Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0115  Engine Coolant Temperature Circuit  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor and it changes its resistance value according to the engine coolant temperature.

The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.

HINT:

If DTC P0115, P0117 or P0118 is stored, the ECM operates the fail-safe function in which the ECT is assumed to be 80°C (176°F).


P0115
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open or short in the engine coolant temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in engine coolant temperature (ECT) sensor circuit

·

ECT sensor

·

ECM



P0117
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Short in the ECT sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in ECT sensor circuit

·

ECT sensor

·

ECM



P0118
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open in the ECT sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in ECT sensor circuit

·

ECT sensor

·

ECM



Related Data List
DTC No. Data List
P0115 Coolant Temp
P0117
P0118

HINT:
·

If DTC P0115, P0117and/or P0118 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P0115, P0117 and/or P0118 is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine / Data List / Coolant Temp.

Reference:
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



WIRING DIAGRAM

A165735E06
0.643,2.502 0.945,2.658 0.302,0.156 10 C71 0.409,3.141 1.165,3.318 0.755,0.177 10 *1: for LHD 0.409,3.417 1.165,3.594 0.755,0.177 10 *2: for RHD 0.643,2.649 2.938,2.812 2.295,0.163 10 Engine Coolant Temperature Sensor 2.462,1.839 2.624,2.005 0.163,0.166 10 1 2.462,1.215 2.624,1.381 0.163,0.166 10 2 5.246,1.839 5.490,2.005 0.245,0.166 10 75 5.246,1.215 5.496,1.381 0.250,0.166 10 76 5.554,1.006 5.908,1.172 0.354,0.166 10 THW 6.24,0.56 6.500,0.726 0.260,0.166 10 5 V 6.163,0.908 6.319,1.074 0.156,0.166 10 R 5.713,2.664 6.608,2.830 0.895,0.166 10 C45*1, C46*2 5.713,2.839 6.067,3.005 0.354,0.166 10 ECM 5.554,1.643 5.908,1.810 0.354,0.166 10 E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are stored, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.


d.

Read the value.

OK:

75 to 90°C (167 to 194°F) with warm engine.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
75 to 90°C (167 to 194°F) C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F) or more.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the engine coolant temperature (ECT) sensor connector.

A385100E01
5.031,0.771 5.458,1.031 0.427,0.26 0.76,1.865 1.604,2.052 0.844,0.188 10 false ECT Sensor 2.615,2.156 3.031,2.344 0.417,0.188 10 false ECM 2.479,1.708 2.896,1.896 0.417,0.188 10 false E2 2.49,1.302 2.906,1.49 0.417,0.188 10 false THW 4.229,0.104 6.542,0.458 2.313,0.354 10 false Front view of wire harness connector: (to ECT Sensor) 5.104,0.823 5.427,1.01 0.323,0.188 10 false C71


b.

Connect terminals 1 and 2 of the ECT sensor wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.


f.

Read the value.

OK:

140°C (284°F) or higher




OK

7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the ECT sensor connector.

A385101E01
1.646,0.792 2.073,1.063 0.427,0.271 4.073,0.833 4.5,1.104 0.427,0.271 4.854,0.823 5.281,1.094 0.427,0.271 4.365,2.24 4.781,1.781 true 5.281,2.25 4.844,1.781 true 0.625,0.073 2.938,0.438 2.313,0.365 10 false Front view of wire harness connector: (to ECT Sensor) 3.875,0.094 6.188,0.458 2.313,0.365 10 false Front view of wire harness connector: (to ECM) 1.729,0.833 2.188,1.031 0.458,0.198 10 false C71 4.156,0.885 4.615,1.083 0.458,0.198 10 false C45 4.531,0.719 4.75,0.917 0.219,0.198 10 false *1 4.958,0.875 5.417,1.073 0.458,0.198 10 false C46 5.302,0.719 5.521,0.917 0.219,0.198 10 false *2 4.177,2.25 4.76,2.448 0.583,0.198 10 false 75 (E2) 5.125,2.26 5.906,2.458 0.781,0.198 10 false 76 (THW) 0.219,1.896 1.125,2.094 0.906,0.198 10 false *1: for LHD 0.219,2.271 1.125,2.469 0.906,0.198 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C71-2 - C45-76 (THW) Always Below 1 Ω
C71-1 - C45-75 (E2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C71-2 - C46-76 (THW) Always Below 1 Ω
C71-1 - C46-75 (E2) Always Below 1 Ω




OK

9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A166688E02
0.257,2.319 1.094,2.487 0.836,0.168 10 ECT Sensor 2.629,2.319 3.000,2.482 0.371,0.163 10 ECM 2.416,1.4 2.781,1.562 0.365,0.162 10 THW 2.416,1.867 2.781,2.029 0.365,0.162 10 E2

Disconnect the ECT sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.


e.

Read the value.

OK:

-40°C (-40°F)




OK

10.REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the ECT sensor connector.

A385101E02
1.646,0.792 2.073,1.063 0.427,0.271 4.073,0.833 4.5,1.104 0.427,0.271 4.854,0.823 5.281,1.094 0.427,0.271 5.281,2.25 4.844,1.781 true 0.625,0.073 2.938,0.438 2.313,0.365 10 false Front view of wire harness connector: (to ECT Sensor) 3.875,0.094 6.188,0.458 2.313,0.365 10 false Front view of wire harness connector: (to ECM) 1.729,0.833 2.188,1.031 0.458,0.198 10 false C71 4.156,0.885 4.615,1.083 0.458,0.198 10 false C45 4.531,0.719 4.75,0.917 0.219,0.198 10 false *1 4.958,0.875 5.417,1.073 0.458,0.198 10 false C46 5.302,0.719 5.521,0.917 0.219,0.198 10 false *2 5.125,2.26 5.906,2.458 0.781,0.198 10 false 76 (THW) 0.219,1.896 1.125,2.094 0.906,0.198 10 false *1: for LHD 0.219,2.271 1.125,2.469 0.906,0.198 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C71-2 or C45-76 (THW) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C71-2 or C46-76 (THW) - Body ground Always 10 kΩ or higher




OK

6.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END