Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

P0560
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECU are initialized (1 trip detection logic).
·

Open in back up power source circuit (to BATT terminal)

·

Battery

·

Battery terminals

·

EFI MAIN fuse

·

ECM



Related Data List
DTC No. Data List
P0560 Battery Voltage

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly erased.


WIRING DIAGRAM

A263485E01
0.561,4.845 1.078,5.025 0.517,0.180 10 Battery 2.992,4.978 3.790,5.158 0.798,0.180 10 *1: for LHD 2.992,5.272 3.790,5.453 0.798,0.180 10 *2: for RHD 2.936,1.418 3.186,1.577 0.250,0.159 10 1B 2.743,1.418 2.914,1.577 0.171,0.159 10 1 3.527,3.014 3.792,3.173 0.265,0.159 10 EFI 2.512,3.694 4.216,3.874 1.703,0.180 10 Engine Room Relay Block 2.322,2.281 2.988,2.440 0.666,0.159 10 EFI MAIN 5.827,0.694 6.154,0.848 0.326,0.154 10 20*2 5.864,0.86 6.144,1.032 0.280,0.172 10 A52 6.207,0.707 6.588,0.879 0.381,0.172 10 BATT 5.864,2.14 6.144,2.311 0.280,0.172 10 A52 6.207,2.14 6.425,2.312 0.218,0.172 10 +B 5.864,2.705 6.144,2.877 0.280,0.172 10 A52 5.518,0.694 5.841,0.848 0.323,0.154 10 20*1 5.533,0.86 5.813,1.032 0.280,0.172 10 A38 5.561,1.974 5.810,2.128 0.249,0.154 10 2*1 5.88,1.974 6.129,2.128 0.249,0.154 10 2*2 5.533,2.14 5.813,2.311 0.280,0.172 10 A38 5.512,2.539 5.827,2.693 0.315,0.154 10 44*1 5.852,2.539 6.168,2.693 0.315,0.154 10 44*2 5.533,2.705 5.813,2.877 0.280,0.172 10 A38 4.678,1.974 4.823,2.128 0.145,0.154 10 4 4.635,2.151 4.883,2.323 0.248,0.172 10 1B 1.983,1.974 2.128,2.128 0.145,0.154 10 1 1.939,2.14 2.188,2.311 0.248,0.172 10 1C 4.686,2.535 4.847,2.689 0.161,0.154 10 2 4.639,2.701 4.883,2.873 0.244,0.172 10 1B 1.989,2.539 2.149,2.693 0.161,0.154 10 3 1.942,2.705 2.186,2.877 0.244,0.172 10 1B 6.207,2.705 6.647,2.877 0.440,0.172 10 MREL 6.395,4.788 6.787,4.959 0.392,0.172 10 ECM 5.849,3.655 6.195,3.809 0.346,0.154 10 81*2 5.864,3.813 6.144,3.985 0.280,0.172 10 C46 5.518,3.655 5.864,3.809 0.346,0.154 10 81*1 5.533,3.813 5.812,3.985 0.280,0.172 10 C45 6.207,3.813 6.443,3.985 0.236,0.172 10 E1

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When the ignition switch is ON, even though +B voltage is present, when the voltage at terminal BATT (power supply for maintaining memorized values in the ECM) drops excessively, a DTC is stored.



PROCEDURE

1.INSPECT FUSE (EFI MAIN)
A162283E03
0.044,0.021 1.787,0.191 1.743,0.170 10 Engine Room Relay Block: 1.335,2.777 1.972,2.933 0.637,0.156 10 EFI MAIN 1.161,1.115 1.617,2.777 false

a.

Remove the EFI MAIN fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN Fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - ECM, BATTERY)

NG

7.CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
2.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - ECM, BATTERY)
A385194E01
4.833,1.323 5.271,1.604 0.438,0.281 5.604,1.313 6.042,1.594 0.438,0.281 5.74,2.948 5.25,2.219 true 0.531,0.188 2.854,0.552 2.323,0.365 10 false Front view of wire harness connector: (to Engine Room Relay Block) 2.083,1.323 2.823,1.521 0.74,0.198 10 false EFI MAIN 4.24,0.219 6.563,0.583 2.323,0.365 10 false Front view of wire harness connector: (to ECM) 4.906,1.385 5.26,1.583 0.354,0.198 10 false A38 5.698,1.365 6.052,1.563 0.354,0.198 10 false A52 5.292,1.219 5.563,1.417 0.271,0.198 10 false *1 6.083,1.229 6.354,1.427 0.271,0.198 10 false *2 3.823,2.896 4.656,3.094 0.833,0.198 10 false *1: for LHD 3.823,3.229 4.656,3.427 0.833,0.198 10 false *2: for RHD 5.656,3.01 6.49,3.208 0.833,0.198 10 false 20 (BATT)

a.

Check the harness and the connector between the EFI MAIN fuse and ECM.

i.

Remove the EFI MAIN fuse from the engine room relay block.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
EFI MAIN fuse (2) - A38-20 (BATT) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
EFI MAIN fuse (2) - A52-20 (BATT) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
EFI MAIN fuse (2) or A38-20 (BATT) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
EFI MAIN fuse (2) or A52-20 (BATT) - Body ground Always 10 kΩ or higher




b.

Check the harness and the connector between the EFI MAIN fuse and battery.

i.

Remove the EFI MAIN fuse from the engine room relay block.


ii.

Disconnect the cable from the positive (+) battery terminal.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Battery positive terminal - EFI MAIN fuse (1) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Battery positive terminal or EFI MAIN fuse (1) - Body ground Always 10 kΩ or higher





OK

3.INSPECT BATTERY

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.




OK

4.CHECK BATTERY TERMINAL

NG

9.REPLACE BATTERY
4.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

5.CHECK WHETHER DTC OUTPUT RECURS

NG

10.REPAIR OR REPLACE BATTERY TERMINAL
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON for 3 seconds.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Result Proceed to
P0560 is output A
No DTC is output B



A

6.REPLACE ECM

B

END

6.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE BATTERY

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE BATTERY TERMINAL

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 3 seconds.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END