Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0105  Manifold Absolute Pressure / Barometric Pressure Circuit  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

A006532E19
0.385,0.49 0.521,0.688 0.135,0.198 10 false V 0.188,0.813 0.573,1.01 0.385,0.198 10 false 3.586 0.188,1.885 0.594,2.083 0.406,0.198 10 false 0.386 1.021,2.302 1.208,2.469 0.188,0.167 10 false 40 2.313,2.302 2.594,2.469 0.281,0.167 10 false 320 2.885,2.052 3.229,2.396 0.344,0.344 10 false kPa (abs) 2.885,2.531 3.406,2.74 0.521,0.208 10 false mmHg 2.885,2.875 3.375,3.073 0.49,0.198 10 false (in.Hg) 2.271,2.667 2.688,2.875 0.417,0.208 10 false 2400 0.948,2.667 1.302,2.844 0.354,0.177 10 false 300 1.365,3.083 2.167,3.26 0.802,0.177 10 false Air Pressure 0.917,2.823 1.375,3.031 0.458,0.208 10 false (11.8) 2.26,2.823 2.76,3.031 0.5,0.208 10 false (94.5)

The manifold absolute pressure sensor detects the intake manifold pressure by using its built-in sensor unit. The ECM determines the basic injection duration and injection advance timing based on the voltage output by the manifold absolute pressure sensor.

The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]). As a result the ECM controls the air-fuel ratio at the proper level under any driving conditions.

P0105
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After engine is started, race engine for 1 second After the engine is started, condition (a) continues for more than 2.0 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 0.1 V or less, or 4.8 V or more.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



P0107
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After engine is started, race engine for 1 second After the engine is started, condition (a) continues for more than 2.0 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 0.1 V or less.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



P0108
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After engine is started, race engine for 1 second After engine is started, condition (a) continues for more than 2.0 seconds (1 trip detection logic):
(a) Manifold absolute pressure sensor voltage is 4.8 V or more.
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



Related Data List
DTC No. Data List
P0105 MAP
P0107
P0108

HINT:
·

If DTC P0105, P0107 and/or P0108 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P0105, P0107 or P0108 is stored, check the intake manifold pressure by entering the following menus: Powertrain / Engine / Data List / MAP.

Reference
Intake Manifold Pressure Malfunction
Approximately 0 kPa
·

Open in VC circuit

·

Short in PIM circuit


250 kPa (1875 mmHg, 73.8 in.Hg) or higher
·

Open in PIM circuit

·

Open in E2 circuit





WIRING DIAGRAM

A165731E80
0.583,2.021 0.885,2.198 0.302,0.177 10 false C80 3.458,2.188 4.208,2.365 0.75,0.177 10 false *1: for LHD 3.458,2.448 4.208,2.625 0.75,0.177 10 false *2: for RHD 0.583,2.198 2.823,2.375 2.24,0.177 10 false Manifold Absolute Pressure Sensor 5.802,2.021 6.781,2.208 0.979,0.188 10 false C45*1, C46*2 5.802,2.188 6.229,2.365 0.427,0.177 10 false ECM 1.583,1.594 1.74,1.74 0.156,0.146 10 false E 1.427,1.031 1.781,1.219 0.354,0.188 10 false PIM 1.448,0.469 1.771,0.667 0.323,0.198 10 false VC 5.698,1.573 5.927,1.719 0.229,0.146 10 false E2 5.698,1.031 6.146,1.198 0.448,0.167 10 false PIM 5.698,0.458 6.271,0.656 0.573,0.198 10 false VCPM 1.844,0.573 1.969,0.75 0.125,0.177 10 false 3 1.844,1.146 1.969,1.323 0.125,0.177 10 false 2 1.844,1.698 1.969,1.875 0.125,0.177 10 false 1 5.385,0.563 5.615,0.771 0.229,0.208 10 false 66 5.323,1.146 5.646,1.375 0.323,0.229 10 false 114 5.385,1.677 5.625,1.885 0.24,0.208 10 false 75

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are stored, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / MAP.


d.

Read the value.

OK:

Same value as the actual atmospheric pressure.


HINT:

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather (high atmospheric pressure, low atmospheric pressure).




OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.

A385083E01
1.833,0.958 2.281,1.229 0.448,0.271 4.073,0.875 4.521,1.146 0.448,0.271 4.917,0.865 5.365,1.135 0.448,0.271 3.5,2.25 3.917,1.833 true 4.344,2.427 4.052,1.979 true 4.885,2.26 4.552,1.833 true 0.667,0.135 3.198,0.51 2.531,0.375 10 false Front view of wire harness connector: (to Manifold Absolute Pressure Sensor) 3.583,0.135 5.948,0.51 2.365,0.375 10 false Front view of wire harness connector: (to ECM) 1.906,1.01 2.281,1.208 0.375,0.198 10 false C80 4.167,0.927 4.542,1.125 0.375,0.198 10 false C45 5.01,0.917 5.385,1.115 0.375,0.198 10 false C46 4.563,0.792 4.802,0.979 0.24,0.188 10 false *1 5.396,0.76 5.635,0.948 0.24,0.188 10 false *2 3.292,2.302 4.135,2.51 0.844,0.208 10 false 66 (VCPM) 4.094,2.458 4.938,2.667 0.844,0.208 10 false 114 (PIM) 4.74,2.271 5.333,2.469 0.594,0.198 10 false 75 (E2) 0.406,2 1.26,2.198 0.854,0.198 10 false *1: for LHD 0.396,2.354 1.25,2.552 0.854,0.198 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
C80-2 (PIM) - C45-114 (PIM) Always Below 1 Ω
C80-3 (VC) - C45-66 (VCPM) Always Below 1 Ω
C80-1 (E) - C45-75 (E2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C80-2 (PIM) - C46-114 (PIM) Always Below 1 Ω
C80-3 (VC) - C46-66 (VCPM) Always Below 1 Ω
C80-1 (E) - C46-75 (E2) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C80-2 (PIM) or C45-114 (PIM) - Body ground Always 10 kΩ or higher
C80-3 (VC) or C45-66 (VCPM) - Body ground Always 10 kΩ or higher
C80-1 (E) or C45-75 (E2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C80-2 (PIM) or C46-114 (PIM) - Body ground Always 10 kΩ or higher
C80-3 (VC) or C46-66 (VCPM) - Body ground Always 10 kΩ or higher
C80-1 (E) or C46-75 (E2) - Body ground Always 10 kΩ or higher




OK

3.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
U162933E01
0.177,0.193 2.633,0.567 2.456,0.374 10 Front view of wire harness connector: (to Manifold Absolute Pressure Sensor) 1.592,1.251 1.908,1.409 0.315,0.158 10 C80 1.109,2.638 1.305,2.796 0.196,0.158 10 E 2.188,2.638 2.449,2.796 0.261,0.158 10 VC 1.502,2.162 1.209,2.607 false 1.963,2.175 2.301,2.624 false

Disconnect the manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C80-3 (VC) - C80-1 (E) Ignition switch ON 4.5 to 5.5 V




OK

4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

6.REPLACE ECM
4.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the tester on.


e.

After the engine is started, race the engine for 1 second.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result:
Display (DTC output) Proceed to
P0105, P0107 and/or P0108 A
No output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 3 seconds and turn the tester on.


e.

After the engine is started, race the engine for 1 second.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P0105, P0107 and/or P0108.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, race the engine for 1 minute and then idle the engine for 5 minutes.




NEXT

END