Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0180  Fuel Temperature Sensor "A" Circuit  P0182  Fuel Temperature Sensor "A" Circuit Low Input  P0183  Fuel Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (See Fig. 1).

The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.

Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change in fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump assembly.

A208462E01
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

P0180
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor (fuel supply pump assembly)

·

ECM



P0182
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in fuel temperature sensor circuit

·

Fuel temperature sensor (fuel supply pump assembly)

·

ECM



P0183
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in fuel temperature sensor circuit

·

Fuel temperature sensor (fuel supply pump assembly)

·

ECM



Related Data List
DTC No. Data List
P0180
P0182
P0183
Fuel Temperature

HINT:

If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

Lack of power




WIRING DIAGRAM

A184084E10
2.063,1.01 2.375,1.177 0.313,0.167 10 false THF 2.469,1.229 2.646,1.406 0.177,0.177 10 false 2 2.135,1.604 2.375,1.771 0.24,0.167 10 false E2 5.563,1.01 5.875,1.177 0.313,0.167 10 false THF 6.25,0.625 6.563,0.792 0.313,0.167 10 false 5 V 5.552,1.635 5.792,1.802 0.24,0.167 10 false E2 6.177,0.906 6.333,1.073 0.156,0.167 10 false R 2.469,1.854 2.646,2.031 0.177,0.177 10 false 1 5.188,1.24 5.49,1.427 0.302,0.188 10 false 116 5.729,2.667 6.667,2.844 0.938,0.177 10 false C45*1, C46*2 5.729,2.844 6.146,3.021 0.417,0.177 10 false ECM 5.26,1.875 5.542,2.115 0.281,0.24 10 false 92 0.698,2.417 2.365,2.604 1.667,0.188 10 false Fuel Temperature Sensor 0.438,3 1.385,3.188 0.948,0.188 10 false *1: for LHD 0.438,3.292 1.385,3.479 0.948,0.188 10 false *2: for RHD 3.875,2.646 4.198,2.802 0.323,0.156 10 false zC1 0.688,2.219 1.01,2.375 0.323,0.156 10 false z65

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (FUEL TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Fuel Temperature.


d.

Read the value.

OK:

Same as the actual fuel temperature


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (Same as actual fuel temperature) C

HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

5.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
U163297E02
0.823,0.167 1.031,0.313 0.208,0.146 10 false *1 2.656,0.146 2.823,0.313 0.167,0.167 10 false *2 0.625,2.646 0.823,2.833 0.198,0.188 10 false *a 2.427,1.031 2.74,1.177 0.313,0.146 10 false THF 2.448,1.5 2.844,1.656 0.396,0.156 10 false E2 0.583,3.333 0.896,3.479 0.313,0.146 10 false z65

Disconnect the fuel temperature sensor connector.


b.

Connect terminals 2 and 1 of the fuel temperature sensor connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Engine and ECT / Data List / Fuel Temperature.


f.

Read the value.

OK:

140°C (284°F) or higher


Text in Illustration
*1 Fuel Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Fuel Temperature Sensor)


g.

Reconnect the fuel temperature sensor connector.



NG

3.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)

OK

6.REPLACE FUEL TEMPERATURE SENSOR
3.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
z65-2 (THF) - C45-116 (THF) Always Below 1 Ω
z65-1 (E2) - C45-92 (E2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
z65-2 (THF) - C46-116 (THF) Always Below 1 Ω
z65-1 (E2) - C46-92 (E2) Always Below 1 Ω



d.

Reconnect the fuel temperature sensor connector.


e.

Reconnect the ECM connector.



OK

4.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A204586E04
0.787,0.15 0.993,0.302 0.207,0.151 10 *1 2.618,0.122 2.786,0.289 0.167,0.167 10 *2 2.391,0.97 2.699,1.121 0.309,0.151 10 THF 2.425,1.438 2.817,1.594 0.392,0.156 10 E2

Disconnect the fuel temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Engine and ECT / Data List / Fuel Temperature.


e.

Read the value.

OK:

-40°C (-40°F)


Text in Illustration
*1 Fuel Temperature Sensor
*2 ECM


f.

Reconnect the fuel temperature sensor connector.



OK

6.REPLACE FUEL TEMPERATURE SENSOR

NG

7.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
6.REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL TEMPERATURE SENSOR>REMOVAL).



NEXT

9.BLEED AIR FROM FUEL SYSTEM
7.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
z65-2 (THF) or C45-116 (THF) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
z65-2 (THF) or C46-116 (THF) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel temperature sensor connector.


e.

Reconnect the ECM connector.



OK

8.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/o DPF)>ON-VEHICLE INSPECTION).

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.




NEXT

10.PERFORM SUPPLY PUMP INITIALIZATION
10.PERFORM SUPPLY PUMP INITIALIZATION

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch to ON for 1 second or more.


d.

Enter the following menus: Engine and ECT / Trouble Codes.


e.

Confirm that the DTC is not output again.



NEXT

END