A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| With the engine coolant temperature below 60°C (140°F), start the engine and idle it for 5 minutes. Then drive the vehicle at a speed of 40 km/h (25 mph) or more for a total of 5 minutes or more and check that the engine coolant temperature changes by 1°C (1.8°F) or more. | When engine is started cold and warmed up, the engine coolant temperature sensor value does not change (2 trip detection logic). | ·
Thermostat ·
Engine coolant temperature sensor |
| After the warmed up engine is stopped and the next cold engine start is performed, the engine coolant temperature sensor value does not change (2 trip detection logic). |
| DTC No. | Data List |
|---|---|
| P0116 | Coolant Temp |
If DTC P0116 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
When a cold engine start is performed and then the engine is warmed up, if the engine coolant temperature sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.
If the engine coolant temperature sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See Page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0116 is output | A |
| P0116 and other DTCs are output | B |
A
B
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART)
Inspect the thermostat (See page Engine / Hybrid System>1VD-FTV (COOLING)>THERMOSTAT>INSPECTION).
OK
NG
Replace the engine coolant temperature sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL).
NEXT
Replace the thermostat (See page Engine / Hybrid System>1VD-FTV (COOLING)>THERMOSTAT>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / Coolant Temp.
Check that the engine coolant temperature is 75°C (167°F) or less.
Start the engine.
Idle the engine for 5 minutes, and then drive the vehicle at a speed of 40 km/h (25 mph) or more for a total of 5 minutes or more.
Check that the engine coolant temperature changes by 1°C (1.8°F) or more.
NEXT