Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P1271  Fuel Regulator Circuit Malfunction (EDU Drive)  P1272  Fuel Pressure Regulator Malfunction  


DESCRIPTION

The ECM controls the internal fuel pressure of the common rail assembly by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail assembly. Also, the pressure discharge valve opens when the engine switch is turned off to allow prompt discharge of the common rail internal pressure and so that the engine stops smoothly.

HINT:
·

For more information on the pressure discharge valve and common rail system, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

For more information on the injector driver, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

·

If P1271 and/or P1272 is present, refer to the DTC chart for the fuel system (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).



A208468E03
0.057,0.035 4.208,0.212 4.151,0.177 10 Pressure Discharge Valve Operation Due to Sudden Deceleration: 0.928,0.378 2.056,0.722 1.128,0.343 10 Accelerator Pedal Opening Angle 0.403,1.389 2.038,1.552 1.635,0.163 10 Pressure Discharge Valve 1.132,2.292 2.044,2.455 0.913,0.163 10 Fuel Pressure 2.595,0.546 2.980,0.709 0.385,0.163 10 Open 4.139,1.391 4.524,1.554 0.385,0.163 10 Open 2.595,1.156 3.077,1.319 0.482,0.163 10 Closed 4.139,0.722 4.659,0.885 0.519,0.163 10 Closed 4.22,2.134 6.133,2.276 1.913,0.142 10 w/o Pressure Discharge Valve 1.673,2.706 3.482,2.848 1.809,0.142 10 w/ Pressure Discharge Valve 2.079,3.063 3.430,3.226 1.350,0.163 10 Target Fuel Pressure 3.932,3.287 4.942,3.450 1.010,0.163 10 Time Reduction 3.323,3.528 3.674,3.677 0.350,0.149 10 Time 3.73,2.783 3.499,2.783 false 3.685,3 3.495,3.14 3.495,3.14 3.415,3.14 false 3.898,2.424 4.087,2.224 4.087,2.224 4.183,2.224 false

A205138E09
3.448,1.802 2.854,2.5 2.854,2.5 2.979,2.5 false 4.25,2.125 5.104,1.76 5.104,1.76 5.25,1.76 false 0.042,0.073 3.563,0.25 3.521,0.177 10 false Cross Section Diagram of Pressure Discharge Valve: 0.542,1.646 1.802,2 1.26,0.354 10 false From Common Rail (High Pressure) 1.875,0.479 4.354,0.667 2.479,0.188 10 false Return to Fuel Tank (Low Pressure) 3.042,2.427 3.406,2.594 0.365,0.167 10 false Valve 5.302,1.688 5.885,1.854 0.583,0.167 10 false Solenoid

P1271
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) to OFF
and
Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal
When either condition below is met a certain number of times (0.5 seconds) (1 trip detection logic):
·

Open or short in pressure discharge valve circuit.

·

There is no valve opening confirmation (IJf) signal from the injector driver to the ECM for a specific number of times consecutively despite the ECM sending valve opening command (PRD) signals after the engine is started.


·

Open or short in pressure discharge valve circuit

·

Pressure discharge valve (common rail assembly (for bank 2))

·

No. 1 injector driver



P1272
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) to OFF Pressure discharge valve does not open.
Actual pressure decreasing rate deviates from the simulated pressure decreasing rate after the ignition switch is turned off (2 trip detection logic).
·

Open or short in pressure discharge valve circuit (P1271 is stored simultaneously)

·

Pressure discharge valve (common rail assembly (for bank 2))

·

No. 1 injector driver

·

ECM



Related Data List
DTC No. Data List
P1271
P1272
·

Common Rail Pressure

·

Target Common Rail Pressure

·

Pressure Discharge Valve



HINT:
·

After confirming DTC P1271 and/or P1272, check the fuel pressure inside the common rail by entering the following menus: Engine and ECT / Data List / Common Rail Pressure.

·

P1271:

After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P1271 is not output.

·

P1272:

After clearing the DTC, start and stop the engine twice (wait 30 seconds or more after turning the ignition switch off before starting the engine the second time), and then confirm that P1272 is not stored.


Reference
Engine Speed Common Rail Pressure (kPa)
Idling Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure
2500 rpm (No engine load)

Results of Real-vehicle Check
Condition Common Rail Pressure (Idling) Common Rail Pressure (1 Second after Engine Stopped)
Pressure discharge valve normal 35000 kPa 500 kPa
Open in pressure discharge valve circuit 35000 kPa 30000 kPa


MONITOR DESCRIPTION

P1271 (Open or short in pressure discharge valve circuit):

This DTC will be stored if there is no valve opening confirmation (IJf) signal sent from the injector driver to the ECM despite the ECM commanding the injector driver to open the pressure discharge valve. This DTC refers to an open or short circuit malfunction of the pressure discharge valve circuit, not a malfunction in which a valve is stuck open or closed.

The injector driver monitors the current supplied to the pressure discharge valve to verify that the current flows into the valve. If the current exceeds the specified level, the injector driver interprets this as the IJf signal being low. If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the engine switch is turned off.

A208469E05
0.112,0.053 1.438,0.210 1.326,0.157 10 P1271 Malfunction: 0.164,1.86 1.820,2.225 1.656,0.364 10 Pressure Discharge Valve Command Signal 1.933,1.958 2.312,2.142 0.378,0.184 10 PRD 2.344,0.198 2.722,0.382 0.378,0.184 10 ECM 5.502,0.194 6.473,0.378 0.971,0.184 10 Injector Driver 2.832,1.343 3.099,1.526 0.267,0.184 10 On 3.295,1.717 3.545,1.901 0.250,0.184 10 Off 4.182,2.412 4.955,2.596 0.773,0.184 10 Abnormal 3.12,3.286 3.653,3.470 0.532,0.184 10 Normal 0.164,2.589 1.820,2.953 1.656,0.364 10 Pressure Discharge Valve Confirmation Signal 2.053,2.687 2.285,2.871 0.232,0.184 10 IJf 3.313,1.164 4.856,1.348 1.542,0.184 10 Confirmation Signal (IJf) 3.313,0.455 5.273,0.638 1.959,0.184 10 Command Signal (PRD) 3.863,2.752 3.982,2.487 3.982,2.487 4.137,2.487 false 3.856,3.092 3.779,3.37 3.779,3.37 3.646,3.37 false


P1272 (Pressure discharge valve stuck closed):

The pressure discharge valve will open and discharge the internal fuel pressure from the common rail to the fuel tank when the engine switch is turned off. In this event, the ECM compares the actual drop rate of the internal fuel pressure and the target drop rate. If the ECM judges that the actual drop rate is smaller than the target, the ECM then determines that the valve is stuck closed and stores this DTC. This DTC will be stored if the internal fuel pressure does not drop to the target after the engine switch has been turned off.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The ECM continues operating in fail-safe mode until the engine switch is turned off.


MONITOR STRATEGY

P1271
Required sensors Injector driver
Frequency of operation Continuous
Duration 3 seconds
MIL operation 1 driving cycle

P1272
Required sensors Fuel pressure sensor
Frequency of operation Once per driving cycle
Duration 1 second
MIL operation 2 driving cycles

TYPICAL ENABLING CONDITIONS

P1271
Specification
The vehicle is driven at 50 km/h (31 mph) in 3rd gear, and then decelerated by complete release of the accelerator pedal 3 times.

P1272
Item Specification
Minimum Maximum
Common Rail Pressure 30000 kPa (306 kgf/cm2, 4350 psi) -
Fuel temperature 0°C (32°F) -
Battery voltage 11 V -
The monitor will not run if the fuel pressure sensor, pressure discharge valve circuit or fuel temperature sensor is malfunctioning.

TYPICAL MALFUNCTION THRESHOLDS

P1271
Specification
There are no confirmation signals from the injector driver for a specific number of times consecutively, despite the ECM sending command signals regularly during deceleration.

P1272
Specification
The internal pressure stays beyond the specified level after the engine switch is turned off.

WIRING DIAGRAM

A301619E05
0.156,3.073 1.99,3.24 1.833,0.167 10 false No. 1 Injector Driver (EDU) 1.5,0.365 1.604,0.531 0.104,0.167 10 false 1 5.906,3.198 6.24,3.365 0.333,0.167 10 false ECM 5.563,0.438 5.74,0.604 0.177,0.167 10 false 61 5.865,3.031 6.792,3.229 0.927,0.198 10 false C45*1, C46*2 5.854,0.542 6.198,0.698 0.344,0.156 10 false INJ1 0.99,1.208 1.333,1.385 0.344,0.177 10 false PRD 0.938,1.885 1.323,2.042 0.385,0.156 10 false RLF- 0.917,2.417 1.323,2.583 0.406,0.167 10 false RLF+ 3.552,2.698 4.063,2.865 0.51,0.167 10 false z68 3.552,2.844 5.208,3.01 1.656,0.167 10 false Pressure Discharge Valve 4.781,2.323 4.896,2.479 0.115,0.156 10 false 1 3.417,2.313 3.531,2.469 0.115,0.156 10 false 2 5.854,1.188 6.26,1.354 0.406,0.167 10 false PRD 5.563,1.115 5.771,1.281 0.208,0.167 10 false 54 1.375,1.896 1.75,2.052 0.375,0.156 10 false C153 1.385,0.563 1.76,0.719 0.375,0.156 10 false C152 1.51,1.031 1.656,1.198 0.146,0.167 10 false 4 0.99,0.552 1.333,0.708 0.344,0.156 10 false INJF 1.51,1.688 1.615,1.875 0.104,0.188 10 false 2 1.51,2.208 1.646,2.375 0.135,0.167 10 false 1 1.385,1.229 1.76,1.385 0.375,0.156 10 false C152 1.385,2.406 1.76,2.563 0.375,0.156 10 false C153 2.469,3.125 3.26,3.313 0.792,0.188 10 false *1: for LHD 2.469,3.385 3.26,3.625 0.792,0.24 10 false *2: for RHD 3.583,2.313 4.063,2.479 0.479,0.167 10 false COM3 4.406,2.313 4.74,2.479 0.333,0.167 10 false RLV


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:
·

After completing repairs, confirm that P1271 and/or P1272 does not recur.

·

If P062D (No. 1 injector driver) and P1271 are present simultaneously, there is an open in the INJF wire harness between the injector driver and ECM, or there is an open in the wire harness for both an injector assembly and the pressure discharge valve.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK IF DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


f.

Enter the following menus: Engine and ECT / Trouble Codes.


g.

Read the pending DTCs.

Result
Result Proceed to
P1272 is output A
P1271 is output B
P1271 and P1272 are output B
Other DTCs are output C



A

2.PERFORM ACTIVE TEST USING GTS (PRESSURE DISCHARGE VALVE CHECK)

B

3.INSPECT COMMON RAIL ASSEMBLY (FOR BANK 2) (PRESSURE DISCHARGE VALVE RESISTANCE)

C

2.PERFORM ACTIVE TEST USING GTS (PRESSURE DISCHARGE VALVE CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Engine and ECT / Utility / Pressure Discharge Valve Check.


e.

Select the check type for "Valve Check for Graph".


f.

Press "Start" and perform "Pressure Discharge Valve Check".

HINT:

For more information about "Pressure Discharge Valve Check / Valve Check for Graph", refer to System Check (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DATA LIST / ACTIVE TEST).



g.

Check the engine speed and fuel pressure when the pressure discharge valve is turned from off to on.

OK:
Pressure Discharge Valve OFF ON
Engine Speed Idling: 550 to 650 rpm Changes to 0 rpm
Fuel Pressure Idling: 27000 to 49000 kPa Changes to 0 kPa


HINT:

When the system is normal, the following changes will be displayed on the GTS.

A267387E01
0.633,0.249 2.240,0.439 1.607,0.190 10 Fuel Pressure (kPa) 0.938,2.007 1.073,2.197 0.135,0.190 10 0 0.619,0.974 1.067,1.164 0.448,0.190 10 30000 1.057,2.073 1.123,2.073 false 1.057,1.757 1.123,1.757 false 1.057,1.384 1.123,1.384 false 1.057,1.052 1.123,1.052 false 0.619,1.321 1.067,1.511 0.448,0.190 10 20000 0.619,1.696 1.067,1.885 0.448,0.190 10 10000 0.633,3.149 2.240,3.339 1.607,0.190 10 Engine Speed (rpm) 0.938,4.907 1.073,5.097 0.135,0.190 10 0 0.787,3.782 1.087,3.972 0.300,0.190 10 600 1.057,4.973 1.123,4.973 false 1.057,4.607 1.122,4.607 false 1.057,4.206 1.123,4.206 false 1.057,3.86 1.123,3.86 false 0.787,4.143 1.087,4.332 0.300,0.190 10 400 0.787,4.546 1.087,4.735 0.300,0.190 10 200 0.628,6.119 2.313,6.309 1.685,0.190 10 Pressure Discharge Valve 0.741,7.886 1.067,8.076 0.326,0.190 10 OFF 1.052,7.951 1.119,7.951 false 1.052,7.363 1.122,7.363 false 0.783,7.295 1.082,7.485 0.300,0.190 10 ON




OK

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

12.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 2) (PRESSURE DISCHARGE VALVE)
3.INSPECT COMMON RAIL ASSEMBLY (FOR BANK 2) (PRESSURE DISCHARGE VALVE RESISTANCE)
a.

Inspect the common rail assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - NO. 1 INJECTOR DRIVER)

NG

12.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 2) (PRESSURE DISCHARGE VALVE)
4.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - NO. 1 INJECTOR DRIVER)
a.

Disconnect the No. 1 injector driver connector.


b.

Disconnect the pressure discharge valve connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z68-2 (COM3) - C153-2 (RLF+) Always Below 1 Ω
z68-1 (RLV) - C153-1 (RLF-) Always Below 1 Ω
z68-2 (COM3) or C153-2 (RLF+) - Body ground Always 10 kΩ or higher
z68-1 (RLV) or C153-1 (RLF-) - Body ground Always 10 kΩ or higher



d.

Reconnect the No.1 injector driver connector.


e.

Reconnect the pressure discharge valve connector.



OK

5.CHECK HARNESS AND CONNECTOR (NO. 1 INJECTOR DRIVER - ECM)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (NO. 1 INJECTOR DRIVER - ECM)
a.

Disconnect the No. 1 injector driver connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C152-4 (PRD) - C45-54 (PRD) Always Below 1 Ω
C152-1 (INJF) - C45-61 (INJ1) Always Below 1 Ω
C152-4 (PRD) or C45-54 (PRD) - Body ground Always 10 kΩ or higher
C152-1 (INJF) or C45-61 (INJ1) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C152-4 (PRD) - C46-54 (PRD) Always Below 1 Ω
C152-1 (INJF) - C46-61 (INJ1) Always Below 1 Ω
C152-4 (PRD) or C46-54 (PRD) - Body ground Always 10 kΩ or higher
C152-1 (INJF) or C46-61 (INJ1) - Body ground Always 10 kΩ or higher



d.

Reconnect the No. 1 injector driver connector.


e.

Reconnect the ECM connector.



OK

6.INSPECT NO. 1 INJECTOR DRIVER (POWER SOURCE CIRCUIT)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.INSPECT NO. 1 INJECTOR DRIVER (POWER SOURCE CIRCUIT)
a.
U163300E01
0.843,1.668 1.050,1.825 0.207,0.157 10 +B 0.768,0.516 1.102,0.667 0.334,0.151 10 GND 0.209,0.369 0.391,0.530 0.182,0.161 10 *a 0.307,1.054 0.704,1.217 0.397,0.163 10 C150 1.398,1.011 1.16,0.598 false 1.398,1.355 1.078,1.668 false

Disconnect the No. 1 injector driver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C150-3 (+B) - C150-1 (GND) Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to No. 1 injector Driver)


c.

Reconnect the No. 1 injector driver connector.



OK

7.REPLACE NO. 1 INJECTOR DRIVER

NG

10.GO TO INJECTOR CIRCUIT
7.REPLACE NO. 1 INJECTOR DRIVER
a.

Replace the No. 1 injector driver (See page Engine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).



NEXT

8.CHECK IF DTC OUTPUT RECURS (DTC P1271 OR P1272)
8.CHECK IF DTC OUTPUT RECURS (DTC P1271 OR P1272)
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


f.

Enter the following menus: Engine and ECT / Trouble Codes.


g.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


ii.

Input DTC P1271 and P1272.


iii.

Check the DTC judgment result.

Result
GTS Display Result Proceed to
Pending DTC P1271 or P1272 is output B
All Readiness NORMAL A
ABNORMAL B

HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.





A

END

B

11.REPLACE ECM
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.GO TO INJECTOR CIRCUIT

NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE ECM

NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 2) (PRESSURE DISCHARGE VALVE)
a.

Replace the common rail assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

13.BLEED AIR FROM FUEL SYSTEM
13.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.




NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG).


e.

Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.


f.

Enter the following menus: Engine and ECT / Trouble Codes.


g.

Confirm that the pending DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


ii.

Input DTC P1271 and P1272.


iii.

Check the DTC judgment result.

HINT:

If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.





NEXT

END