Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P1495  Intake Air Temperature Sensor 1 Circuit  P1496  Intake Air Temperature Sensor 1 Circuit Low  P1497  Intake Air Temperature Sensor 1 Circuit High  


DESCRIPTION

A385085E01
1.417,2.042 1.688,1.625 1.688,1.625 1.823,1.625 false 0.198,0.094 1.427,0.292 1.229,0.198 10 false (Fig. 1) 0.177,0.469 1.406,0.667 1.229,0.198 10 false Resistance kΩ 1.26,4.115 2.698,4.323 1.438,0.208 10 false Temperature °C (°F) 1.875,1.521 2.719,1.719 0.844,0.198 10 false Acceptable

The Intake Air Temperature (IAT) sensor is built into the charge air cooler and senses the IAT. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the greater the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

P1495
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Open or short in the intake air temperature (IAT) sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in intake air temperature (IAT) sensor circuit

·

IAT sensor

·

ECM



P1496
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Short in the IAT sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in IAT sensor circuit

·

IAT sensor

·

ECM



P1497
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Open in the IAT sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in IAT sensor circuit

·

IAT sensor

·

ECM



Related Data List
DTC No. Data List
P1495 Intake Air Temp (Turbo)
P1496
P1497

HINT:

If DTC P1495, P1496 and/or P1497 is stored, the following symptoms may appear:


·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power


WIRING DIAGRAM

A165735E07
0.58,2.449 0.875,2.605 0.295,0.156 10 C79 0.58,2.608 2.592,2.838 2.012,0.230 10 Intake Air Temperature Sensor 0.854,3.036 1.599,3.212 0.745,0.176 10 *1: for LHD 0.854,3.31 1.599,3.485 0.745,0.176 10 *2: for RHD 5.735,2.673 6.641,2.829 0.906,0.156 10 C45*1, C46*2 5.735,2.832 6.090,3.006 0.355,0.174 10 ECM 2.457,1.837 2.581,2.012 0.123,0.174 10 1 5.54,1.646 5.772,1.820 0.233,0.174 10 E2 5.54,1.034 5.907,1.208 0.367,0.174 10 THIA 2.457,1.226 2.581,1.400 0.123,0.174 10 2 5.292,1.837 5.486,2.012 0.194,0.174 10 75 5.301,1.226 5.486,1.400 0.185,0.174 10 74 6.161,0.917 6.287,1.071 0.126,0.154 10 R 6.254,0.632 6.517,0.798 0.262,0.165 10 5V

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are stored, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE [TURBO])
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).


d.

Read the value.

OK:

Same as air temperature near intake manifold.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as air temperature near intake manifold) C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F) or more.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the intake air temperature (IAT) sensor connector.

A385264E01
5.01,0.865 5.427,1.135 0.417,0.271 0.958,1.813 1.75,2.01 0.792,0.198 10 false IAT Sensor 2.74,1.958 3.177,2.167 0.438,0.208 10 false ECM 2.635,1.229 3.073,1.438 0.438,0.208 10 false THIA 2.635,1.635 3.073,1.844 0.438,0.208 10 false E2 4.135,0.135 6.458,0.521 2.323,0.385 10 false Front view of wire harness connector: (to IAT Sensor) 5.094,0.917 5.531,1.125 0.438,0.208 10 false C79


b.

Connect terminals 1 and 2 of the IAT sensor wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).


f.

Read the value.

OK:

140°C (284°F) or higher




OK

7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the IAT sensor connector.

A385265E01
1.604,0.844 2.042,1.104 0.438,0.26 4.146,0.802 4.583,1.063 0.438,0.26 4.948,0.813 5.385,1.073 0.438,0.26 4.313,2.208 4.667,1.781 true 5.167,2.219 4.74,1.781 true 0.51,0.094 2.813,0.458 2.302,0.365 10 false Front view of wire harness connector: (to IAT Sensor) 3.823,0.104 6.125,0.469 2.302,0.365 10 false Front view of wire harness connector: (to ECM) 1.688,0.896 2.031,1.083 0.344,0.188 10 false C79 4.229,0.854 4.573,1.042 0.344,0.188 10 false C45 5.052,0.854 5.396,1.042 0.344,0.188 10 false C46 4.625,0.781 4.854,0.979 0.229,0.198 10 false *1 5.438,0.781 5.667,0.979 0.229,0.198 10 false *2 4.052,2.25 4.771,2.427 0.719,0.177 10 false 74 (THIA) 5.021,2.25 5.74,2.427 0.719,0.177 10 false 75 (E2) 0.281,1.979 1,2.156 0.719,0.177 10 false *1: for LHD 0.281,2.344 1,2.521 0.719,0.177 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
C79-2 - C45-74 (THIA) Always Below 1 Ω
C79-1 - C45-75 (E2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C79-2 - C46-74 (THIA) Always Below 1 Ω
C79-1 - C46-75 (E2) Always Below 1 Ω




OK

9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A166688E04
0.335,2.319 1.081,2.487 0.746,0.168 10 IAT Sensor 2.556,2.319 2.927,2.482 0.371,0.163 10 ECM 2.416,1.4 2.781,1.562 0.365,0.162 10 THIA 2.416,1.867 2.781,2.029 0.365,0.162 10 E2

Disconnect the IAT sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temp (Turbo).


e.

Read the value.

OK:

-40°C (-40°F)




OK

10.REPLACE INTAKE AIR TEMPERATURE SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the IAT sensor connector.

A385265E02
1.604,0.844 2.042,1.104 0.438,0.26 4.146,0.802 4.583,1.063 0.438,0.26 4.948,0.813 5.385,1.073 0.438,0.26 4.313,2.208 4.667,1.781 true 0.51,0.094 2.813,0.458 2.302,0.365 10 false Front view of wire harness connector: (to IAT Sensor) 3.823,0.104 6.125,0.469 2.302,0.365 10 false Front view of wire harness connector: (to ECM) 1.688,0.896 2.031,1.083 0.344,0.188 10 false C79 4.229,0.854 4.573,1.042 0.344,0.188 10 false C45 5.052,0.854 5.396,1.042 0.344,0.188 10 false C46 4.625,0.781 4.854,0.979 0.229,0.198 10 false *1 5.438,0.781 5.667,0.979 0.229,0.198 10 false *2 4.052,2.25 4.771,2.427 0.719,0.177 10 false 74 (THIA) 0.281,1.979 1,2.156 0.719,0.177 10 false *1: for LHD 0.281,2.344 1,2.521 0.719,0.177 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C79-2 or C45-74 (THIA) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C79-2 or C46-74 (THIA) - Body ground Always 10 kΩ or higher




OK

6.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR
a.


NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE INTAKE AIR TEMPERATURE SENSOR
a.


NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END