Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  P213B  Exhaust Gas Recirculation Throttle Position Control (Range / Performance)  


DESCRIPTION

The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

P0488 (Bank 1), P213B (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state. Target and actual opening angle of the throttle valve differs for approximately 20 seconds.
(1 trip detection logic)
·

Throttle valve stuck

·

Throttle valve does not move smoothly

·

Open or short in throttle control motor circuit

·

ECM


The throttle motor activation duty exceeds the threshold for 0.5 seconds a certain number of times (40 seconds or more).
(1 trip detection logic)

Related Data List
DTC No. Data List
P0488
·

Throttle Motor Duty

·

Actual Throttle Position


P213B
·

Throttle Motor Duty #2

·

Actual Throttle Position #2



Reference
Condition Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm Throttle valve opening angle varies smoothly

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.

A128641E11
0.293,5.431 1.684,5.799 1.391,0.368 10 Duty Ratio Malfunction Counter 0.137,0.027 1.920,0.235 1.784,0.208 10 Malfunction Detection: 0.293,1.239 1.703,1.606 1.410,0.368 10 Throttle Valve Target Opening Angle 0.293,2.707 1.766,3.107 1.474,0.400 10 Throttle Valve Actual Opening Angle 0.949,4.117 1.684,4.333 0.736,0.215 10 Duty Ratio 4.797,1.709 5.389,1.910 0.593,0.201 10 Normal 4.797,2.475 5.547,2.676 0.750,0.201 10 Abnormal 4.797,3.98 5.389,4.181 0.593,0.201 10 Normal 4.797,3.215 5.547,3.416 0.750,0.201 10 Abnormal 5.95,0.557 6.400,0.758 0.450,0.201 10 Open 5.95,1.306 6.430,1.507 0.480,0.201 10 Close 5.95,2.017 6.400,2.218 0.450,0.201 10 Open 5.95,2.774 6.430,2.975 0.480,0.201 10 Close 5.95,3.516 6.464,3.720 0.514,0.203 10 100% 5.95,4.28 6.292,4.481 0.342,0.201 10 0% 3.368,5.26 5.004,5.467 1.636,0.207 10 Stores P0488 or P213B 5.348,5.238 6.143,5.449 0.795,0.211 10 Threshold 3.509,6.268 3.919,6.471 0.411,0.203 10 Time 4.614,2.111 4.74,1.795 false 4.614,2.87 4.74,2.554 false 4.614,3.616 4.74,3.3 false 4.74,4.076 4.614,3.76 false 5.347,5.23 5.165,5.009 false 3.333,5.35 3.096,5.176 false

WIRING DIAGRAM

A165769E11
0.667,0.802 2.063,1 1.396,0.198 10 false from EFI NO. 2 Fuse 2.854,0.906 3.021,1.052 0.167,0.146 10 false 2 4.25,0.906 4.417,1.052 0.167,0.146 10 false 1 5.75,0.906 6.021,1.115 0.271,0.208 10 false 57 3.083,0.802 3.51,1 0.427,0.198 10 false VCR 3.677,0.802 4.167,0.979 0.49,0.177 10 false VTAR 6.135,0.802 6.594,0.948 0.458,0.146 10 false LUSL 5.792,3.458 6.042,3.625 0.25,0.167 10 false 56 6.135,3.344 6.594,3.49 0.458,0.146 10 false LUS2 4.25,1.594 4.417,1.74 0.167,0.146 10 false 3 3.781,1.5 4.146,1.677 0.365,0.177 10 false E2R 2.833,1.854 3.146,2.01 0.313,0.156 10 false C85 2.833,2.052 5.073,2.281 2.24,0.229 10 false Throttle Control Motor (for Bank 1) 2.875,3.458 3.042,3.604 0.167,0.146 10 false 2 4.26,3.469 4.427,3.615 0.167,0.146 10 false 1 3.083,3.354 3.427,3.5 0.344,0.146 10 false VCR 3.74,3.354 4.177,3.5 0.438,0.146 10 false VTAR 4.26,4.156 4.427,4.302 0.167,0.146 10 false 3 3.833,4.042 4.177,4.229 0.344,0.188 10 false E2R 2.833,4.417 3.146,4.573 0.313,0.156 10 false C86 2.833,4.604 5.167,4.823 2.333,0.219 10 false Throttle Control Motor (for Bank 2) 6.104,5.271 6.979,5.448 0.875,0.177 10 false C45*1, C46*2 6.094,5.438 6.531,5.625 0.438,0.188 10 false ECM 0.677,3.333 2.083,3.531 1.406,0.198 10 false from EFI NO. 3 Fuse 0.74,4.917 2.146,5.115 1.406,0.198 10 false *1: for LHD 0.74,5.26 1.573,5.458 0.833,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:
·

Although the DTC titles say "exhaust gas recirculation throttle position control range / performance", these DTCs relate to the throttle valve

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Active Test / Diesel Throttle Target Angle or Diesel Throttle Target Angle #2.


d.

While continuously changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that "Actual Throttle Position" or "Actual Throttle Position #2" smoothly changes to the set opening amount.

OK:

Value smoothly changes to set opening amount.




OK

5.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)
a.
U162833E01
0.12,0.026 0.331,0.189 0.211,0.163 10 *a 0.184,0.81 0.478,0.979 0.294,0.170 10 C85 1.568,1.912 1.914,2.082 0.346,0.170 10 VCR 1.756,1.446 1.756,1.895 false 0.18,1.467 0.474,1.637 0.294,0.170 10 C86 0.683,0.782 0.894,0.945 0.211,0.163 10 *A 0.683,1.461 0.894,1.624 0.211,0.163 10 *B

Disconnect the throttle control motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C85-2 (VCR) - Body ground Ignition switch ON 11 to 14 V
C86-2 (VCR) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Throttle Control Motor)


c.

Reconnect the throttle control motor connector.



OK

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Disconnect the throttle control motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C85-3 (E2R) - Body ground Always Below 1 Ω
C86-3 (E2R) - Body ground Always Below 1 Ω



c.

Reconnect the throttle control motor connector.



OK

4.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
a.

Disconnect the throttle control motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C85-1 (VTAR) - C45-57 (LUSL) Always Below 1 Ω
C86-1 (VTAR) - C45-56 (LUS2) Always Below 1 Ω
C85-1 (VTAR) or C45-57 (LUSL) - Body ground Always 10 kΩ or higher
C86-1 (VTAR) or C45-56 (LUS2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C85-1 (VTAR) - C46-57 (LUSL) Always Below 1 Ω
C86-1 (VTAR) - C46-56 (LUS2) Always Below 1 Ω
C85-1 (VTAR) or C46-57 (LUSL) - Body ground Always 10 kΩ or higher
C86-1 (VTAR) or C46-56 (LUS2) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle control motor connector.


e.

Reconnect the ECM connector.



OK

5.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
a.

Visually check for deposits in the diesel throttle body assembly. If there are deposits, clean the diesel throttle body assembly.



NEXT

6.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
6.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Active Test / Diesel Throttle Target Angle or Diesel Throttle Target Angle #2.


d.

While continuously changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that "Actual Throttle Position" or "Actual Throttle Position #2" smoothly changes to the set opening amount.

OK:

Value smoothly changes to set opening amount.




OK

8.CHECK WHETHER DTC OUTPUT RECURS

NG

7.REPLACE DIESEL THROTTLE BODY ASSEMBLY
7.REPLACE DIESEL THROTTLE BODY ASSEMBLY

When DTC P0488 is output:

·

Replace the diesel throttle body assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).


When DTC P213B is output:

·

Replace the diesel throttle body assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS

b.

Turn the ignition switch off and wait for 30 seconds.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Start the engine.


f.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Result
Result Proceed to
P0488 or P213B is output A
No DTC is output B



A

9.REPLACE ECM

B

END

9.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - INTEGRATION RELAY)
a.

Repair or replace the harness or connector.



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off and wait for 30 seconds.


d.

Start the engine.


e.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


ii.

Input DTC P0488 and P213B.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.




NEXT

END