Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0110  Intake Air Temperature Circuit  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

The intake air temperature sensor is built into the Mass Air Flow (MAF) meter and senses the intake air temperature.

A thermistor built into the sensor changes its resistance value according to the intake air temperature.

The lower the intake air temperature, the greater the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The intake air temperature sensor is connected to the ECM.

The 5 V power source voltage in the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with changes in the intake air temperature, the potential at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.

A385085E01
1.417,2.042 1.688,1.625 1.688,1.625 1.823,1.625 false 0.198,0.094 1.427,0.292 1.229,0.198 10 false (Fig. 1) 0.177,0.469 1.406,0.667 1.229,0.198 10 false Resistance kΩ 1.26,4.115 2.698,4.323 1.438,0.208 10 false Temperature °C (°F) 1.875,1.521 2.719,1.719 0.844,0.198 10 false Acceptable

P0110
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open or short in the intake air temperature (IAT) sensor for 0.5 seconds (1 trip detection logic).
·

Open or short in intake air temperature (IAT) sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM



P0112
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Short in the IAT sensor for 0.5 seconds (1 trip detection logic).
·

Short in IAT sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM



P0113
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open in the IAT sensor for 0.5 seconds (1 trip detection logic).
·

Open in IAT sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM



Related Data List
DTC No. Data List
P0110 Intake Air
P0112
P0113

HINT:
·

If DTC P0110, P0112 and/or P0113 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P0110, P0112 or P0113 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine / Data List / Intake Air.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



WIRING DIAGRAM

A165735E16
0.58,2.469 0.875,2.625 0.295,0.156 10 C50 0.58,2.628 2.592,2.983 2.012,0.355 10 Intake Air Temperature Sensor (Built into Mass Air Flow Meter) 5.684,2.693 6.581,2.849 0.897,0.156 10 C45*1, C46*2 5.684,2.852 6.039,3.026 0.355,0.174 10 ECM 2.182,1.666 2.415,1.840 0.233,0.174 10 E2 2.457,1.857 2.581,2.032 0.123,0.174 10 5 2.074,1.054 2.414,1.228 0.339,0.174 10 THA 5.54,1.666 5.772,1.840 0.233,0.174 10 E2 5.54,1.054 5.879,1.228 0.339,0.174 10 THA 2.457,1.245 2.581,1.420 0.123,0.174 10 4 5.292,1.857 5.486,2.032 0.194,0.174 10 75 5.301,1.245 5.486,1.420 0.185,0.174 10 71 6.161,0.937 6.287,1.091 0.126,0.154 10 R 6.254,0.652 6.517,0.817 0.262,0.165 10 5V 3.884,2.742 4.781,2.898 0.897,0.156 10 *1: for LHD 3.884,3.036 4.781,3.192 0.897,0.156 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are stored, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.


d.

Read the value.

OK:

Same as actual intake air temperature.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as actual intake air temperature) C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F) or more.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the mass air flow meter connector.

A385087E01
4.938,0.833 5.354,1.073 0.417,0.24 4.99,2.198 5.271,1.708 true 5.813,2.198 5.448,1.708 true 0.823,1.844 2.25,2.031 1.427,0.188 10 false Mass Air Flow Meter 4.823,2.208 5.24,2.396 0.417,0.188 10 false THA 2.865,1.656 3.188,1.844 0.323,0.188 10 false E2 2.781,1.25 3.104,1.438 0.323,0.188 10 false THA 4.073,0.063 6.385,0.438 2.313,0.375 10 false Front view of wire harness connector: (to Mass Air Flow Meter) 5.01,0.875 5.427,1.063 0.417,0.188 10 false C50 5.688,2.229 6.104,2.417 0.417,0.188 10 false E2 2.813,1.875 3.25,2.073 0.438,0.198 10 false ECM


b.

Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.


f.

Read the value.

OK:

140°C (284°F) or higher




OK

7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.

A385076E02
1.688,0.854 2.135,1.104 0.448,0.25 4.208,0.833 4.656,1.083 0.448,0.25 5.083,0.823 5.531,1.073 0.448,0.25 2.406,2.177 2.208,1.688 true 1.74,2.156 2.073,1.688 true 4.177,2.25 4.438,1.75 true 5.021,2.219 4.729,1.75 true 0.823,0.094 3.125,0.479 2.302,0.385 10 false Front view of wire harness connector: (to Mass Air Flow Meter) 1.771,0.906 2.156,1.104 0.385,0.198 10 false C50 1.615,2.219 2,2.417 0.385,0.198 10 false THA 2.333,2.208 2.719,2.406 0.385,0.198 10 false E2 3.802,0.083 6.104,0.469 2.302,0.385 10 false Front view of wire harness connector: (to ECM) 4.302,0.875 4.688,1.073 0.385,0.198 10 false C45 5.188,0.865 5.573,1.063 0.385,0.198 10 false C46 4.688,0.76 4.938,0.958 0.25,0.198 10 false *1 5.563,0.75 5.813,0.948 0.25,0.198 10 false *2 3.844,2.271 4.594,2.458 0.75,0.188 10 false 71 (THA) 4.802,2.25 5.552,2.438 0.75,0.188 10 false 75 (E2) 0.135,2.052 0.938,2.26 0.802,0.208 10 false *1: for LHD 0.135,2.385 0.938,2.594 0.802,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
C50-4 (THA) - C45-71 (THA) Always Below 1 Ω
C50-5 (E2) - C45-75 (E2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C50-4 (THA) - C46-71 (THA) Always Below 1 Ω
C50-5 (E2) - C46-75 (E2) Always Below 1 Ω




OK

9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A166688E01
0.111,2.319 1.446,2.487 1.335,0.168 10 Mass Air Flow Meter 2.629,2.319 3.000,2.482 0.371,0.163 10 ECM 2.416,1.4 2.781,1.562 0.365,0.162 10 THA 2.416,1.867 2.781,2.029 0.365,0.162 10 E2

Disconnect the mass air flow meter connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.


e.

Read the value.

OK:

-40°C (-40°F)




OK

10.REPLACE MASS AIR FLOW METER

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.

A385076E03
1.688,0.854 2.135,1.104 0.448,0.25 4.208,0.833 4.656,1.083 0.448,0.25 5.083,0.823 5.531,1.073 0.448,0.25 1.74,2.156 2.073,1.688 true 4.729,2.219 4.438,1.75 true 0.823,0.094 3.125,0.479 2.302,0.385 10 false Front view of wire harness connector: (to Mass Air Flow Meter) 1.771,0.906 2.156,1.104 0.385,0.198 10 false C50 1.458,2.188 1.844,2.385 0.385,0.198 10 false THA 3.802,0.083 6.104,0.469 2.302,0.385 10 false Front view of wire harness connector: (to ECM) 4.302,0.875 4.688,1.073 0.385,0.198 10 false C45 5.188,0.865 5.573,1.063 0.385,0.198 10 false C46 4.688,0.76 4.938,0.958 0.25,0.198 10 false *1 5.563,0.75 5.813,0.948 0.25,0.198 10 false *2 4.688,2.271 5.438,2.458 0.75,0.188 10 false 71 (THA) 0.135,2.052 0.938,2.26 0.802,0.208 10 false *1: for LHD 0.135,2.385 0.938,2.594 0.802,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C50-4 (THA) or C45-71 (THA) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C50-4 (THA) or C46-71 (THA) - Body ground Always 10 kΩ or higher




OK

6.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE MASS AIR FLOW METER

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END