Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0201  Injector Circuit / Open - (Cylinder 1)  P0202  Injector Circuit / Open - (Cylinder 2)  P0203  Injector Circuit / Open - (Cylinder 3)  P0204  Injector Circuit / Open - (Cylinder 4)  P0205  Injector Circuit / Open - (Cylinder 5)  P0206  Injector Circuit / Open - (Cylinder 6)  P0207  Injector Circuit / Open - (Cylinder 7)  P0208  Injector Circuit / Open - (Cylinder 8)  P062D  No. 1 Fuel Injector Driver Circuit Performance  P062E  No. 2 Fuel Injector Driver Circuit Performance  


DESCRIPTION

The injector driver (EDU) delivers drive signals to fuel injectors using the DC/DC converter, which provides a high-voltage and quick-charging system.

Soon after the injector driver (EDU) receives a fuel injection command (# 1 to # 8) signal from the ECM, the injector driver (EDU) responds to the command with an injector injection confirmation (INJF, INF2) signal when the current is applied to the injector assembly.

U163705E01
3.792,5.297 5.267,5.468 1.475,0.171 10 Injector Driver (EDU) 2.567,1.365 3.235,1.759 0.669,0.394 10 DC/DC Converter 0.066,1.336 1.428,1.511 1.362,0.174 10 from EDU 1 Relay 0.316,2.109 1.407,2.288 1.091,0.179 10 Command Pulse 0.253,4.904 1.468,5.084 1.215,0.179 10 Confirmation Pulse 0.131,5.202 1.249,5.727 1.119,0.526 10 Injector Driver (EDU) Connector 0.063,0.036 3.687,0.215 3.624,0.179 10 No. 1 Injector Driver (EDU) Wiring Diagram: 0.664,3.526 0.995,3.691 0.332,0.165 10 ECM 1.556,2.376 1.823,2.541 0.267,0.165 10 #1 1.556,2.689 1.823,2.854 0.267,0.165 10 #4 1.556,2.997 1.823,3.163 0.267,0.165 10 #6 1.556,3.301 1.823,3.466 0.267,0.165 10 #7 1.478,3.911 1.885,4.076 0.407,0.165 10 INJF 1.478,4.53 1.827,4.695 0.349,0.165 10 IJEN 1.478,3.605 1.805,3.770 0.327,0.165 10 PRD 1.478,4.209 1.805,4.374 0.327,0.165 10 RLF 5.007,2.357 5.357,2.526 0.350,0.169 10 IJ1- 5.007,0.472 5.433,0.642 0.427,0.169 10 RLF+ 5.007,0.796 5.406,0.965 0.399,0.169 10 IJ7+ 5.007,1.112 5.406,1.282 0.399,0.169 10 IJ6+ 5.007,1.431 5.406,1.601 0.399,0.169 10 IJ4+ 5.007,1.754 5.406,1.923 0.399,0.169 10 IJ1+ 5.007,2.69 5.357,2.860 0.350,0.169 10 IJ4- 5.007,2.999 5.357,3.169 0.350,0.169 10 IJ6- 5.007,3.32 5.357,3.490 0.350,0.169 10 IJ7- 5.007,3.641 5.388,3.810 0.382,0.170 10 RLF- 3.232,3.147 3.697,3.480 0.465,0.333 10 Control Circuit 3.012,5.295 3.358,5.465 0.346,0.170 10 GND 1.276,7.405 6.164,7.579 4.889,0.174 10 CAUTION: Terminals L, M, N, O, P, Q, R and S are high voltage terminals. 0.788,6.198 1.192,6.407 0.404,0.209 10 C153 2.457,5.976 2.851,6.126 0.393,0.150 10 C152 3.794,5.98 4.179,6.150 0.385,0.170 10 C151 5.113,5.98 5.495,6.163 0.383,0.184 10 C150 5.967,2.332 6.130,2.502 0.164,0.169 10 *1 6.191,2.332 6.354,2.502 0.164,0.169 10 *1 6.401,2.332 6.564,2.502 0.164,0.169 10 *1 6.611,2.332 6.775,2.502 0.164,0.169 10 *1 6.903,2.131 7.067,2.300 0.164,0.169 10 *2 5.193,4.661 6.563,4.996 1.370,0.335 10 *1: Injector Assembly 5.193,4.997 7.045,5.333 1.852,0.335 10 *2: Pressure Discharge Valve

P0201 to P0208:
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 5 seconds Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in injector assembly circuit

·

Injector assembly

·

No. 1 Injector driver (EDU)

·

No. 2 Injector driver (EDU)

·

ECM



P062D (No. 1), P062E (No. 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 5 seconds Inconsistency in the injection waveforms between the injector driver (EDU) and ECM while the engine is running a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
·

Open or short in injector driver (EDU) circuit

·

Injector assembly

·

No. 1 injector driver (EDU)

·

No. 2 injector driver (EDU)

·

ECM



MONITOR DESCRIPTION

P0201 to P0208:

The ECM compares injection command (# 1 to # 8) signals and injection confirmation (INJF, INF2) signals for each cylinder. If the ECM determines that a cylinder has a malfunction, DTC P0201, P0202, P0203, P0204, P0205, P0206, P0207 or P0208 will be stored.


P062D, P062E:

The ECM continuously monitors both injection command (#1 to #8) signals and injection confirmation (INJF, INF2) signals. These DTCs DTC will be stored if the ECM determines that the number of #1 to #8 signals and INJF, INF2 signals are inconsistent.

The injector assemblies are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the injector driver (EDU) (injector drive circuit) in relation to the current drawn by the injector assembly. When the injector assembly current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF or INF2 signal for that cylinder is sent to the ECM.

After the engine is started, when there is no injection confirmation (INJF, INF2) signal from the injector driver (EDU) to the ECM even though the ECM sends injection command (#1 to #8) signals to the injector driver (EDU), DTC P062D or P062E is stored.

If either of these DTCs is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the ignition switch is turned off.

A145849E52
4.958,2.5 4.625,2.854 false 4.656,3.25 4.865,3.583 false 0.115,0.083 1.698,0.292 1.583,0.208 10 false Malfunction Detection: 2.604,0.656 3.01,0.854 0.406,0.198 10 false ECM 0.063,1.76 1.75,1.979 1.688,0.219 10 false Injection Command Signal 0.063,3.083 2.01,3.292 1.948,0.208 10 false Injection Confirmation Signal 1.833,2.021 2.438,2.229 0.604,0.208 10 false #1 to #8 1.667,2.771 2.458,2.979 0.792,0.208 10 false INJF, INF2 3.302,1.781 3.583,1.979 0.281,0.198 10 false ON 3.615,0.479 5.406,0.719 1.792,0.24 10 false Command Signal (#1 to #8) 3.458,1.146 5.552,1.344 2.094,0.198 10 false Confirmation Signal (INJF, INF2) 5.896,0.656 6.281,0.854 0.385,0.198 10 false EDU 3.708,2.146 4.073,2.344 0.365,0.198 10 false OFF 5.01,2.375 5.781,2.573 0.771,0.198 10 false Abnormal 4.917,3.49 5.5,3.688 0.583,0.198 10 false Normal


WIRING DIAGRAM

A275254E03
0.113,0.059 0.539,0.242 0.427,0.184 10 No. 1: 0.616,0.789 0.957,0.959 0.341,0.170 10 INJF 1.021,0.789 1.447,0.948 0.427,0.159 10 C152 1.021,1.228 1.447,1.387 0.427,0.159 10 C152 1.021,1.669 1.447,1.829 0.427,0.159 10 C152 1.021,2.101 1.447,2.261 0.427,0.159 10 C152 1.021,2.545 1.447,2.704 0.427,0.159 10 C152 1.021,3.042 1.447,3.202 0.427,0.159 10 C151 1.021,3.974 1.447,4.133 0.427,0.159 10 C151 1.021,5.307 1.406,5.467 0.385,0.159 10 C151 1.021,5.877 1.406,6.037 0.385,0.159 10 C151 1.021,6.804 1.406,6.964 0.385,0.159 10 C151 1.021,8.149 1.383,8.309 0.362,0.159 10 C150 1.107,0.619 1.225,0.778 0.117,0.159 10 1 0.664,1.226 0.957,1.395 0.293,0.170 10 #10 1.107,1.056 1.225,1.215 0.117,0.159 10 5 0.664,1.67 0.957,1.840 0.293,0.170 10 #40 1.107,1.5 1.225,1.660 0.117,0.159 10 6 0.664,2.104 0.957,2.273 0.293,0.170 10 #60 1.107,1.933 1.225,2.093 0.117,0.159 10 2 0.664,2.547 0.957,2.717 0.293,0.170 10 #70 6.206,0.789 6.547,0.959 0.341,0.170 10 INJ1 6.206,1.226 6.499,1.395 0.293,0.170 10 #1 6.206,1.674 6.499,1.844 0.293,0.170 10 #4 6.206,2.104 6.499,2.273 0.293,0.170 10 #6 6.206,2.553 6.499,2.723 0.293,0.170 10 #7 5.858,0.789 6.140,0.948 0.282,0.159 10 C46 5.518,0.789 5.800,0.948 0.282,0.159 10 C45 5.826,0.617 6.174,0.776 0.348,0.159 10 60*2 5.493,0.617 5.820,0.776 0.327,0.159 10 60*1 5.858,1.23 6.140,1.390 0.282,0.159 10 C46 5.518,1.23 5.800,1.390 0.282,0.159 10 C45 5.826,1.058 6.174,1.218 0.348,0.159 10 40*2 5.493,1.058 5.820,1.218 0.327,0.159 10 40*1 5.858,1.672 6.140,1.831 0.282,0.159 10 C46 5.518,1.672 5.800,1.831 0.282,0.159 10 C45 5.826,1.5 6.174,1.659 0.348,0.159 10 37*2 5.493,1.5 5.820,1.659 0.327,0.159 10 37*1 5.858,2.106 6.140,2.265 0.282,0.159 10 C46 5.518,2.106 5.800,2.265 0.282,0.159 10 C45 5.826,1.934 6.174,2.093 0.348,0.159 10 35*2 5.493,1.934 5.820,2.093 0.327,0.159 10 35*1 5.858,2.551 6.140,2.710 0.282,0.159 10 C46 5.518,2.551 5.800,2.710 0.282,0.159 10 C45 5.826,2.379 6.174,2.538 0.348,0.159 10 34*2 5.493,2.379 5.820,2.538 0.327,0.159 10 34*1 1.107,2.377 1.225,2.536 0.117,0.159 10 3 0.636,3.042 0.957,3.212 0.321,0.170 10 IJ1+ 1.107,2.873 1.225,3.033 0.117,0.159 10 6 4.294,3.152 4.411,3.311 0.117,0.159 10 2 3.607,3.152 3.724,3.311 0.117,0.159 10 1 2.264,2.804 2.459,2.972 0.195,0.169 10 *3 2.264,4.207 2.459,4.375 0.195,0.169 10 *3 2.264,5.664 2.459,5.832 0.195,0.169 10 *3 2.264,6.999 2.459,7.167 0.195,0.169 10 *3 0.636,5.307 0.957,5.477 0.321,0.170 10 IJ4- 1.107,5.149 1.225,5.309 0.117,0.159 10 2 0.636,5.877 0.957,6.047 0.321,0.170 10 IJ6+ 1.107,5.72 1.225,5.880 0.117,0.159 10 4 0.636,8.149 0.957,8.319 0.321,0.170 10 IJ7- 1.107,7.982 1.225,8.141 0.117,0.159 10 2 0.678,3.974 0.962,4.144 0.284,0.170 10 IJ1- 1.107,3.811 1.225,3.970 0.117,0.159 10 3 0.664,6.804 0.966,6.974 0.303,0.170 10 IJ6- 1.107,6.643 1.225,6.802 0.117,0.159 10 1 3.423,3.354 3.824,3.531 0.401,0.177 10 C141 3.423,3.501 4.632,3.663 1.209,0.162 10 No. 1 Fuel Injector 3.423,4.699 3.933,4.876 0.510,0.177 10 C147 3.423,4.846 4.632,5.008 1.209,0.162 10 No. 4 Fuel Injector 3.423,6.163 3.933,6.340 0.510,0.177 10 C146 3.423,6.31 4.632,6.472 1.209,0.162 10 No. 6 Fuel Injector 3.423,7.543 3.933,7.720 0.510,0.177 10 C144 3.423,7.69 4.632,7.852 1.209,0.162 10 No. 7 Fuel Injector 4.294,4.517 4.411,4.677 0.117,0.159 10 2 3.607,4.517 3.724,4.677 0.117,0.159 10 1 4.294,5.996 4.411,6.155 0.117,0.159 10 2 3.607,5.996 3.724,6.155 0.117,0.159 10 1 4.294,7.334 4.411,7.493 0.117,0.159 10 2 3.607,7.334 3.724,7.493 0.117,0.159 10 1 5.255,8.495 6.046,8.651 0.792,0.157 10 *3: Shielded 5.255,8.221 6.046,8.378 0.792,0.157 10 *2: for RHD 6.361,8.424 6.764,8.581 0.403,0.157 10 ECM 5.255,7.948 6.046,8.105 0.792,0.157 10 *1: for LHD 0.664,4.392 0.985,4.562 0.321,0.170 10 IJ4+ 0.654,7.257 0.976,7.427 0.321,0.170 10 IJ7+ 1.007,4.387 1.433,4.547 0.427,0.159 10 C151 1.025,7.215 1.387,7.374 0.362,0.159 10 C150 1.123,4.205 1.240,4.365 0.117,0.159 10 5 1.152,7.043 1.270,7.203 0.117,0.159 10 4 0.134,8.523 1.884,8.679 1.750,0.157 10 No. 1 Injector Driver (EDU)

A375365E03
0.542,0.385 0.792,0.583 0.25,0.198 10 false +B 0.844,0.406 1.271,0.583 0.427,0.177 10 false C150 0.938,0.208 1.167,0.385 0.229,0.177 10 false 3 0.448,0.813 0.802,0.99 0.354,0.177 10 false GND 0.938,0.646 1.167,0.823 0.229,0.177 10 false 1 0.094,4.323 1.802,4.51 1.708,0.188 10 false No. 1 Injector Driver (EDU) 1.198,3.438 1.76,3.635 0.563,0.198 10 false Battery 1.198,2.229 1.563,2.396 0.365,0.167 10 false P/I-B 2.271,2.219 3.354,2.427 1.083,0.208 10 false EFI MAIN NO.1 3.042,3.135 4.167,3.344 1.125,0.208 10 false Integration Relay 4.833,2.135 5.635,2.313 0.802,0.177 10 false EDU NO.1 1.635,1.344 2.438,1.521 0.802,0.177 10 false EDU NO.1 5.823,0.813 6.125,1 0.302,0.188 10 false A38 6.51,0.802 6.906,0.958 0.396,0.156 10 false BATT 4.75,1.083 4.875,1.24 0.125,0.156 10 false 3 5.458,1.083 5.583,1.24 0.125,0.156 10 false 5 4.719,1.708 4.844,1.865 0.125,0.156 10 false 1 5.479,1.708 5.604,1.865 0.125,0.156 10 false 2 5.792,0.625 6.135,0.781 0.344,0.156 10 false 20*1 5.813,1.813 6.115,2 0.302,0.188 10 false A38 6.51,1.792 6.885,1.948 0.375,0.156 10 false IREL 5.792,1.625 6.146,1.781 0.354,0.156 10 false 45*1 5.823,3.229 6.115,3.396 0.292,0.167 10 false A38 6.49,3.24 6.938,3.396 0.448,0.156 10 false MREL 6.573,4.354 6.979,4.563 0.406,0.208 10 false ECM 5.792,3.052 6.146,3.208 0.354,0.156 10 false 44*1 5.083,3.958 5.854,4.146 0.771,0.188 10 false *1: for LHD 5.083,4.271 5.854,4.458 0.771,0.188 10 false *2: for RHD 5.823,2.406 6.146,2.583 0.323,0.177 10 false A38 6.51,2.385 6.771,2.542 0.26,0.156 10 false +B 5.844,2.219 6.083,2.375 0.24,0.156 10 false 2*1 6.156,0.823 6.469,1 0.313,0.177 10 false A52 6.125,0.625 6.469,0.813 0.344,0.188 10 false 20*2 6.156,1.813 6.479,1.99 0.323,0.177 10 false A52 6.135,1.625 6.49,1.781 0.354,0.156 10 false 45*2 6.167,3.24 6.479,3.417 0.313,0.177 10 false A52 6.135,3.052 6.49,3.208 0.354,0.156 10 false 44*2 6.167,2.406 6.458,2.594 0.292,0.188 10 false A52 6.188,2.219 6.427,2.375 0.24,0.156 10 false 2*2 2.688,1.75 2.813,1.906 0.125,0.156 10 false 7 2,1.896 2.26,2.052 0.26,0.156 10 false 1*2 2.906,1.75 3.146,1.938 0.24,0.188 10 false 1S 2.25,2.906 2.375,3.063 0.125,0.156 10 false 4 2.427,2.927 2.698,3.115 0.271,0.188 10 false 1S 2.01,2.094 2.24,2.271 0.229,0.177 10 false 1X 1.667,1.896 1.917,2.052 0.25,0.156 10 false 1*1 1.677,2.094 1.896,2.25 0.219,0.156 10 false 1Y 4.042,1.896 4.26,2.052 0.219,0.156 10 false 11 4.021,2.083 4.26,2.26 0.24,0.177 10 false 1S 4.083,2.292 4.208,2.448 0.125,0.156 10 false 8 4.031,2.479 4.281,2.677 0.25,0.198 10 false 1S 5.813,2.813 6.115,2.99 0.302,0.177 10 false A38 6.5,2.802 6.865,2.958 0.365,0.156 10 false +B2 5.833,2.635 6.073,2.792 0.24,0.156 10 false 1*1 6.146,2.823 6.427,2.979 0.281,0.156 10 false A52 6.177,2.635 6.417,2.792 0.24,0.156 10 false 1*2 0.844,0.823 1.271,1 0.427,0.177 10 false C150 3.042,2.792 4.135,2.979 1.094,0.188 10 false EFI MAIN NO.1

A275254E04
0.113,0.056 0.539,0.240 0.427,0.184 10 No. 2: 0.616,0.786 0.957,0.956 0.341,0.170 10 INF2 1.021,0.786 1.415,0.946 0.394,0.159 10 C156 1.021,1.225 1.415,1.385 0.394,0.159 10 C156 1.021,1.667 1.415,1.826 0.394,0.159 10 C156 1.021,2.099 1.415,2.258 0.394,0.159 10 C156 1.021,2.542 1.415,2.702 0.394,0.159 10 C156 1.026,3.04 1.489,3.199 0.463,0.159 10 C155 1.026,3.971 1.489,4.131 0.463,0.159 10 C155 1.026,5.305 1.380,5.464 0.354,0.159 10 C155 1.026,5.874 1.380,6.034 0.354,0.159 10 C154 1.026,6.801 1.380,6.961 0.354,0.159 10 C154 1.026,8.146 1.380,8.306 0.354,0.159 10 C155 0.15,8.539 1.933,8.698 1.782,0.159 10 No. 2 Injector Driver (EDU) 1.107,0.616 1.225,0.775 0.117,0.159 10 1 0.664,1.223 0.957,1.393 0.293,0.170 10 #20 1.107,1.053 1.225,1.212 0.117,0.159 10 5 0.664,1.668 0.957,1.837 0.293,0.170 10 #30 1.107,1.497 1.225,1.657 0.117,0.159 10 3 0.664,2.101 0.957,2.271 0.293,0.170 10 #50 1.107,1.931 1.225,2.090 0.117,0.159 10 6 0.664,2.544 0.957,2.714 0.293,0.170 10 #80 6.206,0.786 6.547,0.956 0.341,0.170 10 INJ2 6.206,1.223 6.499,1.393 0.293,0.170 10 #2 6.206,1.672 6.499,1.841 0.293,0.170 10 #3 6.206,2.101 6.499,2.271 0.293,0.170 10 #5 6.206,2.55 6.499,2.720 0.293,0.170 10 #8 5.858,0.786 6.140,0.946 0.282,0.159 10 C46 5.518,0.786 5.800,0.946 0.282,0.159 10 C45 5.826,0.614 6.174,0.774 0.348,0.159 10 61*2 5.493,0.614 5.820,0.774 0.327,0.159 10 61*1 5.858,1.228 6.140,1.387 0.282,0.159 10 C46 5.518,1.228 5.800,1.387 0.282,0.159 10 C45 5.826,1.056 6.174,1.215 0.348,0.159 10 39*2 5.493,1.056 5.820,1.215 0.327,0.159 10 39*1 5.858,1.669 6.140,1.828 0.282,0.159 10 C46 5.518,1.669 5.800,1.828 0.282,0.159 10 C45 5.826,1.497 6.174,1.656 0.348,0.159 10 38*2 5.493,1.497 5.820,1.656 0.327,0.159 10 38*1 5.858,2.103 6.140,2.263 0.282,0.159 10 C46 5.518,2.103 5.800,2.263 0.282,0.159 10 C45 5.826,1.931 6.174,2.091 0.348,0.159 10 36*2 5.493,1.931 5.820,2.091 0.327,0.159 10 36*1 5.858,2.548 6.140,2.707 0.282,0.159 10 C46 5.518,2.548 5.800,2.707 0.282,0.159 10 C45 5.826,2.376 6.174,2.535 0.348,0.159 10 33*2 5.493,2.376 5.820,2.535 0.327,0.159 10 33*1 1.107,2.374 1.225,2.533 0.117,0.159 10 2 0.649,3.04 0.970,3.209 0.321,0.170 10 IJ2+ 1.107,2.871 1.225,3.030 0.117,0.159 10 6 4.28,3.149 4.397,3.308 0.117,0.159 10 2 3.579,3.149 3.696,3.308 0.117,0.159 10 1 2.264,2.801 2.459,2.970 0.195,0.169 10 *3 2.264,4.204 2.459,4.373 0.195,0.169 10 *3 2.264,5.661 2.459,5.830 0.195,0.169 10 *3 2.264,6.996 2.459,7.165 0.195,0.169 10 *3 0.649,5.305 0.970,5.474 0.321,0.170 10 IJ5- 1.107,5.147 1.225,5.306 0.117,0.159 10 2 0.649,5.874 0.970,6.044 0.321,0.170 10 IJ3+ 1.107,5.718 1.225,5.877 0.117,0.159 10 4 0.649,8.146 0.952,8.316 0.303,0.170 10 IJ8- 1.107,7.979 1.225,8.139 0.117,0.159 10 1 1.107,3.808 1.225,3.967 0.117,0.159 10 3 0.649,6.801 0.915,6.971 0.266,0.170 10 IJ3- 1.107,6.64 1.225,6.799 0.117,0.159 10 2 3.423,3.351 3.809,3.528 0.385,0.177 10 C148 3.423,3.498 4.632,3.660 1.209,0.162 10 No. 2 Fuel Injector 3.423,4.696 3.905,4.873 0.482,0.177 10 C143 3.423,4.843 4.632,5.005 1.209,0.162 10 No. 5 Fuel Injector 3.423,6.161 3.836,6.337 0.412,0.177 10 C142 3.423,6.307 4.632,6.469 1.209,0.162 10 No. 3 Fuel Injector 3.423,7.541 3.850,7.717 0.426,0.177 10 C145 3.423,7.687 4.632,7.849 1.209,0.162 10 No. 8 Fuel Injector 4.28,4.515 4.397,4.674 0.117,0.159 10 2 3.579,4.515 3.696,4.674 0.117,0.159 10 1 4.28,5.993 4.397,6.152 0.117,0.159 10 2 3.579,5.993 3.696,6.152 0.117,0.159 10 1 4.28,7.331 4.397,7.490 0.117,0.159 10 2 3.579,7.331 3.696,7.490 0.117,0.159 10 1 5.255,8.492 6.046,8.648 0.792,0.157 10 *3: Shielded 6.375,8.436 6.757,8.592 0.382,0.157 10 ECM 5.255,8.219 6.046,8.375 0.792,0.157 10 *2: for RHD 5.255,7.945 6.046,8.102 0.792,0.157 10 *1: for LHD 1.025,4.388 1.488,4.547 0.463,0.159 10 C155 0.649,4.388 0.970,4.558 0.321,0.170 10 IJ5+ 1.107,4.219 1.224,4.378 0.117,0.159 10 5 0.992,7.219 1.455,7.379 0.463,0.159 10 C155 0.649,7.219 0.970,7.389 0.321,0.170 10 IJ8+ 1.079,7.05 1.196,7.210 0.117,0.159 10 4 0.649,3.991 0.970,4.161 0.321,0.170 10 IJ2-

A375366E01
0.833,0.406 1.26,0.583 0.427,0.177 10 false C154 0.833,0.833 1.26,1.01 0.427,0.177 10 false C154 0.5,0.385 0.792,0.563 0.292,0.177 10 false +B 0.406,0.823 0.781,1.01 0.375,0.188 10 false GND 1.656,1.365 2.396,1.552 0.74,0.188 10 false EDU NO.2 1.177,2.25 1.552,2.438 0.375,0.188 10 false P/I-B 1.677,2.094 1.906,2.26 0.229,0.167 10 false 1Y 1.99,2.094 2.219,2.26 0.229,0.167 10 false 1X 2.427,2.938 2.656,3.104 0.229,0.167 10 false 1P 4.021,2.49 4.25,2.656 0.229,0.167 10 false 1P 4.021,2.094 4.25,2.26 0.229,0.167 10 false 1P 1.219,3.427 1.958,3.615 0.74,0.188 10 false Battery 2.896,3.156 4.042,3.375 1.146,0.219 10 false Integration Relay 5.813,1.813 6.125,1.99 0.313,0.177 10 false A38 5.813,2.479 6.125,2.656 0.313,0.177 10 false A38 6.156,2.49 6.469,2.667 0.313,0.177 10 false A52 6.156,1.802 6.469,1.979 0.313,0.177 10 false A52 5.802,1.615 6.146,1.792 0.344,0.177 10 false 46*1 6.115,1.615 6.458,1.792 0.344,0.177 10 false 46*2 5.781,2.302 6.125,2.479 0.344,0.177 10 false 44*1 6.104,2.292 6.448,2.469 0.344,0.177 10 false 44*2 6.5,1.813 6.844,1.99 0.344,0.177 10 false IRL2 6.5,2.479 6.979,2.688 0.479,0.208 10 false MREL 6.563,4.375 7.042,4.583 0.479,0.208 10 false ECM 4.823,2.156 5.552,2.333 0.729,0.177 10 false EDU NO.2 1.656,1.896 1.99,2.073 0.333,0.177 10 false 1*1 1.979,1.896 2.313,2.073 0.333,0.177 10 false 1*2 2.26,2.229 3.281,2.438 1.021,0.208 10 false EFI MAIN NO.2 4.031,1.885 4.365,2.063 0.333,0.177 10 false 12 4.052,2.302 4.25,2.5 0.198,0.198 10 false 8 3.021,2.802 4.167,3.021 1.146,0.219 10 false EFI MAIN NO.2 2.135,2.917 2.375,3.094 0.24,0.177 10 false 11 0.115,4.323 1.938,4.521 1.823,0.198 10 false No. 2 Injector Driver (EDU) 4.854,3.927 5.656,4.125 0.802,0.198 10 false *1: for LHD 4.865,4.271 5.667,4.469 0.802,0.198 10 false *2: for RHD 4.708,1.688 4.896,1.875 0.188,0.188 10 false 1 4.719,1.094 4.906,1.281 0.188,0.188 10 false 3 5.458,1.094 5.646,1.281 0.188,0.188 10 false 5 5.448,1.708 5.635,1.896 0.188,0.188 10 false 2 0.938,0.188 1.125,0.375 0.188,0.188 10 false 3 0.958,0.635 1.146,0.823 0.188,0.188 10 false 1

CAUTION / NOTICE / HINT

CAUTION:

Make sure to perform work on high voltage circuits with the ignition switch off.


NOTICE:
·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ENGINE CRANKING CONDITION AND DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Read the DTCs.


e.

Check the engine cranking condition.

Result
Result Proceed to
Engine starts, but idling is rough (P062D or P062E is output)*1 A
Engine starts, but idling is rough*2 B
Engine does not start (P062D and P062E are output)*3 C
Except above D

HINT:
·

*1: Only one of either DTC P062D or P062E is output and one of the injector drivers (EDU) has stopped.

·

*2: DTC P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P062D and P062E are stored at this time.

·

*3: When the engine cannot be started due to a malfunction in the No. 1 and No. 2 injector driver (EDU), DTCs are not stored again if they are cleared. Also, the value for "Common Rail Pressure" is higher than the value for "Target Common Rail Pressure"





A

2.INSPECT ECM

B

6.CHECK WHETHER DTC OUTPUT RECURS

C

3.CHECK TERMINAL VOLTAGE (POWER SOURCE)

D

2.INSPECT ECM
a.
A384577E01
0.167,0.667 0.615,0.917 0.448,0.25 0.167,1.063 0.615,1.313 0.448,0.25 1.375,1.198 0.844,1.719 true 1.615,1.219 2.063,1.729 true 1.073,0.313 1.563,0.938 true 2.365,0.5 1.823,0.958 true 0.771,0.094 1.75,0.271 0.979,0.177 10 false #60*A, #80*B 2.448,0.406 3.344,0.583 0.896,0.177 10 false #70*A, #30*B 1.938,1.75 2.833,1.927 0.896,0.177 10 false #40*A, #50*B 0.729,1.76 1.625,1.938 0.896,0.177 10 false #10*A, #20*B 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.229,0.708 0.667,0.906 0.438,0.198 10 false C152 0.219,1.104 0.656,1.302 0.438,0.198 10 false C156 0.667,0.708 0.979,0.906 0.313,0.198 10 false *A 0.667,1.083 0.979,1.281 0.313,0.198 10 false *B 2.438,2.188 3.052,2.385 0.615,0.198 10 false 2 V/DIV. 3,3.344 3.365,3.542 0.365,0.198 10 false GND 0.354,4.177 1.323,4.385 0.969,0.208 10 false 1 msec./DIV.

Disconnect the No. 1 and No. 2 injector driver (EDU) connectors.


b.

Check the waveform of the No. 1 or No. 2 injector driver (EDU) connector using an oscilloscope.

OK:
Tester Connection Condition Specified Condition
C152-5 (#10) - Body ground Cranking Correct waveform is as shown
C156-5 (#20) - Body ground Cranking Correct waveform is as shown
C156-3 (#30) - Body ground Cranking Correct waveform is as shown
C152-6 (#40) - Body ground Cranking Correct waveform is as shown
C156-6 (#50) - Body ground Cranking Correct waveform is as shown
C152-2 (#60) - Body ground Cranking Correct waveform is as shown
C152-3 (#70) - Body ground Cranking Correct waveform is as shown
C156-2 (#80) - Body ground Cranking Correct waveform is as shown


Text in Illustration
*A for Bank 1 (No. 1 injector Driver (EDU))
*B for Bank 2 (No. 2 injector Driver (EDU))
*a Front view of wire harness connector
(to Injector Driver (EDU))



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE)

NG

11.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)
3.CHECK TERMINAL VOLTAGE (POWER SOURCE)
a.

Turn the ignition switch off.

HINT:

Powering of the EDU relay may be prohibited by the fail-safe function. Therefore, turn the ignition switch off to disable the failsafe function before performing this inspection.



b.
U163301E01
0.895,1.869 1.101,2.026 0.207,0.157 10 +B 0.943,0.18 1.277,0.331 0.334,0.151 10 GND 0.135,0.077 0.317,0.238 0.182,0.161 10 *a 0.198,0.779 0.572,0.942 0.373,0.163 10 C150 0.739,0.785 0.921,0.946 0.182,0.161 10 *A 0.21,1.421 0.583,1.583 0.373,0.163 10 C154 0.751,1.426 0.933,1.587 0.182,0.161 10 *B 1.553,0.895 1.169,0.369 false 1.514,1.454 1.089,1.86 false

Disconnect the No. 1 or No. 2 injector driver (EDU) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C150-3 (+B) - C150-1 (GND) Ignition switch ON 11 to 14 V
C154-3 (+B) - C154-1 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*A for Bank 1 (No. 1 injector Driver (EDU))
*B for Bank 2 (No. 2 injector Driver (EDU))
*a Front view of wire harness connector
(to Injector Driver (EDU))


e.

Reconnect the No. 1 or No. 2 injector driver (EDU) connector.



OK

4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)

NG

16.GO TO INJECTOR CIRCUIT
4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)
a.

Disconnect the No. 1 or No. 2 injector driver (EDU) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C152-5 (#10) - C45-40 (#1) Always Below 1 Ω
C156-5 (#20) - C45-39 (#2) Always Below 1 Ω
C156-3 (#30) - C45-38 (#3) Always Below 1 Ω
C152-6 (#40) - C45-37 (#4) Always Below 1 Ω
C156-6 (#50) - C45-36 (#5) Always Below 1 Ω
C152-2 (#60) - C45-35 (#6) Always Below 1 Ω
C152-3 (#70) - C45-34 (#7) Always Below 1 Ω
C156-2 (#80) - C45-33 (#8) Always Below 1 Ω
C152-1 (INJF) - C45-60 (INJ1) Always Below 1 Ω
C156-1 (INF2) - C45-61 (INJ2) Always Below 1 Ω
C152-5 (#10) or C45-40 (#1) - Body ground Always 10 kΩ or higher
C156-5 (#20) or C45-39 (#2) - Body ground Always 10 kΩ or higher
C156-3 (#30) or C45-38 (#3) - Body ground Always 10 kΩ or higher
C152-6 (#40) or C45-37 (#4) - Body ground Always 10 kΩ or higher
C156-6 (#50) or C45-36 (#5) - Body ground Always 10 kΩ or higher
C152-2 (#60) or C45-35 (#6) - Body ground Always 10 kΩ or higher
C152-3 (#70) or C45-34 (#7) - Body ground Always 10 kΩ or higher
C156-2 (#80) or C45-33 (#8) - Body ground Always 10 kΩ or higher
C152-1 (INJF) or C45-60 (INJ1) - Body ground Always 10 kΩ or higher
C156-1 (INF2) or C45-61 (INJ2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C152-5 (#10) - C46-40 (#1) Always Below 1 Ω
C156-5 (#20) - C46-39 (#2) Always Below 1 Ω
C156-3 (#30) - C46-38 (#3) Always Below 1 Ω
C152-6 (#40) - C46-37 (#4) Always Below 1 Ω
C156-6 (#50) - C46-36 (#5) Always Below 1 Ω
C152-2 (#60) - C46-35 (#6) Always Below 1 Ω
C152-3 (#70) - C46-34 (#7) Always Below 1 Ω
C156-2 (#80) - C46-33 (#8) Always Below 1 Ω
C152-1 (INJF) - C46-60 (INJ1) Always Below 1 Ω
C156-1 (INF2) - C46-61 (INJ2) Always Below 1 Ω
C152-5 (#10) or C46-40 (#1) - Body ground Always 10 kΩ or higher
C156-5 (#20) or C46-39 (#2) - Body ground Always 10 kΩ or higher
C156-3 (#30) or C46-38 (#3) - Body ground Always 10 kΩ or higher
C152-6 (#40) or C46-37 (#4) - Body ground Always 10 kΩ or higher
C156-6 (#50) or C46-36 (#5) - Body ground Always 10 kΩ or higher
C152-2 (#60) or C46-35 (#6) - Body ground Always 10 kΩ or higher
C152-3 (#70) or C46-34 (#7) - Body ground Always 10 kΩ or higher
C156-2 (#80) or C46-33 (#8) - Body ground Always 10 kΩ or higher
C152-1 (INJF) or C46-60 (INJ1) - Body ground Always 10 kΩ or higher
C156-1 (INF2) or C46-61 (INJ2) - Body ground Always 10 kΩ or higher



d.

Reconnect the No. 1 or No. 2 injector driver (EDU) connector.


e.

Reconnect the ECM connector.



OK

5.REPLACE INJECTOR DRIVER (EDU)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE INJECTOR DRIVER (EDU)
a.

Replace the No. 1 or No. 2 injector driver (EDU) (See page Engine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Turn the ignition switch off for 30 seconds.


e.

Start the engine and idle it for 30 seconds.


f.

Enter the following menus: Engine and ECT / Trouble Codes.


g.

Check the DTCs output on the GTS.

HINT:
·

The cylinder with the malfunctioning injector assembly can be determined based on the output DTCs.

·

If DTC P0201 is output, check the No. 1 injector assembly circuit.

·

If DTC P0202 is output, check the No. 2 injector assembly circuit.

·

If DTC P0203 is output, check the No. 3 injector assembly circuit.

·

If DTC P0204 is output, check the No. 4 injector assembly circuit.

·

If DTC P0205 is output, check the No. 5 injector assembly circuit.

·

If DTC P0206 is output, check the No. 6 injector assembly circuit.

·

If DTC P0207 is output, check the No. 7 injector assembly circuit.

·

If DTC P0208 is output, check the No. 8 injector assembly circuit.





NEXT

7.INSPECT INJECTOR DRIVER (EDU)
7.INSPECT INJECTOR DRIVER (EDU)
a.
A384578E01
0.167,0.458 0.615,0.708 0.448,0.25 0.167,0.76 0.615,1.01 0.448,0.25 0.167,1.063 0.615,1.313 0.448,0.25 0.167,1.354 0.615,1.604 0.448,0.25 0.667,0.458 1.115,0.708 0.448,0.25 0.667,0.76 1.115,1.01 0.448,0.25 0.667,1.063 1.115,1.313 0.448,0.25 0.667,1.354 1.115,1.604 0.448,0.25 2.25,2.125 3.01,2.333 0.76,0.208 10 false 100 V/DIV. 0.281,4.208 1.229,4.396 0.948,0.188 10 false 1 msec./DIV. 3.01,4.01 3.385,4.208 0.375,0.198 10 false GND 0.208,0.5 0.615,0.688 0.406,0.188 10 false C141 0.208,0.802 0.615,0.99 0.406,0.188 10 false C142 0.219,1.094 0.625,1.281 0.406,0.188 10 false C143 0.229,1.385 0.635,1.573 0.406,0.188 10 false C144 0.729,0.5 1.135,0.688 0.406,0.188 10 false C148 0.729,0.802 1.135,0.99 0.406,0.188 10 false C147 0.729,1.104 1.135,1.292 0.406,0.188 10 false C146 0.719,1.385 1.125,1.573 0.406,0.188 10 false C145

Disconnect the injector assembly connectors for all cylinders.

NOTICE:

If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.



b.

Check the waveform of the injector assembly connectors using an oscilloscope.

OK:
Tester Connection Condition Specified Condition
C141-1 - C141-2 Cranking Voltage increases by 50 V or more
C148-1 - C148-2 Cranking Voltage increases by 50 V or more
C142-1 - C142-2 Cranking Voltage increases by 50 V or more
C147-1 - C147-2 Cranking Voltage increases by 50 V or more
C143-1 - C143-2 Cranking Voltage increases by 50 V or more
C146-1 - C146-2 Cranking Voltage increases by 50 V or more
C144-1 - C144-2 Cranking Voltage increases by 50 V or more
C145-1 - C145-2 Cranking Voltage increases by 50 V or more


Text in Illustration
*a Front view of wire harness connector
(to Injector Assembly)



OK

8.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)

NG

13.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER (EDU))
8.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly of the cylinder relevant to the DTC (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL).

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.





NEXT

9.BLEED AIR FROM FUEL SYSTEM
9.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.




NEXT

10.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
10.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).


b.

Perform the injector pilot quantity learning (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)
a.

Disconnect the No. 1 or No. 2 injector driver (EDU) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C152-5 (#10) - C45-40 (#1) Always Below 1 Ω
C156-5 (#20) - C45-39 (#2) Always Below 1 Ω
C156-3 (#30) - C45-38 (#3) Always Below 1 Ω
C152-6 (#40) - C45-37 (#4) Always Below 1 Ω
C156-6 (#50) - C45-36 (#5) Always Below 1 Ω
C152-2 (#60) - C45-35 (#6) Always Below 1 Ω
C152-3 (#70) - C45-34 (#7) Always Below 1 Ω
C156-2 (#80) - C45-33 (#8) Always Below 1 Ω
C152-1 (INJF) - C45-60 (INJ1) Always Below 1 Ω
C156-1 (INF2) - C45-61 (INJ2) Always Below 1 Ω
C152-5 (#10) or C45-40 (#1) - Body ground Always 10 kΩ or higher
C156-5 (#20) or C45-39 (#2) - Body ground Always 10 kΩ or higher
C156-3 (#30) or C45-38 (#3) - Body ground Always 10 kΩ or higher
C152-6 (#40) or C45-37 (#4) - Body ground Always 10 kΩ or higher
C156-6 (#50) or C45-36 (#5) - Body ground Always 10 kΩ or higher
C152-2 (#60) or C45-35 (#6) - Body ground Always 10 kΩ or higher
C152-3 (#70) or C45-34 (#7) - Body ground Always 10 kΩ or higher
C156-2 (#80) or C45-33 (#8) - Body ground Always 10 kΩ or higher
C152-1 (INJF) or C45-60 (INJ1) - Body ground Always 10 kΩ or higher
C156-1 (INF2) or C45-61 (INJ2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C152-5 (#10) - C46-40 (#1) Always Below 1 Ω
C156-5 (#20) - C46-39 (#2) Always Below 1 Ω
C156-3 (#30) - C46-38 (#3) Always Below 1 Ω
C152-6 (#40) - C46-37 (#4) Always Below 1 Ω
C156-6 (#50) - C46-36 (#5) Always Below 1 Ω
C152-2 (#60) - C46-35 (#6) Always Below 1 Ω
C152-3 (#70) - C46-34 (#7) Always Below 1 Ω
C156-2 (#80) - C46-33 (#8) Always Below 1 Ω
C152-1 (INJF) - C46-60 (INJ1) Always Below 1 Ω
C156-1 (INF2) - C46-61 (INJ2) Always Below 1 Ω
C152-5 (#10) or C46-40 (#1) - Body ground Always 10 kΩ or higher
C156-5 (#20) or C46-39 (#2) - Body ground Always 10 kΩ or higher
C156-3 (#30) or C46-38 (#3) - Body ground Always 10 kΩ or higher
C152-6 (#40) or C46-37 (#4) - Body ground Always 10 kΩ or higher
C156-6 (#50) or C46-36 (#5) - Body ground Always 10 kΩ or higher
C152-2 (#60) or C46-35 (#6) - Body ground Always 10 kΩ or higher
C152-3 (#70) or C46-34 (#7) - Body ground Always 10 kΩ or higher
C156-2 (#80) or C46-33 (#8) - Body ground Always 10 kΩ or higher
C152-1 (INJF) or C46-60 (INJ1) - Body ground Always 10 kΩ or higher
C156-1 (INF2) or C46-61 (INJ2) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector driver (EDU) connector.


e.

Reconnect the ECM connector.



OK

12.REPLACE ECM

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.REPLACE ECM

NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER (EDU))
a.

Disconnect the injector assembly connectors.


b.

Disconnect the No. 1 or No. 2 injector driver (EDU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C141-1 - C151-6 (IJ1+) Always Below 1 Ω
C141-2 - C151-3 (IJ1-) Always Below 1 Ω
C148-1 - C155-6 (IJ2+) Always Below 1 Ω
C148-2 - C155-3 (IJ2-) Always Below 1 Ω
C142-1 - C154-4 (IJ3+) Always Below 1 Ω
C142-2 - C154-2 (IJ3-) Always Below 1 Ω
C147-1 - C151-5 (IJ4+) Always Below 1 Ω
C147-2 - C151-2 (IJ4-) Always Below 1 Ω
C143-1 - C155-5 (IJ5+) Always Below 1 Ω
C143-2 - C155-2 (IJ5-) Always Below 1 Ω
C146-1 - C151-4 (IJ6+) Always Below 1 Ω
C146-2 - C151-1 (IJ6-) Always Below 1 Ω
C144-1 - C150-4 (IJ7+) Always Below 1 Ω
C144-2 - C150-2 (IJ7-) Always Below 1 Ω
C145-1 - C155-4 (IJ8+) Always Below 1 Ω
C145-2 - C155-1 (IJ8-) Always Below 1 Ω
C141-1 or C151-6 (IJ1+) - Body ground Always 10 kΩ or higher
C141-2 or C151-3 (IJ1-) - Body ground Always 10 kΩ or higher
C148-1 or C155-6 (IJ2+) - Body ground Always 10 kΩ or higher
C148-2 or C155-3 (IJ2-) - Body ground Always 10 kΩ or higher
C142-1 or C154-4 (IJ3+) - Body ground Always 10 kΩ or higher
C142-2 or C154-2 (IJ3-) - Body ground Always 10 kΩ or higher
C147-1 or C151-5 (IJ4+) - Body ground Always 10 kΩ or higher
C147-2 or C151-2 (IJ4-) - Body ground Always 10 kΩ or higher
C143-1 or C155-5 (IJ5+) - Body ground Always 10 kΩ or higher
C143-2 or C155-2 (IJ5-) - Body ground Always 10 kΩ or higher
C146-1 or C151-4 (IJ6+) - Body ground Always 10 kΩ or higher
C146-2 or C151-1 (IJ6-) - Body ground Always 10 kΩ or higher
C144-1 or C150-4 (IJ7+) - Body ground Always 10 kΩ or higher
C144-2 or C150-2 (IJ7-) - Body ground Always 10 kΩ or higher
C145-1 or C155-4 (IJ8+) - Body ground Always 10 kΩ or higher
C145-2 or C155-1 (IJ8-) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector assembly connectors.


e.

Reconnect the No. 1 or No. 2 injector driver (EDU) connector.



OK

14.REPLACE INJECTOR DRIVER (EDU)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.REPLACE INJECTOR DRIVER (EDU)
a.

Replace the No. 1 or No. 2 injector driver (EDU) (See page Engine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.GO TO INJECTOR CIRCUIT

NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Start the engine and idle it for 5 seconds or more.


g.

Turn the GTS on.


h.

Enter the following menus: Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output again.



NEXT

END