Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  P213B  Exhaust Gas Recirculation Throttle Position Control (Range / Performance)  


DESCRIPTION

The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

P0488
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Over a period of 10 seconds or more, slowly raise engine speed to 3000 rpm and lower it The throttle motor activation duty is less than 10% or 90% or more for 30 seconds (1 trip detection logic).
HINT:

The throttle valve commanded duty can be read using the tester as the Data List item Throttle Motor Duty.


·

Throttle valve (for Bank 1) stuck

·

Throttle valve (for Bank 1) does not move smoothly

·

Open or short in throttle control motor (for Bank 1) circuit

·

ECM



P213B
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Over a period of 10 seconds or more, slowly raise engine speed to 3000 rpm and lower it The throttle motor activation duty is less than 10% or 90% or more for 30 seconds (1 trip detection logic).
HINT:

The throttle valve commanded duty can be read using the tester as the Data List item Throttle Motor Duty.


·

Throttle valve (for Bank 2) stuck

·

Throttle valve (for Bank 2) does not move smoothly

·

Open or short in throttle control motor (for Bank 2) circuit

·

ECM



Related Data List
DTC No. Data List
P0488
·

Throttle Motor Duty #1

·

Throttle Motor Duty #2

·

Actual Throttle Position

·

Actual Throttle Position #2


P213B

Reference
Condition Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm Throttle valve opening angle varies smoothly

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.

A128641E06
0.293,5.431 1.684,5.799 1.391,0.368 10 Duty Ratio Malfunction Counter 0.137,0.027 1.920,0.235 1.784,0.208 10 Malfunction Detection: 0.293,1.239 1.703,1.606 1.410,0.368 10 Throttle Valve Target Opening Angle 0.293,2.707 1.766,3.107 1.474,0.400 10 Throttle Valve Actual Opening Angle 0.949,4.117 1.684,4.333 0.736,0.215 10 Duty Ratio 4.797,1.709 5.389,1.910 0.593,0.201 10 Normal 4.797,2.475 5.547,2.676 0.750,0.201 10 Abnormal 4.797,3.98 5.389,4.181 0.593,0.201 10 Normal 4.797,3.215 5.547,3.416 0.750,0.201 10 Abnormal 5.95,0.557 6.400,0.758 0.450,0.201 10 Open 5.95,1.306 6.430,1.507 0.480,0.201 10 Close 5.95,2.017 6.400,2.218 0.450,0.201 10 Open 5.95,2.774 6.430,2.975 0.480,0.201 10 Close 5.95,3.516 6.464,3.720 0.514,0.203 10 100% 5.95,4.28 6.292,4.481 0.342,0.201 10 0% 3.368,5.26 4.788,5.467 1.421,0.207 10 Store P0488, P213B 5.348,5.238 6.143,5.449 0.795,0.211 10 Threshold 3.509,6.268 3.919,6.471 0.411,0.203 10 Time 4.614,2.111 4.74,1.795 false 4.614,2.87 4.74,2.554 false 4.614,3.616 4.74,3.3 false 4.74,4.076 4.614,3.76 false 5.347,5.23 5.165,5.009 false 3.333,5.35 3.096,5.176 false

WIRING DIAGRAM

A165769E12
0.708,0.792 2.042,0.99 1.333,0.198 10 false from EFI NO. 2 Fuse 0.708,3.354 2.042,3.552 1.333,0.198 10 false from EFI NO. 3 Fuse 2.865,0.896 3.031,1.042 0.167,0.146 10 false 2 4.271,0.906 4.438,1.052 0.167,0.146 10 false 1 5.802,0.906 6.052,1.083 0.25,0.177 10 false 42 3.073,0.802 3.427,0.979 0.354,0.177 10 false VCR 3.74,0.781 4.177,0.969 0.438,0.188 10 false VTAR 6.135,0.781 6.594,0.969 0.458,0.188 10 false LUSL 5.802,3.448 6.042,3.615 0.24,0.167 10 false 84 6.135,3.333 6.594,3.521 0.458,0.188 10 false LUS2 4.26,1.615 4.427,1.76 0.167,0.146 10 false 3 3.823,1.5 4.188,1.667 0.365,0.167 10 false E2R 2.833,1.854 3.146,2.01 0.313,0.156 10 false C85 2.833,2.052 4.979,2.208 2.146,0.156 10 false Throttle Control Motor (for Bank 1) 2.854,3.458 3.021,3.604 0.167,0.146 10 false 2 4.271,3.448 4.438,3.594 0.167,0.146 10 false 1 0.927,5 1.688,5.177 0.76,0.177 10 false *1: for LHD 0.927,5.292 1.688,5.469 0.76,0.177 10 false *2: for RHD 3.74,3.333 4.177,3.479 0.438,0.146 10 false VTAR 3.083,3.344 3.521,3.49 0.438,0.146 10 false VCR 4.271,4.146 4.438,4.292 0.167,0.146 10 false 3 3.813,4.052 4.167,4.208 0.354,0.156 10 false E2R 2.833,4.417 3.146,4.573 0.313,0.156 10 false C86 2.833,4.604 5.177,4.76 2.344,0.156 10 false Throttle Control Motor (for Bank 2) 6.031,5.24 6.938,5.417 0.906,0.177 10 false C45*1, C46*2 6.031,5.406 6.469,5.594 0.438,0.188 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:
·

Although the DTC titles say Exhaust Gas Recirculation Throttle Position Control Range / Performance, these DTCs relate to the throttle valve

·

After warming up the engine, DTC P0488 and P213B can be stored when 1 second or more passes after quickly accelerating the engine from idling.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)
a.
U162940E01
0.234,0.128 2.585,0.507 2.350,0.378 10 Front view of wire harness connector: (to Throttle Control Motor) 1.478,1.144 1.652,1.316 0.174,0.172 10 *1 0.062,2.601 0.945,2.773 0.883,0.172 10 *1: for Bank 1 0.062,2.952 0.941,3.124 0.879,0.172 10 *2: for Bank 2 2.375,2.885 2.737,3.057 0.362,0.172 10 VCR 2.372,1.144 2.546,1.316 0.174,0.172 10 *2 1.083,1.285 1.378,1.457 0.295,0.172 10 C85 1.971,1.294 2.266,1.466 0.295,0.172 10 C86 1.836,2.374 2.368,2.856 false

Disconnect the throttle control motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Bank 1
Tester Connection Switch Condition Specified Condition
C85-2 (VCR) - Body ground Ignition switch ON 11 to 14 V

for Bank 2
Tester Connection Switch Condition Specified Condition
C86-2 (VCR) - Body ground Ignition switch ON 11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - BATTERY)
2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.
U162941E01
0.234,0.128 2.585,0.507 2.350,0.378 10 Front view of wire harness connector: (to Throttle Control Motor) 1.478,1.144 1.652,1.316 0.174,0.172 10 *1 0.062,2.601 0.945,2.773 0.883,0.172 10 *1: for Bank 1 0.062,2.952 0.941,3.124 0.879,0.172 10 *2: for Bank 2 2.583,2.856 2.931,3.028 0.348,0.172 10 E2R 2.372,1.144 2.546,1.316 0.174,0.172 10 *2 2.088,2.345 2.523,2.813 false 1.083,1.285 1.378,1.457 0.295,0.172 10 C85 1.971,1.294 2.266,1.466 0.295,0.172 10 C86

Disconnect the throttle control motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Bank 1
Tester Connection Condition Specified Condition
C85-3 (E2R) - Body ground Always Below 1 Ω

for Bank 2
Tester Connection Condition Specified Condition
C86-3 (E2R) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
a.

Disconnect the throttle control motor connector.

A385191E01
1.177,0.844 1.583,1.104 0.406,0.26 1.948,0.844 2.354,1.104 0.406,0.26 4.281,0.802 4.688,1.063 0.406,0.26 5.042,0.792 5.448,1.052 0.406,0.26 1.344,1.885 1.583,1.729 true 4.729,2.177 5.302,1.51 true 5.615,2.156 5.458,1.698 true 0.615,0.115 2.917,0.479 2.302,0.365 10 false Front view of wire harness connector: (to Throttle Control Motor) 3.813,0.104 6.115,0.469 2.302,0.365 10 false Front view of wire harness connector: ((to ECM) 1.24,0.896 1.563,1.094 0.323,0.198 10 false C85 2.021,0.896 2.344,1.094 0.323,0.198 10 false C86 1.604,0.74 1.927,0.938 0.323,0.198 10 false *1 2.385,0.76 2.708,0.958 0.323,0.198 10 false *2 1.042,1.927 1.49,2.115 0.448,0.188 10 false VTAR 4.073,2.208 4.906,2.406 0.833,0.198 10 false 42 (LUSL*1) 5.417,2.177 6.323,2.375 0.906,0.198 10 false 84 (LUS2*2) 0.208,2.146 1.177,2.323 0.969,0.177 10 false *1: for Bank 1 0.198,2.427 1.167,2.604 0.969,0.177 10 false *2: for Bank 2 1.427,2.156 2.396,2.333 0.969,0.177 10 false *3: for LHD 1.438,2.427 2.406,2.604 0.969,0.177 10 false *4: for RHD 4.365,0.854 4.688,1.052 0.323,0.198 10 false C45 5.125,0.844 5.448,1.042 0.323,0.198 10 false C46 4.708,0.698 5.031,0.896 0.323,0.198 10 false *3 5.479,0.698 5.802,0.896 0.323,0.198 10 false *4


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Bank 1 (LHD)
Tester Connection Condition Specified Condition
C85-1 (VTAR) - C45-42 (LUSL) Always Below 1 Ω

for Bank 2 (LHD)
Tester Connection Condition Specified Condition
C86-1 (VTAR) - C45-84 (LUS2) Always Below 1 Ω

for Bank 1 (RHD)
Tester Connection Condition Specified Condition
C85-1 (VTAR) - C46-42 (LUSL) Always Below 1 Ω

for Bank 2 (RHD)
Tester Connection Condition Specified Condition
C86-1 (VTAR) - C46-84 (LUS2) Always Below 1 Ω


Standard Resistance (Check for Short):
for Bank 1 (LHD)
Tester Connection Condition Specified Condition
C85-1 (VTAR) or C45-42 (LUSL) - Body ground Always 10 kΩ or higher

for Bank 2 (LHD)
Tester Connection Condition Specified Condition
C86-1 (VTAR) or C45-84 (LUS2) - Body ground Always 10 kΩ or higher

for Bank 1 (RHD)
Tester Connection Condition Specified Condition
C85-1 (VTAR) or C46-42 (LUSL) - Body ground Always 10 kΩ or higher

for Bank 2 (RHD)
Tester Connection Condition Specified Condition
C86-1 (VTAR) or C46-84 (LUS2) - Body ground Always 10 kΩ or higher




OK

4.REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1 or Bank 2)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1 or Bank 2)
a.

Replace the diesel throttle body assembly (for Bank 1 or Bank 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS

b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Start the engine.


e.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Result Proceed to
P0488 and/or P213B is output A
No DTC is output B



A

6.REPLACE ECM

B

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - BATTERY)

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P0488 and/or P213B.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again and then idle the engine for 5 minutes.




NEXT

END