Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  P0407  Exhaust Gas Recirculation Sensor "B" Circuit Low  P0408  Exhaust Gas Recirculation Sensor "B" Circuit High  


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.

P0405
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds No. 1 EGR valve position sensor output voltage is less than 0.1 V for 5 seconds (1 trip detection logic).
·

Open in No. 1 EGR valve position sensor circuit

·

No. 1 EGR valve (EGR valve position sensor)

·

ECM



P0406
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds No. 1 EGR valve position sensor output voltage is more than 4.9 V for 5 seconds (1 trip detection logic).
·

Short in No. 1 EGR valve position sensor circuit

·

No. 1 EGR valve (EGR valve position sensor)

·

ECM



P0407
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds No. 2 EGR valve position sensor output voltage is less than 0.1 V for 5 seconds (1 trip detection logic).
·

Open in No. 2 EGR valve position sensor circuit

·

No. 2 EGR valve (EGR valve position sensor)

·

ECM



P0408
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds No. 2 EGR valve position sensor output voltage is more than 4.9 V for 5 seconds (1 trip detection logic).
·

Short in No. 2 EGR valve position sensor circuit

·

No. 2 EGR valve (EGR valve position sensor)

·

ECM



MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Data List items "EGR Lift Sensor Volt %" and "EGR Lift Sensor Volt % #2" are values calculated by converting the EGR position sensor output voltage of 0 to 5 V to a percentage from 0 to 100%.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
U162938E01
0.142,0.027 2.506,0.360 2.364,0.333 10 Front view of wire harness connector: (to EGR Valve) 1.276,2.628 1.522,2.826 0.246,0.198 10 E2 1.882,2.628 2.128,2.826 0.246,0.198 10 VC 1.512,1.04 1.695,1.216 0.184,0.177 10 *1 0.342,2.538 1.034,2.715 0.692,0.177 10 *1: No. 1 0.342,2.873 1.034,3.050 0.692,0.177 10 *2: No. 2 2.402,1.04 2.585,1.216 0.184,0.177 10 *2 1.486,2.199 1.395,2.628 false 1.775,2.207 1.955,2.615 false 1.068,1.109 1.377,1.285 0.309,0.177 10 C87 1.945,1.109 2.254,1.285 0.309,0.177 10 C88

Disconnect the EGR valve connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
No. 1
Tester Connection Switch Condition Specified Condition
C87-3 (VC) - C87-2 (E2) Ignition switch ON 4.5 to 5.5 V

No. 2
Tester Connection Switch Condition Specified Condition
C88-3 (VC) - C88-2 (E2) Ignition switch ON 4.5 to 5.5 V




OK

2.INSPECT EGR VALVE ASSEMBLY (No. 1 or No. 2) (POSITION SENSOR)

NG

3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
2.INSPECT EGR VALVE ASSEMBLY (No. 1 or No. 2) (POSITION SENSOR)
A165764E03
0.154,0.182 2.690,0.528 2.536,0.346 10 Component without harness connected: (EGR Valve) 0.421,1.321 0.986,1.485 0.566,0.164 10 EGLS*1 0.421,1.539 0.986,1.703 0.566,0.164 10 EGS2*2 0.535,2.598 1.173,2.762 0.637,0.164 10 *1: No. 1 0.535,2.926 1.173,3.090 0.637,0.164 10 *2: No. 2 2.468,2.502 2.687,2.666 0.219,0.164 10 E2 2.406,1.343 2.693,1.506 0.287,0.164 10 VC 1.429,2.015 1.126,1.508 false 2.046,2.121 2.407,2.557 false 1.787,2.067 2.363,1.445 false

a.

Disconnect the EGR valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
No. 1
Tester Connection Condition Specified Condition
3 (VC) - 2 (E2) 20°C (68°F) 2.45 to 4.55 kΩ
4 (EGLS) - 2 (E2) 20°C (68°F) 2.45 to 4.55 kΩ

No. 2
Tester Connection Condition Specified Condition
3 (VC) - 2 (E2) 20°C (68°F) 2.45 to 4.55 kΩ
4 (EGS2) - 2 (E2) 20°C (68°F) 2.45 to 4.55 kΩ




OK

3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)

NG

5.REPLACE EGR VALVE ASSEMBLY (No. 1 or No. 2)
3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
a.

Disconnect the EGR valve connector.

A385184E02
1.25,0.927 1.667,1.188 0.417,0.26 1.958,0.927 2.375,1.188 0.417,0.26 4.198,0.896 4.615,1.156 0.417,0.26 4.875,0.885 5.292,1.146 0.417,0.26 1.896,1.719 2,2.01 true 4.073,1.865 4.073,1.031 4.073,1.031 3.917,1.031 true 3.844,1.875 3.729,2.313 true 1.74,1.729 1.51,1.948 true 2.063,1.74 2.271,1.948 true 3.906,1.885 4.49,2.479 true 3.979,1.875 4.906,2.302 true 0.729,0.156 3.073,0.51 2.344,0.354 10 false Front view of wire harness connector: (to EGR Valve) 3.698,0.104 6.042,0.458 2.344,0.354 10 false Front view of wire harness connector: (to EGR Valve) 1.333,0.969 1.677,1.146 0.344,0.177 10 false C87 2.042,0.969 2.385,1.146 0.344,0.177 10 false C88 1.688,0.844 1.958,1.052 0.271,0.208 10 false *1 2.406,0.844 2.677,1.052 0.271,0.208 10 false *2 1.281,1.917 1.521,2.094 0.24,0.177 10 false E2 3.365,2.354 4.125,2.552 0.76,0.198 10 false 87 (EEGL) 4.958,2.271 5.938,2.469 0.979,0.198 10 false 89 (EGLS*1) 0.115,2.156 0.844,2.354 0.729,0.198 10 false *1: No. 1 0.125,2.448 0.854,2.646 0.729,0.198 10 false *2: No. 2 0.875,2.167 1.604,2.365 0.729,0.198 10 false *3: for LHD 0.875,2.427 1.656,2.625 0.781,0.198 10 false *4: for RHD 4.26,0.938 4.604,1.115 0.344,0.177 10 false C45 4.938,0.938 5.281,1.115 0.344,0.177 10 false C46 4.646,0.802 4.917,1.01 0.271,0.208 10 false *3 5.323,0.802 5.594,1.01 0.271,0.208 10 false *4 1.927,2.031 2.208,2.208 0.281,0.177 10 false VC 2.26,1.979 2.844,2.156 0.583,0.177 10 false EGLS*1 2.26,2.156 2.844,2.333 0.583,0.177 10 false EGS2*2 4.219,2.5 5.24,2.688 1.021,0.188 10 false 88 (EGS2*2) 3.177,0.927 3.938,1.125 0.76,0.198 10 false 90 (VCEG)


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 1 (LHD)
Tester Connection Condition Specified Condition
C87-3 (VC) - C45-90 (VCEG) Always Below 1 Ω
C87-4 (EGLS) - C45-89 (EGLS) Always Below 1 Ω
C87-2 (E2) - C45-87 (EEGL) Always Below 1 Ω

No. 2 (LHD)
Tester Connection Condition Specified Condition
C88-3 (VC) - C45-90 (VCEG) Always Below 1 Ω
C88-4 (EGS2) - C45-88 (EGS2) Always Below 1 Ω
C88-2 (E2) - C45-87 (EEGL) Always Below 1 Ω

No. 1 (RHD)
Tester Connection Condition Specified Condition
C87-3 (VC) - C46-90 (VCEG) Always Below 1 Ω
C87-4 (EGLS) - C46-89 (EGLS) Always Below 1 Ω
C87-2 (E2) - C46-87 (EEGL) Always Below 1 Ω

No. 2 (RHD)
Tester Connection Condition Specified Condition
C88-3 (VC) - C46-90 (VCEG) Always Below 1 Ω
C88-4 (EGS2) - C46-88 (EGS2) Always Below 1 Ω
C88-2 (E2) - C46-87 (EEGL) Always Below 1 Ω


Standard Resistance (Check for Short):
No. 1 (LHD)
Tester Connection Condition Specified Condition
C87-3 (VC) or C45-90 (VCEG) - Body ground Always 10 kΩ or higher
C87-4 (EGLS) or C45-89 (EGLS) - Body ground Always 10 kΩ or higher

No. 2 (LHD)
Tester Connection Condition Specified Condition
C88-3 (VC) or C45-90 (VCEG) - Body ground Always 10 kΩ or higher
C88-4 (EGS2) or C45-88 (EGS2) - Body ground Always 10 kΩ or higher

No. 1 (RHD)
Tester Connection Condition Specified Condition
C87-3 (VC) or C46-90 (VCEG) - Body ground Always 10 kΩ or higher
C87-4 (EGLS) or C46-89 (EGLS) - Body ground Always 10 kΩ or higher

No. 2 (RHD)
Tester Connection Condition Specified Condition
C88-3 (VC) or C46-90 (VCEG) - Body ground Always 10 kΩ or higher
C88-4 (EGS2) or C46-88 (EGS2) - Body ground Always 10 kΩ or higher




OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE EGR VALVE ASSEMBLY (No. 1 or No. 2)
a.

Replace the EGR valve assembly (No. 1 or No. 2) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 5 seconds.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END