Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  Pre-heating Control Circuit  


DESCRIPTION

The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates a time interval of the current that needs to flow through the glow plug depending on the starting engine coolant temperature when the engine switch is turned on (IG). The ECM then turns on the glow relay and permits current to flow through the glow plug based on the ECM calculated time. The glow plug is then heated, and enhances fuel combustion with a cold engine.

A DTC will be stored if the glow plug or the circuit is open.

A154593E07
0.552,1.104 1.063,1.479 0.51,0.375 10 false from Battery 0.167,0.115 2.031,0.323 1.865,0.208 10 false Glow System Wiring Diagram 1.531,0.927 2.063,1.094 0.531,0.167 10 false GLOW1 3.25,1.781 3.781,1.958 0.531,0.177 10 false GLOW1 5.229,1.198 5.708,1.375 0.479,0.177 10 false GREL 0.802,2.917 1.813,3.104 1.01,0.188 10 false No. 1 Glow Plug 5.833,2.635 6.24,2.802 0.406,0.167 10 false ECM

HINT:
·

These troubleshooting procedures are for: 1) difficult engine starting in cold weather, and 2) difficulty driving/vehicle malfunctions in cold weather immediately after engine is started.

·

After the engine is started, the ECM performs "after-glow" for a certain period of time. In proportion to the actual engine coolant temperature, the time period varies. The after-glow reduces diesel engine knocking, white smoke emissions and engine noises when the engine is cold.



A384648E01
0.125,0.094 1.354,0.323 1.229,0.229 10 false After-glow System 1.344,0.271 2.333,0.656 0.99,0.385 10 false After-glow Time (Second) 2.448,0.552 2.75,0.719 0.302,0.167 10 false 300 2.573,1.281 2.76,1.448 0.188,0.167 10 false 1 2.74,1.458 2.927,1.625 0.188,0.167 10 false 0 3.156,1.458 3.344,1.625 0.188,0.167 10 false 32 4.031,1.448 4.219,1.615 0.188,0.167 10 false 40 4.656,1.448 4.906,1.646 0.25,0.198 10 false °C 3.115,1.604 3.427,1.823 0.313,0.219 10 false (90) 3.958,1.583 4.344,1.802 0.385,0.219 10 false (104) 4.625,1.583 5.01,1.802 0.385,0.219 10 false (°F) 2.813,1.792 4.656,2.01 1.844,0.219 10 false Engine Coolant Temperature 4.385,2.021 4.885,2.229 0.5,0.208 10 false on (IG) 2.427,2.438 2.656,2.625 0.229,0.188 10 false off 2.406,3.219 2.771,3.406 0.365,0.188 10 false OFF 4.344,2.802 4.708,2.99 0.365,0.188 10 false ON 5.865,3.208 6.229,3.396 0.365,0.188 10 false OFF 1.219,2.51 2.167,2.719 0.948,0.208 10 false Engine Switch 1.448,3.333 2.198,3.552 0.75,0.219 10 false Glow Plug 1.229,4.094 2.177,4.302 0.948,0.208 10 false Engine Speed 2.865,4.469 3.813,4.677 0.948,0.208 10 false Engine Starts 4.219,4.385 5.25,4.573 1.031,0.188 10 false After-glow Time

WIRING DIAGRAM

A182513E06
0.813,6.833 1.302,7.021 0.49,0.188 10 false Battery 1.823,6.833 2.313,7.021 0.49,0.188 10 false Battery 0.26,4.781 0.385,4.927 0.125,0.146 10 false 1 0.479,4.802 0.708,4.948 0.229,0.146 10 false 1J 1.51,4.281 1.792,4.458 0.281,0.177 10 false 1N 1.51,0.865 1.813,1.063 0.302,0.198 10 false 1M 1.552,4.094 1.677,4.24 0.125,0.146 10 false 1 1.573,0.646 1.698,0.792 0.125,0.146 10 false 1 3.938,1.24 4.063,1.385 0.125,0.146 10 false 1 4.469,1.24 4.594,1.385 0.125,0.146 10 false 1 3.917,2.542 4.073,2.719 0.156,0.177 10 false 1 4.469,2.531 4.594,2.677 0.125,0.146 10 false 1 3.938,4.583 4.063,4.729 0.125,0.146 10 false 1 4.469,4.583 4.594,4.729 0.125,0.146 10 false 1 3.938,5.865 4.063,6.01 0.125,0.146 10 false 1 4.469,5.865 4.594,6.01 0.125,0.146 10 false 1 0.74,4.417 1.365,4.583 0.625,0.167 10 false GLOW 2 0.74,1.031 1.365,1.198 0.625,0.167 10 false GLOW 1 1.854,1.146 2.844,1.542 0.99,0.396 10 false Engine Room Relay Block 4.802,2.771 5.792,3.167 0.99,0.396 10 false Engine Room Relay Block 4.802,6.073 5.792,6.469 0.99,0.396 10 false Engine Room Relay Block 2.292,3.094 2.615,3.25 0.323,0.156 10 false C77 2.281,3.26 3.031,3.625 0.75,0.365 10 false No. 1 Glow Plug 2.281,6.354 2.594,6.521 0.313,0.167 10 false C78 2.292,6.521 3.031,6.875 0.74,0.354 10 false No. 2 Glow Plug 4.771,1.823 5.354,2.01 0.583,0.188 10 false GLOW 1 4.771,5.188 5.49,5.375 0.719,0.188 10 false GLOW 2 3.844,1.49 3.979,1.635 0.135,0.146 10 false 5 4.552,1.49 4.688,1.635 0.135,0.146 10 false 2 3.844,2.281 3.979,2.427 0.135,0.146 10 false 3 4.552,2.281 4.688,2.427 0.135,0.146 10 false 1 3.854,2.927 3.99,3.073 0.135,0.146 10 false 1 3.844,4.823 3.979,4.969 0.135,0.146 10 false 5 4.552,4.823 4.688,4.969 0.135,0.146 10 false 2 3.844,5.583 3.979,5.729 0.135,0.146 10 false 3 4.552,5.583 4.688,5.729 0.135,0.146 10 false 1 6.146,0.833 6.563,1.01 0.417,0.177 10 false GREL 5.833,0.979 6.052,1.177 0.219,0.198 10 false 12 6.146,4.26 6.563,4.438 0.417,0.177 10 false GRL2 5.833,4.375 6.021,4.552 0.188,0.177 10 false 23 5.979,6.896 6.938,7.073 0.958,0.177 10 false A38*1, A52*2 5.979,7.073 6.354,7.25 0.375,0.177 10 false ECM 4.656,6.792 5.448,6.969 0.792,0.177 10 false *1: for LHD 4.656,7.094 5.448,7.271 0.792,0.177 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ECM TERMINAL VOLTAGE (GREL TERMINAL)
a.
A182516E01
0.146,0.034 2.552,0.443 2.406,0.409 10 Front view of wire harness connector: (to Engine Room Relay Block) 0.57,4.113 1.181,4.276 0.611,0.163 10 GLOW 1 1.627,4.113 2.242,4.276 0.614,0.163 10 GLOW 2

Remove the GLOW 1 relay from the engine room relay block.


b.

Remove the GLOW 2 relay from the engine room relay block.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GLOW 1 relay (2) - Body ground Engine switch on (IG) 11 to 14 V
GLOW 2 relay (2) - Body ground Engine switch on (IG) 11 to 14 V




OK

2.INSPECT GLOW RELAY (GLOW 1 or 2)

NG

7.CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - ECM AND BODY GROUND)
2.INSPECT GLOW RELAY (GLOW 1 or 2)

OK

3.INSPECT FUSE (GLOW 1 and GLOW 2)

NG

REPLACE GLOW RELAY (GLOW 1 or 2)

3.INSPECT FUSE (GLOW 1 and GLOW 2)
A182514E01
0.126,0.01 2.025,0.200 1.899,0.191 10 Engine Room Relay Block: 0.332,2.895 0.884,3.079 0.551,0.184 10 GLOW1 1.252,2.895 1.801,3.079 0.549,0.184 10 GLOW2 0.876,2.043 0.662,2.861 false 0.977,2.048 1.493,2.851 false

a.

Remove the GLOW 1 and GLOW 2 fuses from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Component Condition Specified Condition
GLOW 1 H-fuse Always Below 1 Ω
GLOW 2 H-fuse Always Below 1 Ω




OK

4.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE

4.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

OK

5.CHECK GLOW PLUG ASSEMBLY (INSTALLATION)

NG

5.CHECK GLOW PLUG ASSEMBLY (INSTALLATION)
a.

Check the glow plug installation (See page Engine / Hybrid System>1VD-FTV (STARTING)>GLOW PLUG>INSTALLATION).

OK:

Glow plugs are installed securely.




OK

6.CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - GLOW PLUG - BATTERY AND BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - GLOW PLUG - BATTERY AND BODY GROUND)
a.

Remove the GLOW 1 relay from the engine room relay block.

A384649E01
4.75,1.5 5.135,1.75 0.385,0.25 5.531,1.5 5.917,1.75 0.385,0.25 0.115,0.063 2.406,0.708 2.292,0.646 10 true Front view of wire harness connector: (to Engine Room Relay Block) 4.208,0.083 6.5,0.458 2.292,0.375 10 false Front view of wire harness connector: (to Glow Plug Connector) 4.802,1.542 5.156,1.719 0.354,0.177 10 false C77 5.594,1.552 5.948,1.729 0.354,0.177 10 false C78 5.198,1.521 5.552,1.698 0.354,0.177 10 false *1 5.958,1.531 6.313,1.708 0.354,0.177 10 false *2 4.365,2.854 5.073,3.042 0.708,0.188 10 false *1: No. 1 4.354,3.208 5.063,3.396 0.708,0.188 10 false *2: No. 2 1.531,3.229 2.24,3.417 0.708,0.188 10 false GLOW 1 2.438,3.229 3.063,3.406 0.625,0.177 10 false GLOW 2


b.

Disconnect the C77 glow plug connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 1
Tester Connection Condition Specified Condition
GLOW 1 relay (3) - C77-1 Always Below 1 Ω
GLOW 1 relay (5) - Positive (+) battery terminal cable Always Below 1 Ω
GLOW 1 relay (1) - Body ground Always Below 1 Ω



d.

Remove the GLOW 2 relay from the engine room relay block.


e.

Disconnect the C78 glow plug connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 2
Tester Connection Condition Specified Condition
GLOW 2 relay (3) - C78-1 Always Below 1 Ω
GLOW 2 relay (5) - Positive (+) battery terminal cable Always Below 1 Ω
GLOW 2 relay (1) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - ECM AND BODY GROUND)
a.

Remove the GLOW 1 relay from the engine room relay block.

U163708E02
4.958,2.531 5.458,1.865 false 5.469,1.802 5.813,2.542 false 0.563,3.344 2.875,3.698 2.313,0.354 10 false Front view of wire harness connector: (to Engine Room Relay Block) 4.25,0.531 6.573,0.896 2.323,0.365 10 false Front view of wire harness connector: (to ECM) 4.417,2.99 5.354,3.167 0.938,0.177 10 false *1: for LHD 4.417,3.281 5.313,3.458 0.896,0.177 10 false *2: for RHD 5,1.26 5.323,1.427 0.323,0.167 10 false A38 5.302,1.083 5.51,1.25 0.208,0.167 10 false *1 0.823,2.979 1.427,3.146 0.604,0.167 10 false GLOW 1 1.75,2.979 2.354,3.146 0.604,0.167 10 false GLOW 2 4.865,2.563 5.615,2.781 0.75,0.219 10 false 23 (GRL2) 5.719,2.552 6.51,2.719 0.792,0.167 10 false 12 (GREL) 5.656,1.25 5.979,1.417 0.323,0.167 10 false A52 5.948,1.083 6.156,1.25 0.208,0.167 10 false *2


b.

Remove the GLOW 2 relay from the engine room relay block.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
GLOW 1 relay (2) - A38-12 (GREL) Always Below 1 Ω
GLOW 2 relay (2) - A38-23 (GRL2) Always Below 1 Ω
GLOW 1 relay (2) or A38-12 (GREL) - Body ground Always 10 kΩ or higher
GLOW 2 relay (2) or A38-23 (GRL2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
GLOW 1 relay (2) - A52-12 (GREL) Always Below 1 Ω
GLOW 2 relay (2) - A52-23 (GRL2) Always Below 1 Ω
GLOW 1 relay (2) or A52-12 (GREL) - Body ground Always 10 kΩ or higher
GLOW 2 relay (2) or A52-23 (GRL2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR