Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  Turbocharger Oil Leak and White Smoke  


DESCRIPTION

Oil Leak Type Description Main Trouble Area
Internal oil leak
(White smoke)
Oil leak from bearing housing to compressor housing (intake side) or turbine housing (exhaust side) through seal rings.
Internal oil leak is not visible from outside of turbocharger.
If oil leak occurs from turbine side seal, large amount of white smoke will be emitted from exhaust pipe.
·

Compressor side seal ring

·

Turbine side seal ring

·

Clogging of oil drain

·

Shaft breakage

·

Shaft and bearing seizure

·

Compressor impeller damage

·

Low quality fuel


External oil leak Oil leak from inside of turbocharger to outside of turbocharger (e.g. from FIPG seal, oil pipe flange or oil pipe union).
Includes oil leak visible from outside of turbocharger.
·

FIPG sealing part

·

Oil pipe flange

·

Oil pipe union

·

Hose connection of intake pipe



HINT:
·

Turbocharger oil leaks are classified into 2 types. One is an internal oil leak, and the other is an external oil leak.

·

Each part of the turbocharger is shown below.

·

When oil leaks and smoke occur, sometimes the turbocharger is mistakenly replaced, even though the turbocharger is not the cause of the problem.

·

When there are oil marks on the surface of the compressor housing, or oil in the compressor inlet or outlet, the problem may mistakenly be determined to be a turbocharger oil leak.



A229639E05
4.354,3.49 4.354,3.792 false 6.24,1.396 6.167,1.396 6.167,1.396 4.333,1.823 false 5.865,1.938 5.375,1.938 false 2.656,2.26 0.854,2.26 false 3.854,2.688 3.854,3.719 false 3.75,0.198 3.823,0.198 3.823,0.198 4.063,1.125 false 3.083,0.271 3.156,0.271 3.156,0.271 3.542,1.99 false 2.938,1.979 1.073,1.979 false 5.854,2.271 4.719,2.271 false 6,0.792 5.104,0.792 false 1.177,0.563 1.26,0.563 1.26,0.563 2.115,0.865 false 6.042,0.729 6.24,0.875 0.198,0.146 10 false *1 0.896,1.917 1.094,2.063 0.198,0.146 10 false *2 5.896,1.875 6.094,2.021 0.198,0.146 10 false *3 5.906,2.208 6.104,2.354 0.198,0.146 10 false *4 3.531,0.135 3.729,0.281 0.198,0.146 10 false *5 2.906,0.198 3.104,0.344 0.198,0.146 10 false *6 4.271,3.813 4.469,3.958 0.198,0.146 10 false *8 4.458,1.24 4.656,1.385 0.198,0.146 10 false *a 0.969,0.5 1.167,0.646 0.198,0.146 10 false *9 0.604,2.198 0.865,2.344 0.26,0.146 10 false *10 3.771,3.74 3.969,3.885 0.198,0.146 10 false *7 6.271,1.323 6.469,1.469 0.198,0.146 10 false *2 2.677,1.719 2.875,1.865 0.198,0.146 10 true *b 0.573,0.073 1.031,0.333 0.458,0.26 10 false *A 0.719,3.969 0.917,4.115 0.198,0.146 10 false *b 4.635,3.958 4.906,4.156 0.271,0.198 10 false *a

Text in Illustration
*A DC Motor Type Turbocharger (No. 1) - -
*1 Compressor Housing *2 Seal Ring
*3 Compressor Inlet *4 Compressor Impeller
*5 Bearing Housing *6 Turbine Shaft
*7 Oil Drain (Outlet) *8 FIPG Sealing Part
*9 Turbine Housing *10 Turbine Wheel
*a Internal oil leak to compressor housing *b Internal oil leak to turbine housing

A213994E07
0.167,0.115 0.563,0.427 0.396,0.313 10 true *A

Text in Illustration
*A Fig. 1 - -

HINT:
·

This illustration is not the turbocharger of the 1VD-FTV engine.

·

If the oil stain is similar to the one shown in the illustration (fig. 1), it may be oil spray from parts surrounding the turbocharger or oil leaking from the air cleaner hose. Therefore, this kind of oil stain on the outer surface of the turbocharger is not an oil leak from the turbocharger (external oil leak), and is not related to white smoke. For identification of an actual turbocharger outer oil leak, check only the sealing part shown below.



A216497E02
1.537,0.022 1.746,0.188 0.209,0.166 10 *A 4.738,0.036 4.968,0.202 0.23,0.166 10 *B 2.63,2.246 2.867,2.471 0.237,0.226 10 *a 5.743,0.38 5.959,0.566 0.216,0.186 10 *b 1.853,1.765 2.601,2.303 false 5.091,0.969 5.705,0.466 false

Text in Illustration
*A Fig. 2 *B Fig. 3
*a Oil Existence at Compressor Inlet (Max. 5 cm3) *b Oil Existence at Compressor Outlet

HINT:
·

This illustration is not the turbocharger of the 1VD-FTV engine.

·

A certain amount of oil is contained in the intake system because blow-by gas containing oil mist is returned to the intake system by the PCV. Therefore, the oil amount at the compressor inlet shown in the left figure (fig. 2) is normal and not an oil leak from the turbocharger (internal oil leak). Also, oil at the compressor outlet as shown in fig. 3 is normal.

·

For 1KD-FTV engines, only bank 2 has a PCV path. Therefore, the oil shown in fig. 2 only exists for the turbocharger sub-assembly (for bank 2) and not for the turbocharger sub-assembly (for bank 1).



A206068E01
0.066,0.013 0.315,0.207 0.249,0.193 10 *A 0.141,2.436 0.385,2.627 0.244,0.191 10 *a 0.418,0.01 0.63,0.203 0.212,0.193 10 *b 0.347,2.551 0.651,2.237 false

Text in Illustration
*A Fig. 4 - -
*a In the case of an actual oil leak, oil leaks from the sealed part *b Oil Leak Check Point (FIPG Sealing Part)

HINT:
·

This illustration is not the turbocharger of the 1VD-FTV engine.

·

This is an illustration (fig. 4) of an air leak test performed by applying soapy water to the area of the leak. Bubbles indicate the leak point.



Faults and Symptoms of Turbocharger Parts


Compressor Side Seal Ring
Main fault Seal ring breakage
Symptoms
·

Oil leak to compressor housing

·

Excessive oil consumption


Note
·

In case of compressor seal ring failure, large amount of oil would be found between compressor outlet and intercooler, and between intercooler and intake manifold, but not found at compressor inlet.

·

If large amount of oil is found at compressor inlet, it is not from turbocharger and may indicate a problem in the PCV system.



Turbine Side Seal Ring
Main fault Seal ring breakage
Symptoms
·

Oil leak to turbine housing

·

Large amount of white smoke from exhaust pipe

·

Excessive oil consumption


Note
·

In case of turbine seal ring failure, large amount of white smoke would be emitted continuously.

·

If white smoke is emitted only just after engine start (and it disappears later), or small amount of white smoke is emitted intermittently, it is not from turbocharger. It is due to failure of other parts.

·

If wet oil is found at turbine inlet, it is not from turbocharger. It is due to problem in other parts.



Bearing Housing (Oil Drain Clogging)
Main fault Oil drain clogging by coked oil
Symptoms Large amount of white smoke from exhaust pipe

HINT:
·

Oil coking is caused by insufficient oil maintenance.

·

If the oil drain is clogged by coked oil, oil cannot be drained smoothly, and it overflows from the bearing housing to the compressor housing and turbine housing. This results in a large amount of white smoke from the exhaust pipe.



A216499E08
1.833,1.438 2.698,2.115 false 6.125,2.073 4.865,1.813 false 1.74,1.26 2.708,0.99 false 6,1.854 4.813,1.188 false 2.802,0.885 3.052,1.073 0.25,0.188 10 false *a 2.781,2.042 3,2.24 0.219,0.198 10 false *1 3.198,0.125 3.396,0.365 0.198,0.24 10 false *b 4.583,1.052 4.854,1.26 0.271,0.208 10 false *a 4.635,1.688 4.875,1.875 0.24,0.188 10 false *1

Text in Illustration
*1 Oil Drain - -
*a Coked Oil *b Oil Drain Clogged with Coked Oil

HINT:

This illustration is not the turbocharger of the 1VD-FTV engine.


Turbine Shaft
Main fault
·

Breakage

·

Seizure


Symptoms
·

Shaft does not rotate

·

Oil leak to compressor housing

·

Large amount of white smoke from exhaust pipe

·

Lack of power

·

Turbocharger noise changes


Note
·

In case of turbine shaft failure, lack of power due to lack of boost pressure will be felt.

·

In cold conditions, shaft rotation can feel somewhat clingy due to viscosity of oil. Be sure not to mistake it for unsmooth shaft rotation.



Compressor Impeller
Main fault Breakage
Symptoms
·

Shaft does not rotate

·

Oil leak to compressor housing

·

Lack of power


Note
·

In case of compressor impeller failure, large amount of oil would be found between compressor outlet and intercooler, and between intercooler and intake manifold, but not found at compressor inlet.

·

Oil is blocked by boost pressure at compressor seal ring. Therefore, if boost pressure does not increase due to breakage of compressor impeller, oil flows out to compressor housing.



Compressor Housing FIPG Sealing Part
Symptoms Oil leak from FIPG sealing part
Note
·

If oil stain is separated from FIPG sealing part, it can be determined to be due to oil spray from other parts surrounding turbocharger.

·

If oil stain is traced to hose connection part, it can be determined to be due to hose connection failure.



A206069E01
4.516,0.272 4.721,0.472 0.205,0.2 10 *1 4.638,1.568 4.829,1.746 0.191,0.178 10 *2 4.548,2.126 4.753,2.326 0.205,0.2 10 *3 2.109,1.824 2.311,1.999 0.202,0.175 10 *a 2.275,2.347 2.484,2.508 0.209,0.161 10 *b 2.295,1.891 2.424,1.699 false 4.481,0.343 4.239,0.72 false 4.621,1.629 3.87,1.411 false 4.535,2.18 3.941,1.802 false

Text in Illustration
*1 Compressor Back Plate *2 FIPG Sealing Part
*3 Compressor Housing - -
*a Oil Leak *b Oil Leak from FIPG Sealing Part

HINT:

This illustration is not the turbocharger of the 1VD-FTV engine.


Intake Hoses
Symptoms Oil leak from hose connection between hose and compressor housing
Note If oil stain is traced to hose connection part, it can be determined to be due to hose connection failure.

A206070E01
0.123,0.0 0.344,0.172 0.221,0.172 10 *A 2.371,0.76 2.566,0.964 0.195,0.205 10 *a 2.355,2.348 2.587,2.538 0.232,0.19 10 *b 3.958,0.359 4.159,0.53 0.201,0.172 10 *1 4.589,2.109 4.781,2.311 0.192,0.202 10 *2 2.55,0.838 2.76,0.841 false 3.958,0.432 3.216,0.517 false 4.565,2.155 4.116,2.01 false

Text in Illustration
*A Fig. 5 - -
*1 Compressor Outlet *2 Compressor Housing
*a Trace of Oil Leak from Hose Connection Part *b Oil Leak from Hose Connection Part

HINT:

This illustration is not the turbocharger of the 1VD-FTV engine.



PROCEDURE

1.CHECK TYPE OF OIL LEAK
a.

Check whether the oil leak is an internal or external oil leak.

HINT:

White smoke is not related to an external oil leak.

Oil Leak Type Description
Internal oil leak
(White smoke)
Oil leak from bearing housing to compressor housing (intake side) or turbine housing (exhaust side) through seal rings.
Internal oil leak is not visible from outside of turbocharger.
If oil leak occurs from turbine side seal, large amount of white smoke will be emitted from exhaust pipe.
External oil leak Oil leak from inside of turbocharger to outside of turbocharger (e.g. from FIPG seal, oil pipe flange or oil pipe union).
Includes oil leaks visible from outside of turbocharger.


Result
Result Proceed to
External oil leak A
Internal oil leak B



A

2.REPLACE THE PART WHICH IS LEAKING OIL

B

3.CHECK WHITE SMOKE
2.REPLACE THE PART WHICH IS LEAKING OIL
a.

Replace the part which is leaking oil.



NEXT

END

3.CHECK WHITE SMOKE
a.

Fully depress the accelerator pedal, and then release it.


b.
A221583E04
0.291,0.017 0.940,0.228 0.649,0.211 10 *a

Check whether white smoke is emitted or not when racing the engine.

Text in Illustration
*a Example

CAUTION:

Be sure not to check for white smoke indoors.


Result
Result Proceed to
White smoke is emitted A
White smoke is not emitted B

HINT:
·

If white smoke appears for only a short period of time immediately after the engine is started, the white smoke is not from the turbocharger.

·

If the turbocharger is the cause of the problem, regardless of whether the engine is cold or warmed up, there will be a large amount of white smoke to the extent that visibility is obstructed for a few meters in the area of the smoke (as shown in the illustration).

·

Depending on whether there is oil mixed with the fuel, or whether there is unburned fuel present, the smell of the exhaust gas differs. When oil is mixed in, the exhaust gas smells like burning oil.





B

4.INSPECT COMPRESSOR INLET

A

4.INSPECT COMPRESSOR INLET
a.

Remove the engine assembly from the vehicle (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL).


b.

Remove the intake air connector pipe and inlet compressor elbow (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).


c.

Check whether an excessive amount of oil is present or not, and whether excessive oil deposits are attached to the compressor impeller or not.

HINT:
·

A certain amount of oil may be present as shown in fig. 2 in "Description", because a certain amount of oil mist is contained in the PCV gas and this oil accumulates just before the compressor inlet.

·

For 1KD-FTV engines, only bank 2 has a PCV path. Therefore, the oil shown in fig. 2 only exists for the turbocharger sub-assembly (for bank 2) and not for the turbocharger sub-assembly (for bank 1).

·

If an excessive amount of oil is present at the compressor inlet, there may be a problem in the PCV system.




d.

Reinstall the intake air connector pipe and inlet compressor elbow (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>INSTALLATION).



NEXT

5.INSPECT COMPRESSOR OUTLET
5.INSPECT COMPRESSOR OUTLET
a.

Check whether or not an excessive amount of oil or excessive oil deposits are present at the compressor outlet.

HINT:

A certain amount of oil may be present as shown in fig. 3 in "Description", because a certain amount of oil mist is contained in the PCV gas.


Result
Result Proceed to
Excessive amount of oil present at both compressor inlet and outlet A
Excessive amount of oil present only at compressor outlet B
Excessive amount of oil not present at compressor inlet or outlet C


b.

Reinstall the air tube assembly.



C

6.INSPECT TURBINE INLET

A

CHECK PCV SYSTEM

B

8.REPLACE TURBOCHARGER SUB-ASSEMBLY
6.INSPECT TURBINE INLET
a.

Remove the turbocharger sub-assembly (for bank 1 or bank 2) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).


b.

Check whether an excessive amount of wet oil or excessive oil deposits are present at the turbine inlet.

HINT:

Be sure not to mistake carbon soot for oil.




NEXT

7.INSPECT TURBINE OUTLET
7.INSPECT TURBINE OUTLET
a.

Check whether an excessive amount of wet oil or excessive oil deposits are present at the turbine outlet.

HINT:
·

Be sure not to mistake carbon soot for oil.

·

If the turbocharger shaft is tilted, some amount of oil will flow out from the bearing housing. Therefore, be sure not to mistake oil that flowed out from the bearing housing during or after the removal of the turbocharger for oil that was present before the removal of the turbocharger.

·

If an excessive amount of oil or excessive oil deposits are present at the turbine inlet, this oil is coming from the exhaust port of the cylinders, and may indicate a problem in 1 or more cylinders.



Result
Result Proceed to
Excessive amount of oil present at both turbine inlet and outlet A
Excessive amount of oil present only at turbine outlet B



B

8.REPLACE TURBOCHARGER SUB-ASSEMBLY

A

CHECK ENGINE TO DETERMINE CAUSE OF OIL IN TURBOCHARGER

8.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly (for bank 1 or bank 2) which is on the bank confirmed to be malfunctioning (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NEXT

END