Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P20CF  Exhaust Aftertreatment Fuel Injector "A" Stuck Open  P20D5  Exhaust Aftertreatment Fuel Injector "B" Stuck Open  


DESCRIPTION

Refer to DTC P200C (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P200C).

P20CF (Bank 1), P20D5 (Bank 2)
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration AF Lambda B1S1, B2S1 is less than 0.85 for a certain time while the engine is running
(1 trip detection logic)
·

Open or short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

Fuel filter element sub-assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/exhaust system

·

After treatment control system



Related Data List
DTC No. Data List
P20CF AF Lambda B1S1
Exhaust Temperature B1S2
Exhaust Temperature B1S3
P20D5 AF Lambda B2S1
Exhaust Temperature B2S2
Exhaust Temperature B2S3

MONITOR DESCRIPTION

The ECM monitors the air fuel ratio to detect whether the exhaust fuel addition injector assembly is stuck open.

If the air fuel ratio becomes too rich, the ECM determines that the exhaust fuel addition injector assembly is stuck open, illuminates the MIL and limits engine output.

A248903E05
2.969,1.615 2.573,2.354 2.573,2.354 2.49,2.354 false 0.177,0.167 1.688,0.469 1.51,0.302 10 false Malfunction Detection: 0.146,1.031 1.458,1.406 1.313,0.375 10 false AF Lambda B1S1 or AF Lambda B2S1 3.854,1.979 4.927,2.313 1.073,0.333 10 false MIL Goes On 1.885,2.271 2.615,2.51 0.729,0.24 10 false Abnormal 5.552,1.031 6.656,1.323 1.104,0.292 10 false Normal 5.75,1.49 6.958,1.875 1.208,0.385 10 false P20CF and P20D5 Threshold 1.792,0.604 2.219,0.875 0.427,0.271 10 false Lean 1.802,1.354 2.208,1.615 0.406,0.26 10 false Rich

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P20CF OR P20D5)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
P20CF or P20D5 is output A
P20CF or P20D5 and other DTCs are output B

HINT:
·

When DTC P20CF or P20D5 and the following DTCs are output, uncombusted fuel adhesion to the air fuel ratio sensor due to air fuel ratio sensor malfunction, fuel leaks, insufficient combustion due to malfunctions of parts (intake, exhaust or injection system), or an exhaust fuel addition injector assembly wiring malfunction is may be the cause. Therefore, diagnose the following DTCs first.

·

DTCs for the air fuel ratio sensor (for bank 1) are P2237, P2238, P2239, P2252 and P2253 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P2237).

·

DTCs for the air fuel ratio sensor (for bank 2) are P2240, P2241, P2242, P2255 and P2256 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P2237).

·
·

DTCs an the exhaust fuel addition injector assembly wiring malfunction are P20CD and P20D3 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P20CD).

·

A DTC for an EGR valve flow malfunction is P0400 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P0400).

·

DTCs for an EGR valve stuck being open are P042E and P045E (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P042E).





A

2.CHECK FOR WHITE SMOKE (WHITE SMOKE AND ODOR)

B

10.GO TO DTC CHART
2.CHECK FOR WHITE SMOKE (WHITE SMOKE AND ODOR)
NOTICE:

If a fuel odor is noted from the white smoke during the inspection, there may be fuel leaks from the exhaust fuel addition injector assembly.


a.

Disconnect the cable from the negative (-) battery terminal or remove the EFI MAIN fuse for 1 minute or more.


b.

Start the engine and race it to 3000 rpm several times.


c.

Check for white smoke in the exhaust gas. If found, check for a fuel odor or the smell of burning oil.

Result
Result Proceed to
White smoke and a fuel odor are present. A
White smoke and a smell of burning oil are present. B
Except above C



A

3.PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSOR INSPECTION)

B

11.CHECK AND REPLACE TURBOCHARGER SUB-ASSEMBLY

C

7.CHECK FUEL INJECTION SYSTEM
3.PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSOR INSPECTION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Engine and ECT / Data List / AF Lambda B1S1, AF Lambda B2S1, Exhaust Temperature B1S3 and Exhaust Temperature B2S3.


e.

Drive the vehicle until the values of "Exhaust Temperature B1S3" and "Exhaust Temperature B2S3" become 300°C (572°F) or more to activate the air fuel ratio sensors.

HINT:

Activation of the air fuel ratio sensor can be checked by confirming whether the value of "AF Lambda B1S1" or "AF Lambda B2S1" has changed from 1.99.



f.

Check that there is no problem with driving performance such as hesitation, knocking, rough idling, insufficient power and acceleration stumbling, or white smoke in emissions.

A241156E07
6.5,1.135 6.385,1.135 false 6.385,1.135 5.99,1.865 false 5.427,2.896 5.292,2.896 5.292,2.896 5.198,2.792 false 6.313,3.083 6.25,3.083 false 6.25,3.083 5.938,3.563 false 5.948,4.323 5.823,4.323 5.823,4.323 5.646,4.146 false 6.531,1.073 7.01,1.365 0.479,0.292 10 false Normal 5.479,2.813 6.125,3.104 0.646,0.292 10 false Abnormal 6.385,3 6.865,3.292 0.479,0.292 10 false Normal 6.021,4.24 6.667,4.531 0.646,0.292 10 false Abnormal 3.427,0.094 5.979,0.469 2.552,0.375 10 false Air Fuel Ratio Sensor Starter Operation 4.281,0.677 6.844,1.052 2.563,0.375 10 false After Air Fuel Ratio Sensor Activation 1.833,1.167 2.25,1.333 0.417,0.167 10 false 1.99 1.906,2.542 2.25,2.729 0.344,0.188 10 false 1.0 1.906,4.104 2.25,4.271 0.344,0.167 10 false 0 V 0.615,1.625 1.781,2.021 1.167,0.396 10 false AF Lambda B1S1, AF Lambda B2S1 0.615,3.438 1.885,4.135 1.271,0.698 10 false AFS Voltage B1S1, AFS Voltage B2S1

HINT:
·

The air fuel ratio sensor does not operate until the vehicle has been driven for a period of time with an exhaust gas temperature of 200°C (392°F) or more.

·

Perform diagnosis when the air fuel ratio sensor is operating and active.

·

The normal condition in the illustration is only an example. "AF Lambda B1S1" and "AF Lambda B2S1" change depending on driving conditions. If they change within the range of values more than 1.0, they are normal.



Result
Result Proceed to
There is no problem with driving performance such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, but excessive white smoke is present in the exhaust gas A
Except above B

HINT:

If white smoke is present in the exhaust gas without any driving performance problems such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, fuel injected due to a malfunction in the exhaust fuel addition injector assembly should be suspected as the cause of the white smoke.




A

4.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

7.CHECK FUEL INJECTION SYSTEM
4.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

When DTC P20CF is output:

·

Replace the exhaust fuel addition injector assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR (for DPF)>REMOVAL).


When DTC P20D5 is output:

·

Replace the exhaust fuel addition injector assembly (for bank 2) (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR (for DPF)>REMOVAL).



NEXT

5.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
5.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
a.

Clean the fuel filter case and replace the fuel filter.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.




NEXT

6.PERFORM PM FORCED REGENERATION
6.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

When the exhaust fuel addition injector assembly is replaced, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.


Result:

PM forced regeneration completes normally.




OK

END

NG

7.CHECK FUEL INJECTION SYSTEM
7.CHECK FUEL INJECTION SYSTEM

NEXT

8.CHECK INTAKE / EXHAUST SYSTEM
8.CHECK INTAKE / EXHAUST SYSTEM

NEXT

9.CHECK AFTER TREATMENT CONTROL SYSTEM
9.CHECK AFTER TREATMENT CONTROL SYSTEM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.GO TO DTC CHART

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CHECK AND REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Check for oil leaks and white smoke from the turbocharger sub-assembly (for bank 1 or bank 2) and perform any necessary repairs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>Turbocharger Oil Leak and White Smoke).

HINT:

The cause of the problem may be a malfunction of the turbocharger sub-assembly, but it also may be exhaust valve stem oil leaks.




NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.





NEXT

END