Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0087  Fuel Rail / System Pressure - Too Low  P0190  Fuel Rail Pressure Sensor Circuit  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the internal pressure to the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs the voltage in proportion to the internal fuel pressure.

A168838E01
1.13,0.857 2.352,1.026 1.222,0.170 10 Output Voltage (V) 3.284,2.243 4.648,2.435 1.364,0.192 10 Fuel Pressure (MPa) 3.202,1.914 3.323,2.063 0.121,0.149 10 0 3.391,1.914 3.596,2.070 0.205,0.155 10 30 3.812,1.914 4.002,2.077 0.191,0.163 10 90 4.324,1.914 4.619,2.077 0.295,0.163 10 180 4.582,1.914 4.877,2.077 0.295,0.163 10 190 2.675,1.338 2.928,1.501 0.253,0.163 10 1.0 2.596,1.181 2.929,1.343 0.333,0.163 10 1.48 2.596,0.892 2.911,1.062 0.316,0.170 10 2.44 2.596,0.479 2.911,0.635 0.316,0.156 10 3.88 2.596,0.315 2.918,0.485 0.323,0.170 10 4.04 0.071,0 1.603,0.170 1.532,0.170 10 Property Output Voltage

P0087
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After idling for 60 seconds, repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds Fuel pressure sensor output voltage stays at fixed value for 90 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail (for Bank 1))

·

ECM


HINT:

Breakdown points are electrically related only (pumps are not involved)



P0190
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or more for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail (for Bank 1))

·

ECM


HINT:

Breakdown points are electrically related only (pumps are not involved)



P0192
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail (for Bank 1))

·

ECM


HINT:

Breakdown points are electrically related only (pumps are not involved)



P0193
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Fuel pressure sensor output voltage is 4.9 V or more for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail (for Bank 1))

·

ECM


HINT:

Breakdown points are electrically related only (pumps are not involved)



Related Data List
DTC No. Data List
P0087
·

Fuel Press

·

Target Common Rail Pressure


P0190
P0192
P0193

HINT:
·

Check Fuel Press compared to Target Common Rail Pressure in the Data List by enter the following menus: Powertrain / Engine / Data List / Fuel Press, Target Common Rail Pressure. Under stable conditions, the difference between Fuel Press and Target Common Rail Pressure is within +/-5 MPa.

·

For more information on the fuel pressure sensor and common rail system, refer to the System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).

·

If DTC P0087 is stored, the following symptoms may appear:

-

Black smoke

-

Poor drivability

-

Lack of power


·

If DTC P0190, P0192 and/or P0193 is stored, the following symptoms may appear.

-

Lack of power due to accelerator restriction of fail-safe function




MONITOR DESCRIPTION

P0087 (Fuel pressure sensor output stays at fixed value):
·

Under normal conditions, the internal fuel pressure of the common rail usually fluctuates 1 to 2 MPa (10 to 20 kgf/cm2, 145 to 290 psi) even when the driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 27 to 37 MPa (275 to 377 kgf/cm2, 3915 to 5365 psi) when idling, and it increases to approximately 50 to 70 MPa (510 to 714 kgf/cm2, 7250 to 10150 psi) when running the engine at 2500 rpm.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned off.

·

The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.

U121330E01
0.058,0.035 1.904,0.244 1.846,0.208 10 P0087 Malfunction Detection 2.267,0.548 3.224,0.768 0.957,0.221 10 Fuel Pressure 4.848,1.68 5.518,1.883 0.671,0.203 10 Abnormal 5.646,0.447 6.226,0.648 0.579,0.201 10 Normal 2.295,2.17 3.244,2.378 0.949,0.209 10 Engine Speed 4.695,1.774 4.184,1.405 false 4.695,1.774 4.832,1.774 false 5.429,0.537 5.629,0.537 false 5.229,3.37 5.614,3.540 0.385,0.170 10 Time



P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):

These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.

If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.


WIRING DIAGRAM

A130470E05
0.565,3.242 1.957,3.443 1.392,0.201 10 Fuel Pressure Sensor 2.848,3.148 3.608,3.349 0.760,0.201 10 *1: for LHD 2.848,3.457 3.608,3.658 0.760,0.201 10 *2: for RHD 0.565,3.069 0.874,3.270 0.309,0.201 10 C82 1.834,1.072 2.076,1.273 0.243,0.201 10 VG 1.849,1.818 2.076,2.019 0.227,0.201 9 PR 1.879,2.565 2.077,2.766 0.197,0.201 10 E2 2.167,2.781 2.336,3.010 0.169,0.229 10 1 5.139,2.781 5.353,3.010 0.214,0.229 10 75 2.167,2.031 2.336,2.260 0.169,0.229 10 2 5.139,2.031 5.341,2.260 0.202,0.229 10 69 2.167,1.281 2.336,1.510 0.169,0.229 10 3 5.139,1.281 5.344,1.510 0.205,0.229 10 70 5.427,1.063 5.844,1.264 0.418,0.201 10 VCM 5.427,1.821 5.835,2.022 0.408,0.201 10 PCR1 5.427,2.57 5.733,2.771 0.306,0.201 10 E2 5.684,3.242 6.049,3.443 0.365,0.201 10 ECM 5.684,3.069 6.611,3.270 0.927,0.201 10 C45*1, C46*2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are stored, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / DTC.


d.

Read the DTCs.

Result
Display (DTC output) Proceed to
P0190, P0192, P0193 A
P0087 B



A

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

4.REPLACE FUEL PRESSURE SENSOR (COMMON RAIL (for Bank 1))
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.

A385061E01
1.656,0.906 2.083,1.156 0.427,0.25 4.073,0.865 4.5,1.115 0.427,0.25 5.031,0.844 5.458,1.094 0.427,0.25 1.344,2.208 1.708,1.781 true 1.865,2.208 1.875,1.792 true 2.5,2.198 2.052,1.781 true 4.052,2.25 4.344,1.792 true 4.698,2.281 4.396,1.792 true 5.052,2.281 4.75,1.792 true 0.792,0.125 3.135,0.5 2.344,0.375 10 false Front view of wire harness connector: (to Fuel Pressure Sensor) 3.823,0.115 6.167,0.49 2.344,0.375 10 false Front view of wire harness connector: (to ECM) 1.74,0.948 2.115,1.146 0.375,0.198 10 false C82 4.167,0.906 4.542,1.104 0.375,0.198 10 false C45 4.552,0.781 4.927,0.979 0.375,0.198 10 false *1 5.115,0.885 5.49,1.083 0.375,0.198 10 false C46 5.521,0.771 5.896,0.969 0.375,0.198 10 false *2 1.771,2.24 2.146,2.438 0.375,0.198 10 false PR 1.177,2.24 1.552,2.438 0.375,0.198 10 false E2 2.531,2.219 2.906,2.417 0.375,0.198 10 false VG 3.552,2.271 4.396,2.479 0.844,0.208 10 false 69 (PCR1) 4.406,2.344 5.25,2.552 0.844,0.208 10 false 70 (VCM) 5.156,2.281 6,2.49 0.844,0.208 10 false 75 (E2) 0.115,2.042 0.958,2.25 0.844,0.208 10 false *1: for LHD 0.115,2.385 0.958,2.594 0.844,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
C82-2 (PR) - C45-69 (PCR1) Always Below 1 Ω
C82-3 (VG) - C45-70 (VCM) Always Below 1 Ω
C82-1 (E2) - C45-75 (E2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C82-2 (PR) - C46-69 (PCR1) Always Below 1 Ω
C82-3 (VG) - C46-70 (VCM) Always Below 1 Ω
C82-1 (E2) - C46-75 (E2) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C82-2 (PR) or C45-69 (PCR1) - Body ground Always 10 kΩ or higher
C82-3 (VG) or C45-70 (VCM) - Body ground Always 10 kΩ or higher
C82-1 (E2) or C45-75 (E2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C82-2 (PR) or C46-69 (PCR1) - Body ground Always 10 kΩ or higher
C82-3 (VG) or C46-70 (VCM) - Body ground Always 10 kΩ or higher
C82-1 (E2) or C46-75 (E2) - Body ground Always 10 kΩ or higher




OK

3.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
U163034E01
0.339,0.02 2.680,0.362 2.341,0.341 10 Front view of wire harness connector: (to Fuel Pressure Sensor) 1.573,1.25 1.858,1.420 0.285,0.170 10 C82 1.029,2.718 1.259,2.888 0.230,0.170 10 E2 2.199,2.718 2.485,2.888 0.285,0.170 10 VG 1.937,2.17 2.206,2.715 false 1.529,2.164 1.204,2.718 false

a.

Disconnect the fuel pressure sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C82-3 (VG) - C82-1 (E2) Ignition switch ON 4.5 to 5.5 V




OK

4.REPLACE FUEL PRESSURE SENSOR (COMMON RAIL (for Bank 1))

NG

6.REPLACE ECM
4.REPLACE FUEL PRESSURE SENSOR (COMMON RAIL (for Bank 1))
a.

Replace the common rail (for bank 1) (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192, P0193)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192, P0193)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.



d.

Let the engine idle for 60 seconds, and then repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Read the DTCs.

Result
Result Proceed to
P0087, P0190, P0192 or P0193 is output A
No DTC is output B



A

6.REPLACE ECM

B

END

6.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Let the engine idle for 60 seconds, and then repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P0087, P0190, P0192 and/or P0193.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, increase idling time.




NEXT

END