The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail system is controlled.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Crank or start engine | When the following condition is met (for 5 seconds during cranking or 0.5 seconds during engine start) (1 trip detection logic):
·
No crankshaft position sensor signal is sent to the ECM while cranking. |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
No. 1 crankshaft position sensor plate ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Engine running at 1000 rpm or more with vehicle stationary | No crankshaft position sensor signal is input to the ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met (1 trip detection logic):
(a) Engine speed is 1000 rpm or more. (b) STA signal is off. (c) 3 seconds or more have elapsed after STA signal is switched from on to off. |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
No. 1 crankshaft position sensor plate ·
No. 2 camshaft timing sprocket ·
ECM |
| DTC No. | Data List |
|---|---|
| P0335
P0339 |
Engine Speed |
If DTC P0335 and/or P0339 is stored, the following symptoms may appear:
Difficulty starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
The Data List item Engine Speed is calculated from the output of the crankshaft position sensor.
A DTC is also stored when the ground of a shielded wire is faulty.
Inspect the crankshaft position sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSPECTION).
OK
NG
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-1 (NE+) - C45-78 (NE+) | Always | Below 1 Ω |
| C65-2 (NE-) - C45-77 (NE-) | Always | Below 1 Ω |
| C65-1 (NE+) or C45-78 (NE+) - Body ground | Always | 10 kΩ or higher |
| C65-2 (NE-) or C45-77 (NE-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-1 (NE+) - C46-78 (NE+) | Always | Below 1 Ω |
| C65-2 (NE-) - C46-77 (NE-) | Always | Below 1 Ω |
| C65-1 (NE+) or C46-78 (NE+) - Body ground | Always | 10 kΩ or higher |
| C65-2 (NE-) or C46-77 (NE-) - Body ground | Always | 10 kΩ or higher |
Reconnect the crankshaft position sensor connector.
Reconnect the ECM connector.
OK
NG
Check the sensor installation.
Sensor is installed correctly.
OK
NG
Check the teeth of the sensor plate.
The sensor plate teeth do not have any cracks or deformation.
OK
NG
Check the condition of the timing sprocket.
Timing sprocket does not have any cracks or deformation.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Replace the crankshaft position sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Securely reinstall the sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSTALLATION).
NEXT
Replace the No. 1 crankshaft position sensor plate (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).
NEXT
Replace the No. 2 camshaft timing sprocket (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine and run it at 1000 rpm or more for 5 seconds or more.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT