Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0116  Engine Coolant Temperature Circuit Range / Performance Problem  


DESCRIPTION

A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.

The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.

P0116
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
With the engine coolant temperature below 60°C (140°F), start the engine and idle it for 5 minutes. Then drive the vehicle at a speed of 40 km/h (25 mph) or more for a total of 5 minutes or more and check that the engine coolant temperature changes by 1°C (1.8°F) or more. When engine is started cold and warmed up, the engine coolant temperature sensor value does not change (2 trip detection logic).
·

Thermostat

·

Engine coolant temperature sensor


After the warmed up engine is stopped and the next cold engine start is performed, the engine coolant temperature sensor value does not change (2 trip detection logic).

Related Data List
DTC No. Data List
P0116 Coolant Temp

HINT:

If DTC P0116 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




MONITOR DESCRIPTION

Engine coolant temperature sensor cold start monitor

When a cold engine start is performed and then the engine is warmed up, if the engine coolant temperature sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.


Engine coolant temperature sensor soak monitor

If the engine coolant temperature sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See Page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
P0116 is output A
P0116 and other DTCs are output B



A

2.INSPECT THERMOSTAT

B

2.INSPECT THERMOSTAT

OK

3.REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

4.REPLACE THERMOSTAT
3.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL).



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE THERMOSTAT
a.


NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Coolant Temp.


d.

Check that the engine coolant temperature is 60°C (140°F) or less.


e.

Start the engine.


f.

Idle the engine for 5 minutes, and then drive the vehicle at a speed of 40 km/h (25 mph) or more for a total of 5 minutes or more.


g.

Check that the engine coolant temperature changes by 1°C (1.8°F) or more.



NEXT

END