Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  Active Control Engine Mount System  


DESCRIPTION

The Active Control Engine Mount (ACM) system decreases engine vibration at low engine speed using the VSV for engine mount. The VSV is controlled by a pulse signal transmitted to the VSV from the ECM. The frequency of this pulse signal is matched to the engine speed to decrease engine vibration.

WIRING DIAGRAM

A182519E02
0.248,1.298 1.782,1.477 1.533,0.179 10 from EFI MAIN 2 relay 0.947,2.769 1.697,2.934 0.751,0.165 10 *1: for LHD 0.947,3.049 1.697,3.215 0.751,0.165 10 *2: for RHD 2.511,1.118 3.172,1.279 0.661,0.161 10 EFI NO. 2 2.595,1.379 2.714,1.544 0.119,0.165 10 1 2.96,1.379 3.079,1.544 0.119,0.165 10 2 3.665,1.379 3.784,1.544 0.119,0.165 10 1 4.41,1.379 4.529,1.544 0.119,0.165 10 2 3.391,1.639 3.685,1.793 0.295,0.154 10 C81 3.391,1.784 4.834,1.963 1.443,0.179 10 VSV for Engine Mount 5.568,1.289 5.918,1.435 0.350,0.147 10 ACM 5.311,1.379 5.508,1.547 0.197,0.167 10 52 5.647,2.755 6.553,2.920 0.906,0.165 10 A38*1, A52*2 5.647,2.905 6.007,3.065 0.360,0.161 10 ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Move the shift lever to N or P.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the ACM Inhibit.


e.

Hold the top part of the steering wheel, and turn the Active Test from OFF to ON. Check the engine vibration.

Result:
Engine Vibration Proceed to
Increases A
Does not increase B




B

2.CHECK VACUUM

A

2.CHECK VACUUM
a.

Check if the vacuum hose cap is missing, if the hose is damaged, and if the air and vacuum hoses have looseness, disconnection or blockage.

OK:

Vacuum hose cap is not missing and hoses are normal.




OK

3.INSPECT VSV FOR ENGINE MOUNT

NG

REPLACE VACUUM HOSE

3.INSPECT VSV FOR ENGINE MOUNT

OK

4.CHECK HARNESS AND CONNECTOR (VSV FOR ENGINE MOUNT - ECM, EFI NO. 2 FUSE - VSV FOR ENGINE MOUNT)

NG

4.CHECK HARNESS AND CONNECTOR (VSV FOR ENGINE MOUNT - ECM, EFI NO. 2 FUSE - VSV FOR ENGINE MOUNT)
a.

Disconnect the VSV for engine mount connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C81-2 - A38-52 (ACM) Always Below 1 Ω
C81-2 or A38-52 (ACM) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C81-2 - A52-52 (ACM) Always Below 1 Ω
C81-2 or A52-52 (ACM) - Body ground Always 10 kΩ or higher



d.

Remove the EFI NO. 2 fuse from the engine room relay block.

A384702E01
1.563,0.885 2,1.146 0.438,0.26 0.365,0.063 2.667,0.448 2.302,0.385 10 false Front view of wire harness connector: (to VSV for Engine Mount) 3.375,0.052 5.75,0.438 2.375,0.385 10 false Front view of wire harness connector: (to Engine Room Relay Block) 1.635,0.927 2.01,1.125 0.375,0.198 10 false C81 4.646,2.313 5.438,2.51 0.792,0.198 10 false EFI NO. 2


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI NO. 2 fuse (2) - C81-1 Always Below 1 Ω




OK

5.INSPECT ENGINE MOUNTING INSULATOR FRONT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ENGINE MOUNTING INSULATOR FRONT
a.

Inspect the engine mounting insulator front (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ACTIVE CONTROL ENGINE MOUNT>INSPECTION).



OK

NG