1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
28800
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the cables from the negative (-) main battery and sub-battery terminals.
53292A
3.REMOVE UPPER RADIATOR SUPPORT SEAL
4.REMOVE FRONT WHEEL RH
53736G
5.REMOVE FRONT FENDER APRON SEAL FRONT RH
53806
6.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
7.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
51405A
8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
9.DRAIN ENGINE COOLANT
82113
10.REMOVE NO. 3 ENGINE ROOM WIRE
Disconnect the 4 wire harness clamps.
Remove the 2 nuts and No. 3 engine room wire.
12601E
11.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)
17705
12.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
17881
13.REMOVE NO. 1 AIR CLEANER HOSE
17861
14.REMOVE INTAKE AIR CONNECTOR
44360
15.REMOVE VANE PUMP OIL RESERVOIR ASSEMBLY
Insert a screwdriver between the reservoir and oil reservoir bracket, push the claw, and then disconnect the reservoir by pulling it upwards.
44369A
16.REMOVE NO. 1 OIL RESERVOIR BRACKET
Remove the 2 bolts and bracket.
16470
17.REMOVE RADIATOR RESERVOIR ASSEMBLY
Disconnect the 2 hoses.
Remove the 3 bolts and radiator reservoir.
44310
18.REMOVE VANE PUMP ASSEMBLY
Remove the 2 nuts and vane pump.
Remove the O-ring from the vane pump.
16571C
19.DISCONNECT NO. 1 RADIATOR HOSE
16572D
20.DISCONNECT NO. 2 RADIATOR HOSE
21.REMOVE V-RIBBED BELT (w/ Viscous Heater)
22.REMOVE NO. 1 IDLER PULLEY (w/ Viscous Heater)
23.REMOVE NO. 3 IDLER PULLEY (w/ Viscous Heater)
16361A
24.REMOVE V-RIBBED BELT
32942
25.REMOVE OIL COOLER TUBE (for Automatic Transmission)
16711
26.REMOVE FAN SHROUD WITH FAN
Loosen the 4 nuts holding the fluid coupling fan.
Remove the 2 bolts holding the fan shroud.
Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the fluid coupling fan.
16371
27.REMOVE FAN PULLEY
87208
28.REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)
Remove the 4 bolts and disconnect the heater water pipe from the viscous heater with magnet clutch.
87120G
29.REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (w/ Viscous Heater)
30.REMOVE NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)
Remove the bolt and No. 1 idler pulley bracket.
16321
31.REMOVE WATER INLET
Disconnect the No. 2 oil cooler hose from the water pump and clamp.
Remove the 4 bolts and water inlet.
16331A
32.REMOVE THERMOSTAT
Remove the thermostat.
Remove the gasket from the thermostat.