Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P0051  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1)  P0052  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1)  


DESCRIPTION

HINT:
·

For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

These DTCs are related to the air fuel ratio sensor, although the titles say oxygen sensor.



The air fuel ratio sensor outputs a voltage* that is proportional to the air-fuel ratio. The air fuel ratio sensor output voltage is used to control the A/F mixture.

The air fuel ratio sensor is located after the Diesel Particulate Filter (DPF) catalytic converter. This sensor has been developed based on the structure and technology of the air fuel ratio sensor that is used for gasoline engines. The cover for the sensor electrode has been modified to suit its application in a diesel engine. This change allows the sensor to function effectively in this DPF type diesel engine, and it also avoids problems with sensor temperature and particulate matter (PM).

In order to reduce PM, the ECM adjusts the air-fuel ratio to a value slightly richer than that which would otherwise be used (note that this mixture is still leaner than the stoichiometric air fuel ratio). The ECM controls these adjustments on signals from the air fuel ratio sensor.

When the ECM performs PM forced regeneration (cleaning) by adding fuel using the exhaust fuel addition injector assembly, the air fuel ratio sensor feedback is used to ensure that an appropriate air fuel ratio is maintained.

*: This voltage change occurs only inside the ECM. It is not possible to measure this voltage at the sensor. The GTS can be used to monitor this voltage.

A258975E06
5.24,1.979 5.771,2.49 false 5.052,1.792 5.719,1.979 false 5.177,1.385 5.688,1.333 false 5.406,1.271 5.729,1.094 false 5.208,1.729 5.719,1.979 false 3.208,2.25 3.854,1.906 false 3.063,2.219 2.333,1.854 false 2.583,2.604 2.708,2.802 0.125,0.198 10 false A 3.271,2.604 3.396,2.781 0.125,0.177 10 false A 1.781,1.729 2.354,1.927 0.573,0.198 10 false Element 0.677,2.073 1.552,2.292 0.875,0.219 10 false Exhaust Gas 4.875,2.635 5.635,2.833 0.76,0.198 10 false A-A Section 5.719,1.896 7.146,2.115 1.427,0.219 10 false Platinum Electrode 3.906,1.813 4.323,1.99 0.417,0.177 10 false Cover 5.802,2.427 6.094,2.625 0.292,0.198 10 false Air 5.76,0.927 6.219,1.104 0.458,0.177 10 false Heater 5.729,1.198 6.854,1.698 1.125,0.5 10 false Solid Electrolyte (Zirconia Element) 0.396,4.792 1.646,5.073 1.25,0.281 10 false AF Lambda B1S1 0.375,6.104 1.635,6.396 1.26,0.292 10 false AFS Voltage B1S1 2.031,4.865 2.198,5.073 0.167,0.208 10 false 1 2.031,4.344 2.198,4.552 0.167,0.208 10 false 2 2.042,6.24 2.208,6.448 0.167,0.208 10 false 1 2.042,6.771 2.208,6.979 0.167,0.208 10 false 0 2.031,5.385 2.198,5.594 0.167,0.208 10 false 0 2.042,5.708 2.208,5.917 0.167,0.208 10 false 2 2.302,5.698 2.531,5.948 0.229,0.25 10 false (V) 2.927,6.979 3.177,7.229 0.25,0.25 10 false 10 3.24,7.073 3.594,7.323 0.354,0.25 10 false 14.5 3.688,6.979 3.938,7.229 0.25,0.25 10 false 20 4.458,6.979 4.708,7.229 0.25,0.25 10 false 30 5.229,6.979 5.479,7.229 0.25,0.25 10 false 40 5.99,6.979 6.24,7.229 0.25,0.25 10 false 50 0.146,3.313 2.406,3.563 2.26,0.25 10 false Air-Fuel Ratio Displayed on Tester: 3.688,7.271 4.625,7.469 0.938,0.198 10 false Air-Fuel Ratio 4.094,5 6.719,5.313 2.625,0.313 10 false AF Lambda B1S1 = Air-Fuel Ratio / 14.5 2.604,8.281 3.021,8.469 0.417,0.188 10 false 0.060 4.833,8.281 5.25,8.469 0.417,0.188 10 false 0.508 5.406,8.281 5.823,8.469 0.417,0.188 10 false 0.787 5.958,8.281 6.375,8.469 0.417,0.188 10 false 0.978 6.51,8.281 6.927,8.469 0.417,0.188 10 false 1.373 4.281,8.281 4.698,8.469 0.417,0.188 10 false 0.336 3.729,8.281 4.146,8.469 0.417,0.188 10 false 0.268 3.167,8.281 3.583,8.469 0.417,0.188 10 false 0.170 2.188,8.281 2.375,8.469 0.188,0.188 10 false 0 2.115,8.729 2.448,8.917 0.333,0.188 10 false 14.5 6.031,8.729 6.365,8.917 0.333,0.188 10 false 30 2.688,8.729 3.021,8.917 0.333,0.188 10 false 15 4.906,8.729 5.24,8.917 0.333,0.188 10 false 20 6.615,8.729 6.948,8.917 0.333,0.188 10 false 50 3.802,8.729 4.135,8.917 0.333,0.188 10 false 17 3.229,8.729 3.563,8.917 0.333,0.188 10 false 16 0.375,8.729 1.323,8.979 0.948,0.25 10 false Air-Fuel Ratio 4.344,8.729 4.677,8.917 0.333,0.188 10 false 18 5.479,8.729 5.813,8.917 0.333,0.188 10 false 25 1.146,8.219 1.396,8.458 0.25,0.24 10 false (V) 0.313,8.146 1.104,8.51 0.792,0.365 10 false AFS Voltage B1S1 0.333,7.615 1.24,7.99 0.906,0.375 10 false AF Lambda B1S1 2.146,7.771 2.375,7.938 0.229,0.167 10 false 1.0 2.625,7.771 2.969,7.948 0.344,0.177 10 false 1.03 3.177,7.771 3.49,7.969 0.313,0.198 10 false 1.10 3.719,7.771 4.031,7.917 0.313,0.146 10 false 1.17 4.302,7.771 4.594,7.969 0.292,0.198 10 false 1.24 4.833,7.771 5.146,7.917 0.313,0.146 10 false 1.38 5.417,7.771 5.75,7.927 0.333,0.156 10 false 1.72 5.969,7.771 6.26,7.917 0.292,0.146 10 false 2.07 6.563,7.771 6.885,7.927 0.323,0.156 10 false 3.45 0.385,9.146 0.854,9.375 0.469,0.229 10 false HINT: 0.677,9.438 6.292,9.74 5.615,0.302 10 false *1: AFS Voltage B1S1 cannot be displayed correctly when the value is 0 V or less. 1.5,8.292 1.948,8.479 0.448,0.188 10 false -0.549 1.583,8.729 1.917,8.917 0.333,0.188 10 false 12 1.542,7.781 1.854,7.948 0.313,0.167 10 false 0.83 1.438,8.063 1.635,8.25 0.198,0.188 10 false *1 2.042,3.875 2.208,4.083 0.167,0.208 10 false 3

HINT:

The ECM provides a pulse width modulated control circuit to adjust current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.


A210271E15
3.531,0.813 3.656,0.969 3.656,0.969 3.854,0.969 false 3.583,1.281 3.667,1.375 3.667,1.375 3.865,1.375 false 0.135,0.083 0.875,0.344 0.74,0.26 10 false Reference: 0.083,0.635 0.563,1.052 0.479,0.417 10 false from Battery 2.813,0.281 4.281,0.573 1.469,0.292 10 false Air Fuel Ratio Sensor 1.74,1.427 2.031,1.625 0.292,0.198 10 false A/F 3.906,0.875 4.375,1.073 0.469,0.198 10 false Heater 3.906,1.292 4.385,1.49 0.479,0.198 10 false Sensor 5.604,2.354 6.01,2.594 0.406,0.24 10 false ECM 4.854,0.615 5.25,0.813 0.396,0.198 10 false HA1A 4.854,1.031 5.271,1.198 0.417,0.167 10 false A1A+ 4.875,1.438 5.271,1.656 0.396,0.219 10 false A1A- 6.063,1.198 6.51,1.677 0.448,0.479 10 false Duty Control 0.635,1.74 2.156,1.958 1.521,0.219 10 false from EFI MAIN 2 Relay 0.969,0.885 1.26,1.083 0.292,0.198 10 false A/F

P0031 (Bank 1), P0051 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
·

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

·

Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the GTS.


Air fuel ratio sensor heater current is 0.8 A or less when the heater operates for 4 seconds.
(1 trip detection logic)
·

Open in air fuel ratio sensor heater circuit

·

air fuel ratio sensor heater

·

A/F relay

·

ECM



P0032 (Bank 1), P0052 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 5 seconds Either condition is met (1 trip detection logic):
·

Air fuel ratio sensor heater current reaches the high limit (overcurrent is detected even though the air fuel ratio sensor heater is off)

·

Air fuel ratio sensor heater current is 0.8 A or more when the heater does not operate for 4 seconds.


·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM



Related Data List
DTC No. Data List
P0031
P0032
·

AFS Voltage B1S1

·

AF Lambda B1S1

·

Exhaust Temperature B1S1


P0052
P0053
·

AFS Voltage B2S1

·

AF Lambda B2S1

·

Exhaust Temperature B2S1



MONITOR DESCRIPTION

The inner surface of the air fuel ratio sensor element is exposed to outside air. The outer surface of the sensor element is exposed to exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations of the exhaust and the outside air. The platinum coating amplifies the voltage generation. When heated, the sensor becomes very efficient. If the temperature of the exhaust is low, without supplemental heating, the sensor will not generate useful voltage signals. The ECM controls the heating by using a duty-cycle to regulate the average current in the heater element. If the heater current is out of the normal range, the output signals of the sensor are inaccurate and the ECM cannot regulate the air-fuel ratio properly. When the heater current is out of the normal operating range, the ECM interprets this as a malfunction and stores a DTC.

WIRING DIAGRAM

A275246E02
3.135,1.729 4.51,2.073 1.375,0.344 10 false Air Fuel Ratio Sensor (for Bank 1) 1.333,5.583 1.813,5.781 0.479,0.198 10 false Battery 1.229,4.479 2.344,4.667 1.115,0.188 10 false Integration Relay 0.802,4.25 0.938,4.427 0.135,0.177 10 false 1 0.979,4.281 1.229,4.479 0.25,0.198 10 false 1C 1.583,1.427 2.292,1.604 0.708,0.177 10 false EFI NO. 3 1.354,3.417 2.198,3.583 0.844,0.167 10 false EFI MAIN 2 1.146,1.198 1.417,1.365 0.271,0.167 10 false A/F 1.635,0.438 1.781,0.604 0.146,0.167 10 false 3 0.802,0.469 0.958,0.635 0.156,0.167 10 false 5 2.26,2.25 2.479,2.417 0.219,0.167 10 false 1A 2.375,3.667 2.594,3.833 0.219,0.167 10 false 1A 0.802,0.979 0.917,1.156 0.115,0.177 10 false 2 1.635,0.969 1.75,1.146 0.115,0.177 10 false 1 2.073,2.229 2.188,2.406 0.115,0.177 10 false 4 2.427,3.458 2.542,3.635 0.115,0.177 10 false 3 3.135,1.563 3.5,1.729 0.365,0.167 10 false C159 2.979,4.594 4.354,4.938 1.375,0.344 10 false Air Fuel Ratio Sensor (for Bank 2) 2.979,4.438 3.469,4.604 0.49,0.167 10 false C158 3.396,0.469 3.51,0.646 0.115,0.177 10 false 2 4.427,0.469 4.542,0.646 0.115,0.177 10 false 1 3.396,1.26 3.51,1.438 0.115,0.177 10 false 4 4.427,1.26 4.542,1.438 0.115,0.177 10 false 3 3.573,0.458 3.802,0.625 0.229,0.167 10 false +B 3.948,0.49 4.396,0.667 0.448,0.177 10 false HAF1 3.583,1.229 3.927,1.396 0.344,0.167 10 false AF1- 3.969,1.229 4.375,1.385 0.406,0.156 10 false AF1+ 3.219,3.375 3.333,3.552 0.115,0.177 10 false 2 4.24,3.375 4.354,3.552 0.115,0.177 10 false 1 3.219,4.167 3.333,4.344 0.115,0.177 10 false 4 4.24,4.167 4.354,4.344 0.115,0.177 10 false 3 3.396,3.365 3.625,3.531 0.229,0.167 10 false +B 3.792,3.365 4.219,3.521 0.427,0.156 10 false HAF2 3.396,4.104 3.74,4.271 0.344,0.167 10 false AF2- 3.813,4.104 4.219,4.26 0.406,0.156 10 false AF2+ 5.167,0.396 5.51,0.583 0.344,0.188 10 false 45*1 5.208,0.594 5.5,0.771 0.292,0.177 10 false C45 5.844,0.49 6.25,0.656 0.406,0.167 10 false HA1A 5,1.188 5.406,1.365 0.406,0.177 10 false 102*1 5.208,1.385 5.531,1.583 0.323,0.198 10 false C45 5.833,1.271 6.24,1.438 0.406,0.167 10 false A1A+ 5.208,2.427 5.5,2.604 0.292,0.177 10 false C45 5.208,2.865 5.521,3.042 0.313,0.177 10 false 44*1 5.219,3.052 5.51,3.229 0.292,0.177 10 false A38 5.833,2.323 6.24,2.49 0.406,0.167 10 false A1A- 5.833,4.156 6.24,4.323 0.406,0.167 10 false A2A+ 5.854,5.323 6.26,5.49 0.406,0.167 10 false A2A- 5.833,3.375 6.24,3.542 0.406,0.167 10 false HA2A 5.948,5.958 6.302,6.125 0.354,0.167 10 false ECM 5.833,2.958 6.26,3.125 0.427,0.167 10 false MREL 1.156,3.854 2,4.021 0.844,0.167 10 false EFI MAIN 2 2.438,2.865 2.552,3.042 0.115,0.177 10 false 2 2.375,3.073 2.594,3.24 0.219,0.167 10 false 1A 5.531,3.052 5.823,3.229 0.292,0.177 10 false A52 5.51,2.865 5.823,3.042 0.313,0.177 10 false 44*2 5.521,0.594 5.813,0.771 0.292,0.177 10 false C46 5.49,0.396 5.865,0.594 0.375,0.198 10 false 45*2 5.51,1.375 5.854,1.573 0.344,0.198 10 false C46 5.406,1.188 5.813,1.365 0.406,0.177 10 false 102*2 5.521,2.438 5.833,2.615 0.313,0.177 10 false C46 5.021,2.25 5.427,2.427 0.406,0.177 10 false 103*1 5.427,2.25 5.833,2.427 0.406,0.177 10 false 103*2 5.198,3.479 5.49,3.656 0.292,0.177 10 false C45 5.521,3.479 5.854,3.677 0.333,0.198 10 false C46 5.177,3.302 5.5,3.479 0.323,0.177 10 false 46*1 5.5,3.302 5.802,3.479 0.302,0.177 10 false 46*2 5.208,4.271 5.542,4.469 0.333,0.198 10 false C45 5.521,4.271 5.875,4.469 0.354,0.198 10 false C46 5.021,4.094 5.427,4.271 0.406,0.177 10 false 125*1 5.427,4.094 5.833,4.271 0.406,0.177 10 false 125*2 5.198,5.438 5.521,5.615 0.323,0.177 10 false C45 5.5,5.427 5.792,5.604 0.292,0.177 10 false C46 5.01,5.24 5.417,5.417 0.406,0.177 10 false 126*1 5.406,5.24 5.813,5.417 0.406,0.177 10 false 126*2 3.354,6.021 4.094,6.198 0.74,0.177 10 false *1: for LHD 3.354,6.323 4.094,6.5 0.74,0.177 10 false *2: for RHD 0.438,1.771 0.708,1.938 0.271,0.167 10 false A/F

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (for bank 1 or bank 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION).



OK

2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR HEATER VOLTAGE)

NG

10.REPLACE AIR FUEL RATIO SENSOR
2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR HEATER VOLTAGE)
a.
U163704E01
0.113,0.221 0.309,0.372 0.195,0.151 10 *a 2.315,0.776 2.531,0.932 0.216,0.156 10 +B 0.37,1.412 0.747,1.554 0.377,0.142 10 C159 1.873,1.225 2.256,0.869 false 2.397,2.799 2.613,2.955 0.216,0.156 10 +B 1.875,3.311 2.349,2.924 false 0.433,3.475 0.810,3.617 0.377,0.142 10 C158 0.469,1.698 0.664,1.849 0.195,0.151 10 *A 0.519,3.802 0.715,3.953 0.195,0.151 10 *B

Disconnect the air fuel ratio sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C159-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
C158-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.INSPECT A/F RELAY
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C159-1 (HAF1) - C45-45 (HA1A) Always Below 1 Ω
C158-1 (HAF2) - C45-46 (HA2A) Always Below 1 Ω
C159-1 (HAF1) or C45-45 (HA1A) - Body ground Always 10 kΩ or higher
C158-1 (HAF2) or C45-46 (HA2A) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C159-1 (HAF1) - C46-45 (HA1A) Always Below 1 Ω
C158-1 (HAF2) - C46-46 (HA2A) Always Below 1 Ω
C159-1 (HAF1) or C46-45 (HA1A) - Body ground Always 10 kΩ or higher
C158-1 (HAF2) or C46-46 (HA2A) - Body ground Always 10 kΩ or higher




OK

4.REPLACE ECM

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.INSPECT A/F RELAY

OK

6.CHECK HARNESS AND CONNECTOR (A/F RELAY - A/F SENSOR)

NG

11.REPLACE A/F RELAY
6.CHECK HARNESS AND CONNECTOR (A/F RELAY - A/F SENSOR)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the A/F relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-2 (+B) - A/F relay terminal 3 Always Below 1 Ω
C158-2 (+B) - A/F relay terminal 3 Always Below 1 Ω
C159-2 (+B) or A/F relay terminal 3 - Body ground Always 10 kΩ or higher
C158-2 (+B) or A/F relay terminal 3 - Body ground Always 10 kΩ or higher




OK

7.INSPECT INTEGRATION RELAY (EFI MAIN 2)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.INSPECT INTEGRATION RELAY (EFI MAIN 2)
a.

Inspect the integration relay (EFI MAIN 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

8.CHECK HARNESS AND CONNECTOR (A/F RELAY - INTEGRATION RELAY, BATTERY)

NG

12.REPLACE INTEGRATION RELAY
8.CHECK HARNESS AND CONNECTOR (A/F RELAY - INTEGRATION RELAY, BATTERY)
a.

Remove the A/F relay from the engine room relay block and junction block assembly.


b.

Remove the integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A/F relay terminal 5 - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A/F relay terminal 1 - 1A-4 Always Below 1 Ω
A/F relay terminal 2 - Body ground Always Below 1 Ω
A/F relay terminal 1 or 1A-4 - Body ground Always 10 kΩ or higher




OK

9.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)
a.

Remove the integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
1A-2 - A38-44 (MREL) Always Below 1 Ω
1A-2 or A38-44 (MREL) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
1A-2 - A52-44 (MREL) Always Below 1 Ω
1A-2 or A52-44 (MREL) - Body ground Always 10 kΩ or higher




OK

14.CHECK ECM POWER SOURCE CIRCUIT

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE AIR FUEL RATIO SENSOR

When DTC P0031 or P0032 is output:

·

Replace the air fuel ratio sensor (for bank 1) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).


When DTC P0051 or P0052 is output:

·

Replace the air fuel ratio sensor (for bank 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE A/F RELAY
a.

Replace the A/F relay.



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE INTEGRATION RELAY
a.

Replace the integration relay (EFI MAIN 2).



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CHECK ECM POWER SOURCE CIRCUIT

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

HINT:

"Exhaust Temperature B1S1" and "Exhaust Temperature B2S1" on the GTS screen should be 200°C (392°F) or higher.



g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


ii.

Input DTC P0031, P0032, P0052 or P0053.


iii.

Check that STATUS is NORMAL.

HINT:
·

If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.

·

If STATUS is INCOMPLETE or N/A, DTC judgment is incomplete. Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more again.






NEXT

END