.184 10 3 2.381,1.884 2.565,2.068 0.184,0.184 10 2 4.982,1.205 5.165,1.388 0.184,0.184 10 91 4.982,1.534 5.165,1.718 0.184,0.184 10 93 5.265,3.605 5.719,3.799 0.455,0.194 10 VLU2 4.898,3.706 5.184,3.889 0.286,0.184 10 103 4.982,1.884 5.165,2.068 0.184,0.184 10 92 1.068,2.141 1.384,2.318 0.316,0.177 10 C83 1.068,2.323 3.454,2.500 2.385,0.177 10 Throttle Position Sensor (for Bank 1) 2.035,3.267 2.274,3.461 0.239,0.194 10 VC 1.897,3.598 2.273,3.792 0.376,0.194 10 VTA2 2.049,3.963 2.275,4.157 0.225,0.194 10 E2 2.381,3.353 2.565,3.537 0.184,0.184 10 1 2.381,3.699 2.565,3.882 0.184,0.184 10 3 2.381,4.049 2.565,4.232 0.184,0.184 10 2 1.068,4.306 1.361,4.483 0.292,0.177 10 C84 0.697,5.054 1.436,5.231 0.739,0.177 10 *1: for LHD 0.697,5.371 1.436,5.547 0.739,0.177 10 *2: for RHD 1.068,4.488 3.447,4.665 2.378,0.177 10 Throttle Position Sensor (for Bank 2) 5.422,4.632 6.311,4.812 0.889,0.180 10 C45*1, C46*2 5.422,4.793 5.786,4.973 0.364,0.180 10 ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
A385119E01
1.125,0.833 1.542,1.104 0.417,0.271 1.917,0.844 2.333,1.115 0.417,0.271 4.323,0.802 4.74,1.073 0.417,0.271 5.042,0.802 5.458,1.073 0.417,0.271 1.313,2.146 1.563,1.781 true 1.813,2.156 1.75,1.792 true 2.24,2.125 1.958,1.792 true 4.073,2.188 4.323,1.823 true 5.188,2.229 4.458,1.833 true 4.604,2.427 4.385,1.823 true 6,2.438 5.188,1.833 true 0.688,0.115 2.99,0.49 2.302,0.375 10 false Front view of wire harness connector: (to Throttle Position Sensor) 1.208,0.896 1.667,1.094 0.458,0.198 10 false C83 2,0.896 2.458,1.094 0.458,0.198 10 false C84 1.563,0.76 1.802,0.969 0.24,0.208 10 false *1 2.354,0.76 2.594,0.969 0.24,0.208 10 false *2 4.406,0.854 4.865,1.052 0.458,0.198 10 false C45 3.958,0.094 6.26,0.469 2.302,0.375 10 false Front view of wire harness connector: (to ECM) 4.76,0.708 5,0.917 0.24,0.208 10 false *1 5.125,0.844 5.583,1.042 0.458,0.198 10 false C46 5.479,0.708 5.719,0.917 0.24,0.208 10 false *4 1.188,2.167 1.49,2.365 0.302,0.198 10 false VC 4.229,2.469 5.031,2.667 0.802,0.198 10 false 92 (EVLU) 2.219,2.146 2.74,2.344 0.521,0.198 10 false VTA*1 3.563,2.219 4.333,2.417 0.771,0.198 10 false 91 (VCVL) 1.74,2.177 2.042,2.375 0.302,0.198 10 false E2 2.229,2.323 2.854,2.51 0.625,0.188 10 false VTA2*2 4.927,2.271 5.729,2.469 0.802,0.198 10 false 93 (VLU*1) 5.781,2.448 6.823,2.646 1.042,0.198 10 false 103 (VLU2*2) 0.125,1.479 1.104,1.677 0.979,0.198 10 false *1: for Bank 1 0.125,1.76 1.104,1.958 0.979,0.198 10 false *2: for Bank 2 0.125,2.052 1.104,2.25 0.979,0.198 10 false *3: for LHD 0.135,2.375 1.115,2.573 0.979,0.198 10 false *4: for RHD

a.

Disconnect the throttle position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Bank 1 (LHD)
Tester Connection Condition Specified Condition
C83-1 (VC) - C45-91 (VCVL) Always Below 1 Ω
C83-3 (VTA) - C45-93 (VLU) Always Below 1 Ω
C83-2 (E2) - C45-92 (EVLU) Always Below 1 Ω

for Bank 2 (LHD)
Tester Connection Condition Specified Condition
C84-1 (VC) - C45-91 (VCVL) Always Below 1 Ω
C84-3 (VTA2) - C45-103 (VLU2) Always Below 1 Ω
C84-2 (E2) - C45-92 (EVLU) Always Below 1 Ω

for Bank 1 (RHD)
Tester Connection Condition Specified Condition
C83-1 (VC) - C46-91 (VCVL) Always Below 1 Ω
C83-3 (VTA) - C46-93 (VLU) Always Below 1 Ω
C83-2 (E2) - C46-92 (EVLU) Always Below 1 Ω

for Bank 2 (RHD)
Tester Connection Condition Specified Condition
C84-1 (VC) - C46-91 (VCVL) Always Below 1 Ω
C84-3 (VTA2) - C46-103 (VLU2) Always Below 1 Ω
C84-2 (E2) - C46-92 (EVLU) Always Below 1 Ω


Standard Resistance (Check for Short):
for Bank 1 (LHD)
Tester Connection Condition Specified Condition
C83-1 (VC) or C45-91 (VCVL) - Body ground Always 10 kΩ or higher
C83-3 (VTA) or C45-93 (VLU) - Body ground Always 10 kΩ or higher
C83-2 (E2) or C45-92 (EVLU) - Body ground Always 10 kΩ or higher

for Bank 2 (LHD)
Tester Connection Condition Specified Condition
C84-1 (VC) or C45-91 (VCVL) - Body ground Always 10 kΩ or higher
C84-3 (VTA2) or C45-103 (VLU2) - Body ground Always 10 kΩ or higher
C84-2 (E2) or C45-92 (EVLU) - Body ground Always 10 kΩ or higher

for Bank 1 (RHD)
Tester Connection Condition Specified Condition
C83-1 (VC) or C46-91 (VCVL) - Body ground Always 10 kΩ or higher
C83-3 (VTA) or C46-93 (VLU) - Body ground Always 10 kΩ or higher
C83-2 (E2) or C46-92 (EVLU) - Body ground Always 10 kΩ or higher

for Bank 2 (RHD)
Tester Connection Condition Specified Condition
C84-1 (VC) or C46-91 (VCVL) - Body ground Always 10 kΩ or higher
C84-3 (VTA2) or C46-103 (VLU2) - Body ground Always 10 kΩ or higher
C84-2 (E2) or C46-92 (EVLU) - Body ground Always 10 kΩ or higher




OK

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
U162934E01
0.096,0.121 2.465,0.499 2.369,0.378 10 Front view of wire harness connector: (to Throttle Position Sensor) 1.16,1.121 1.473,1.287 0.313,0.165 10 C83 1.589,0.997 1.760,1.144 0.171,0.147 10 *1 0.119,2.785 1.074,2.931 0.956,0.147 10 *1: for Bank 1 0.119,3.091 0.994,3.238 0.876,0.147 10 *2: for Bank 2 2.001,1.121 2.314,1.287 0.313,0.165 10 C84 1.117,2.564 1.357,2.729 0.240,0.165 10 VC 1.933,2.564 2.173,2.729 0.240,0.165 10 E2 2.439,0.999 2.610,1.145 0.171,0.147 10 *2 1.474,2.081 1.273,2.53 false 1.754,2.077 2.009,2.544 false

Disconnect the throttle position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Bank 1
Tester Connection Switch Condition Specified Condition
C83-1 (VC) - C83-2 (E2) Ignition switch ON 4.5 to 5.5 V

for Bank 2
Tester Connection Switch Condition Specified Condition
C84-1 (VC) - C84-2 (E2) Ignition switch ON 4.5 to 5.5 V




OK

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1 or Bank 2)

NG

5.REPLACE ECM
3.REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1 or Bank 2)
a.

Replace the diesel throttle body assembly (for Bank 1 or Bank 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).



NEXT

4.READ VALUE USING INTELLIGENT TESTER
4.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.



d.

Enter the following menus: Powertrain / Engine / Data List / Actual Throttle position or Actual Throttle position #2.


e.

Check the movement of the throttle valve when idling the engine after starting it from ignition switch ON.

OK
Condition Tester Display
Ignition switch ON -5 to 5%
Idling 0 to 90%



OK

END

NG

5.REPLACE ECM
5.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 3 seconds.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END