Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL INJECTOR (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052783 1VD-FTV FUEL _0255121 FUEL INJECTOR(w/ DPF) A

1VD-FTV FUEL  FUEL INJECTOR(w/ DPF)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing an injector (including interchanging injectors between cylinders) or common rail, replace the corresponding injection pipes with new ones.

·

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Disconnect the cables from the negative (-) main battery and sub-battery terminals.


Hide 53806 3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53292A 6.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 17940D 8.REMOVE INTERCOOLER ASSEMBLY

Hide 12.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 17947B 17.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

Hide 26100G 18.REMOVE DIESEL THROTTLE BODY ASSEMBLY LH

Hide 17806 23.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 87208 25.REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 17885 26.REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 16268M 28.REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

Hide 23706 31.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 25860 32.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (for Engine Mounting)

a.
A270017

Disconnect the 2 vacuum hoses.


b.

Remove the bolt and vacuum switching valve.


Hide 25706 33.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A270018

Disconnect the 2 vacuum hoses.


b.
A270019

Remove the 3 bolts and vacuum transmitting pipe.


Hide 11225 34.REMOVE CYLINDER HEAD COVER SILENCER LH

a.
A270020

Remove the 4 bolts and cylinder head cover silencer.


Hide 23712 35.REMOVE NO. 2 FUEL INJECTOR PROTECTOR

a.
A271210

Detach the hose clamp.


b.

Remove the bolt and No. 2 fuel injector protector.


Hide 23765 38.REMOVE NO. 5 NOZZLE LEAKAGE PIPE

Hide 23820A 39.REMOVE COMMON RAIL ASSEMBLY LH

Hide 23801L 40.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 11228A 41.REMOVE CYLINDER HEAD COVER INSULATOR LH

A271217

Hide 11224 42.REMOVE CYLINDER HEAD COVER SILENCER RH

a.
A271208

Remove the 4 bolts and cylinder head cover silencer.


Hide 23711 43.REMOVE NO. 1 FUEL INJECTOR PROTECTOR

a.
A271209

Remove the bolt and No. 1 fuel injector protector.


Hide 11227 45.REMOVE CYLINDER HEAD COVER INSULATOR RH

A271216

Hide 23761A 49.REMOVE NO. 1 NOZZLE LEAKAGE PIPE

a.
A271214

Remove the 4 injector hollow screws and 4 gaskets.

Text in Illustration
V100135

Injector Hollow Screw
V100136

No. 2 Check Valve
V100137

Union Bolt


b.

Remove the No. 2 check valve from the fuel tube and No. 1 nozzle leakage pipe.


c.

Remove the union bolt and No. 1 nozzle leakage pipe.

NOTICE:
·

When removing the nozzle leakage pipe, place a cushion under the pipe.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.




Hide 50.REMOVE FUEL INJECTOR RH

a.
A271220

Remove the 4 bolts, 4 washers, 4 nozzle holder clamps, 4 nozzle holder seals and 4 fuel injectors.

HINT:

Arrange the fuel injectors, holder clamps, washers and bolts in the correct order.



b.

Remove the O-ring from each fuel injector.


c.

Remove the fuel injector seal from each fuel injector.


d.

Remove the 4 injection nozzle seats from the cylinder head sub-assembly.


Hide 23762B 51.REMOVE NO. 2 NOZZLE LEAKAGE PIPE

a.
A271219

Remove the 4 injector hollow screws and 4 gaskets.

Text in Illustration
V100135

Injector Hollow Screw
V100136

Bolt


b.

Remove the 2 bolts and No. 2 nozzle leakage pipe.

NOTICE:
·

When removing the nozzle leakage pipe, place a cushion under the pipe.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.




Hide 52.REMOVE FUEL INJECTOR LH

a.
A271221

Remove the 4 bolts, 4 washers, 4 nozzle holder clamps, 4 nozzle holder seals and 4 fuel injectors.

HINT:

Arrange the fuel injectors, holder clamps, washers and bolts in the correct order.



b.

Remove the O-ring from each fuel injector.


c.

Remove the fuel injector seal from each fuel injector.


d.

Remove the 4 injection nozzle seats from the cylinder head sub-assembly.