Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0093  Fuel System Leak Detected - Large Leak  


DESCRIPTION

The fuel pressure sensor mounted on the common rail assembly converts the fuel pressure inside the common rail assembly into an electrical signal and outputs the signal to the ECM. The ECM controls the fuel supply pump assembly in order to maintain the fuel pressure inside the common rail assembly at a target pressure calculated by the ECM. Refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

HINT:
·

If the drop in the internal fuel pressure is large when injecting fuel, the ECM interprets this as a fault and stores P0093.

·

If P0093 is present, refer to "Diagnostic Trouble Code (DTC) Table for Common Rail System" (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).



P0093
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After idling for 60 seconds, run engine at 2500 rpm for 30 seconds.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)
Repeat procedures (*A) and (*B) 5 times.
Fuel pressure drop before and after fuel injection is larger than the threshold a certain number of times (0.2 seconds or more).
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Suction control valve (fuel supply pump assembly)

·

Injector assembly

·

Pressure discharge valve (common rail assembly (for bank 2))

·

Pressure limiter (common rail assembly (for bank 2))

·

Fuel pressure sensor (common rail assembly (for bank 1))

·

Crankshaft position sensor

·

Fuel filter element sub-assembly

·

Open or short in No. 1 or No. 2 injector driver circuit (P062D, P062E stored simultaneously)

·

Open or short in injector assembly circuit

·

No. 1 or No. 2 injector driver (P062D, P062E stored simultaneously)

·

ECM



Related Data List
DTC No. Data List
P0093
·

Common Rail Pressure

·

Target Common Rail Pressure



HINT:

When DTC P0093 is set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Engine and ECT / Data List / Common Rail Pressure.

Reference:
Engine Speed Common Rail Pressure
Idling Approximately 27000 to 49000 kPa
3000 rpm (No engine load) Approximately 57000 to 77000 kPa


MONITOR DESCRIPTION

P0093 (Fuel leaks in high-pressure areas):

This DTC indicates that fuel leaks exist in high pressure areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail assembly after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is large when injecting fuel.

In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump assembly, common rail assembly, injector assemblies and piping. The ECM adjusts the suction control valve opening angle to obtain the target internal fuel pressure.

If this DTC is stored, the ECM enters fail-safe mode. In fail-safe mode, both fuel injection and fuel supply pump assembly operation are suspended, and then the engine is stopped. Before the engine is stopped, the ECM permits the vehicle to be driven for 1 minute. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


MONITOR STRATEGY

Required sensors Fuel pressure sensor
Frequency of operation Continuous
Duration 1 second
MIL operation 1 driving cycle

CAUTION / NOTICE / HINT

NOTICE:
·

Soon after starting the engine, visually check for fuel leaks in the fuel line.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


A384556E01
2.656,4.344 2.125,6.667 true 5.01,6.375 4.927,6.635 false 0.115,0.115 5,0.323 4.885,0.208 10 false DTC P0093 stored due to a temporary stuck open malfunction of injector No. 3 0.615,6.708 2.917,7.083 2.302,0.375 10 false Injection Feedback Val #3 is stuck at the maximum value of 5.0 mm3/st 4.188,6.656 5.76,7.021 1.573,0.365 10 false Data set 4 was recorded when P0093 was stored

HINT:
·

The following can be deduced from the above freeze frame data:

-

The common rail fuel pressure dropped suddenly when the engine was being run at a moderate engine speed during engine warmup and DTC P0093 was stored at the point when data set 4 was recorded.

-

Injection Feedback Val #3 is 5.0 mm3/st which is large (the normal value is between -3.0 and 3.0 mm3/st) and indicates that the injector assembly of cylinder 3 may be malfunctioning.


·

Actual cause: In this case, foreign matter in the fuel is stuck inside an injector assembly causing the injector assembly to malfunction temporarily.

In order to remove the foreign matter in the fuel (the main cause of the problem), the fuel filter case needs to be cleaned and the fuel filter needs to be replaced.



A206075E34
3.823,4.208 3.448,3.573 false 3.823,4.208 3.448,4.625 false 0.125,0.938 1.469,1.135 1.344,0.198 10 false Engine Speed (rpm) 0.125,2.458 2.052,2.667 1.927,0.208 10 false Common Rail Pressure (kPa) 0.125,4.125 2.417,4.323 2.292,0.198 10 false Target Common Rail Pressure (kPa) 0.125,5.688 1.76,5.885 1.635,0.198 10 false Injection Volume (mm3/st) 1.344,2.198 1.469,2.365 0.125,0.167 10 false 0 1.115,1.75 1.469,1.917 0.354,0.167 10 false 1000 1.125,1.302 1.469,1.458 0.344,0.156 10 false 2000 1.323,3.792 1.427,3.979 0.104,0.188 10 false 0 1.021,3.333 1.427,3.49 0.406,0.156 10 false 32500 1.01,2.885 1.427,3.052 0.417,0.167 10 false 65000 1.323,5.344 1.427,5.531 0.104,0.188 10 false 0 1.01,4.885 1.417,5.042 0.406,0.156 10 false 35000 1,4.438 1.417,4.604 0.417,0.167 10 false 70000 1.333,6.948 1.438,7.135 0.104,0.188 10 false 0 1.063,6.5 1.427,6.656 0.365,0.156 10 false 60.00 0.979,6.052 1.427,6.219 0.448,0.167 10 false 120.00 0.104,0.073 4.313,0.25 4.208,0.177 10 false This is snapshot data which was taken when P0093 was stored (1): 3.396,3.938 3.542,4.125 0.146,0.188 10 false A 3.375,2.365 3.521,2.552 0.146,0.188 10 false A 3.396,7.083 3.542,7.271 0.146,0.188 10 false A 3.396,5.51 3.542,5.698 0.146,0.188 10 false A 3.885,4.156 4.083,4.354 0.198,0.198 10 false *1 0.104,0.417 6.427,0.604 6.323,0.188 10 false DTC P0093 was stored due to a decrease in fuel pressure when the accelerator pedal was depressed 2.583,7.083 2.771,7.271 0.188,0.188 10 false A'

A206076E01
1.332,2.197 1.434,2.380 0.101,0.183 10 0 1.026,1.74 1.431,1.895 0.405,0.156 10 50.00 0.96,1.291 1.430,1.456 0.471,0.165 10 100.00 1.066,3.804 1.431,3.986 0.365,0.183 10 -10.0 1.32,3.346 1.434,3.502 0.113,0.156 10 0 1.128,2.898 1.432,3.063 0.304,0.165 10 10.0 0.231,0.829 1.512,1.026 1.281,0.198 10 Accel Position (%) 0.231,2.547 2.463,2.689 2.232,0.142 10 Injection Feedback Val #3 (mm3/st) 0.077,0.072 4.320,0.284 4.243,0.211 10 This is snapshot data which was taken when P0093 was stored (2): 1.141,5.34 1.441,5.523 0.300,0.183 10 OFF 1.189,4.995 1.442,5.151 0.252,0.156 10 ON 0.208,4.154 0.514,4.296 0.306,0.142 10 MIL 3.373,3.938 3.507,4.121 0.133,0.183 10 A 3.383,2.322 3.516,2.505 0.133,0.183 10 A 3.387,5.476 3.521,5.658 0.133,0.183 10 A 4.504,4.16 4.723,4.316 0.218,0.156 10 *2 4.585,4.156 4.098,3.202 false 0.077,0.417 6.418,0.601 6.341,0.184 10 DTC P0093 was stored due to a decrease in fuel pressure when the accelerator pedal was depressed

HINT:

*1: Fuel press suddenly decreases for a moment, and then recovers. This can be seen clearly by comparing it to target common rail pressure.

*2: Injection feedback Val #3 is 5.0 mm3/st which is large (the normal value is between -3.0 and 3.0 mm3/st) and indicates that the injector assembly of cylinder 3 may be malfunctioning.


Reference Values for DTC P0093 Storage Point (Point A)
Data List Value Unit
Engine Speed 1478 rpm
Fuel Press 8900 kPa
Target Common Rail Pressure 65320 kPa
Injection Volume (Point A) 51.26 mm3/st
Injection Volume (Point A`) 9.76 mm3/st
Accel Position 63.67 %
Injection Feedback Val #1 -1.1 mm3/st
Injection Feedback Val #2 -2.5 mm3/st
Injection Feedback Val #3 5.0 mm3/st
Injection Feedback Val #4 -1.8 mm3/st
MIL ON -

PROCEDURE

1.CHECK FOR FUEL LEAKS (IN HIGH-PRESSURE AREAS)
a.

Before starting the engine, visually check for fuel leaks from the fuel supply pump assembly, injector assembly, common rail assembly, and the fuel pipes in high-pressure areas.

OK:

No fuel leaks in high-pressure areas.




OK

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0093) AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)

NG

REPAIR FUEL LEAK POINT

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0093) AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.


d.

Read the DTCs and freeze frame data.

Result
Result Proceed to
P0093 and "P0190, P0192 and/or P0193" are output C
P0093 and "P0335, P0339 and/or P0340" are output B
Except above A



A

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)

B

GO TO CRANKSHAFT POSITION SENSOR "A" CIRCUIT

C

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
a.

Check if the fuel level is low.

Result
Result Proceed to
The indicator (fuel warning light) is illuminated A
The indicator (fuel warning light) is not illuminated B



A

4.ADD FUEL

B

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #8)
4.ADD FUEL
a.

Add fuel.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.
A223284

Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

NOTICE:
·

Hand pump pumping speed: Max. 2 strokes/sec.

·

The hand pump must be pushed with a full stroke during pumping.

·

When the fuel pressure at the fuel supply pump assembly inlet port reaches a saturated pressure, the hand pump resistance increases.

·

If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.

·

If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter element sub-assembly, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

·

If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.




b.

Start the engine.

NOTICE:
·

If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.

·

Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

·

Use a fully-charged battery.



i.

When the engine can be started, proceed to the next step.


ii.

If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.



c.

Turn the ignition switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON and turn the GTS on.



g.

Start the engine. (*A)


h.

Enter the following menus: Engine and ECT / Active Test / Test the Fuel Leak. (*B)


i.

Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)


j.

Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)

A192848E03
0.177,1.313 1.583,1.583 1.406,0.271 10 false Active Test Operation 6.5,2.313 6.896,2.49 0.396,0.177 10 false Time 1.677,0.969 2.042,1.167 0.365,0.198 10 false ON 1.646,1.625 2.073,1.823 0.427,0.198 10 false OFF 2.563,1.927 3.375,2.094 0.813,0.167 10 false 10 seconds 3.188,0.656 4,0.823 0.813,0.167 10 false 10 seconds 2.635,0.24 3.229,0.417 0.594,0.177 10 false 1st time 3.896,0.24 4.5,0.427 0.604,0.188 10 false 2nd time 5.198,0.24 5.792,0.406 0.594,0.167 10 false 5th time 5.99,1.865 6.75,2.083 0.76,0.219 10 false 3 minutes


k.

Enter the following menus: Engine and ECT / Trouble Codes.


l.

Read Current DTCs.

i.

When no DTCs are output, the air bleeding is completed.


ii.

If any DTCs are output, proceed to the next step.



m.

Repeat steps (*A) to (*D).



o.

Start the engine and warm it up.


p.

Confirm that the shift lever is in neutral and securely apply the parking brake.


q.

Fully depress the accelerator pedal for 5 seconds, and then release it. (*E)


r.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*F)


s.

Repeat procedures (*E) and (*F) 5 times.

A220593E04
1.631,1.808 2.016,1.984 0.385,0.177 10 5000 1.47,0.54 1.965,0.717 0.495,0.177 10 160000 5.134,2.085 5.771,2.262 0.637,0.177 10 3000 rpm 1.868,2.501 1.996,2.678 0.128,0.177 10 0 1.858,1.171 1.986,1.347 0.128,0.177 10 0 0.058,0.778 1.545,0.948 1.487,0.170 10 Common Rail Pressure 0.058,2.12 1.012,2.290 0.955,0.170 10 Engine Speed 0.058,3.388 1.228,3.558 1.170,0.170 10 Accelerator Pedal 0.944,3.043 2.106,3.235 1.162,0.193 10 Fully Depressed 1.022,3.687 2.002,3.880 0.980,0.193 10 Fully Released 2.855,4.175 3.552,4.365 0.698,0.191 10 5 seconds 6.453,4.089 6.856,4.280 0.403,0.191 10 Time 3.102,2.914 3.724,3.150 0.622,0.236 10 Step (*E) 6.212,2.914 6.810,3.150 0.598,0.236 10 Step (*E) 4.75,2.914 5.376,3.150 0.626,0.236 10 Step (*F) 2.101,0.529 2.370,0.719 0.268,0.190 10 kPa 2.078,1.718 2.393,1.879 0.315,0.162 10 rpm


t.

Enter the following menus: Engine and ECT / Trouble Codes.


u.

Read Current DTCs.

Result
Result Proceed to
DTC is output A
No DTC is output B



A

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #8)

B

DTC CAUSED BY RUNNING OUT OF FUEL

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #8)
a.

Read the value of Injection Feedback Val #1 to #8 in the freeze frame data recorded in Procedure 2.

Result
Result Proceed to
Injection Feedback Val for at least one cylinder is 5 mm3/st in at least 1 set of freeze frame data B
Except above A

HINT:

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.




A

7.READ VALUE USING GTS (COMMON RAIL PRESSURE)

B

10.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
7.READ VALUE USING GTS (COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Enter the following menus: Engine and ECT / Data List / Common Rail Pressure.


e.

Start the engine.


f.

Read the value of Common Rail Pressure while cranking and idling the engine.

Result
Result Proceed to
The engine cannot be started or the engine can be started but Common Rail Pressure is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON B
Except above A



A

8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8)

B

14.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Engine and ECT / Data List / Injection Feedback Val #1 to #8.


e.

Read the values.

Standard:
GTS Display Engine Condition* Normal Value
Injection Feedback Val #1 to #8 Idling -3.0 mm3/st to 3.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 70°C (158°F) or higher and the engine should be idled for 1 minute or more.


Result
Result Proceed to
Injection Feedback Val for at least one cylinder is more than 3 mm3/st and engine vibration is abnormally large B
Except above A

HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

9.CHECK ENGINE SPEED

B

10.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
9.CHECK ENGINE SPEED
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat procedure *1 5 times.

Result
Result Proceed to
No problems such as sluggishness or variations in the tachometer reading A
Except above B



A

10.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER

B

18.READ VALUE USING GTS (ENGINE SPEED)
10.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
a.

Clean the fuel filter case and replace the fuel filter.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.




NEXT

11.BLEED AIR FROM FUEL SYSTEM
11.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.




NEXT

12.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
12.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure, Target Common Rail Pressure and Target Pump SCV Current.


d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DATA LIST / ACTIVE TEST).

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E58
3.604,2.427 3.719,1.948 3.719,1.948 3.792,1.948 false 4.604,2.594 4.948,2.333 4.948,2.333 5,2.333 false 3.521,2.542 3.24,1.896 3.24,1.896 3.188,1.896 false 3.573,3.24 3.813,4.302 3.813,4.302 3.938,4.302 false 0.083,1.417 1.448,1.573 1.365,0.156 10 false Active Test Operation 0.083,0.583 1.479,0.781 1.396,0.198 10 false Engine Speed (rpm) 0.083,3.25 1.677,3.49 1.594,0.24 10 false Common Rail Pressure 3.813,1.865 5.75,2.031 1.938,0.167 10 false Target Common Rail Pressure 6.469,4.125 6.865,4.302 0.396,0.177 10 false Time 2.125,2.406 2.865,2.771 0.74,0.365 10 false Less than 10000 kPa 3,4.26 3.688,4.427 0.688,0.167 10 false 2 seconds 5.052,2.208 6.281,2.604 1.229,0.396 10 false Abnormal Common Rail Pressure 2.448,1.115 3.125,1.313 0.677,0.198 10 false Test Start 4.177,1.115 4.844,1.313 0.667,0.198 10 false Test Stop 5.625,1.115 6.302,1.313 0.677,0.198 10 false Test Start 2.083,1.813 3.229,2.135 1.146,0.323 10 false Normal Common Rail Pressure 1.646,0.271 2.021,0.438 0.375,0.167 10 false 2000 1.885,0.833 2.052,1 0.167,0.167 10 false 0 1.75,1.302 2.073,1.469 0.323,0.167 10 false ON 1.698,1.552 2.021,1.719 0.323,0.167 10 false OFF 4.01,4.24 6.323,4.583 2.313,0.344 10 false Pressure Discharge Valve Abnormal Common Rail Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Common Rail Pressure" is the actual fuel pressure.



Result
Result Proceed to
The difference between the target common rail pressure and the actual common rail pressure 2 seconds after the Active Test starts is less than 10000 kPa A
Except above B



A

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)

B

14.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
13.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut / #1 to #8.


d.

Check the 8 cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.

HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.





NEXT

15.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
14.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug for all the cylinders (See page Engine / Hybrid System>1VD-FTV (STARTING)>GLOW PLUG>REMOVAL).


b.

Visually check if there is fuel on the glow plugs.

HINT:
·

If there is fuel on a glow plug assembly, fuel may be leaking from an injector assembly.

·

After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa (51.0 kgf/cm2, 725 psi) of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug assembly, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.






NEXT

15.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
15.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL).

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.





NEXT

16.BLEED AIR FROM FUEL SYSTEM
16.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.




NEXT

17.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
17.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation code (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).


b.

Perform the injector pilot quantity learning (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



NEXT

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
18.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Engine Speed.


d.

Read the value while cranking and idling the engine.

Standard:
GTS Display Engine Condition Specified Condition
Engine Speed Cranking 50 to 400 rpm
Idling with warm engine 550 to 650 rpm


HINT:

The value should be the same as the actual engine speed and displayed with no interruption on the GTS.




OK

19.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)

NG

22.REPLACE CRANKSHAFT POSITION SENSOR
19.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)
HINT:

If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).


A275092E02
1.448,1.427 0.865,2.646 0.865,2.646 0.75,2.646 false 1.979,1.094 2.552,0.531 2.552,0.531 2.635,0.531 false 0.094,0.083 0.292,0.25 0.198,0.167 10 false *a 1.208,0.292 1.448,0.49 0.24,0.198 10 false *1 0.521,2.552 0.76,2.75 0.24,0.198 10 false *2 2.708,0.427 2.948,0.625 0.24,0.198 10 false *3 3.76,1.354 4,1.563 0.24,0.208 10 false *4 5.802,1.115 6.042,1.313 0.24,0.198 10 false *5

Text in Illustration
*1 Engine *2 Engine Wire
*3 Common Rail Assembly (for Bank 1)
(Fuel Pressure Sensor)
*4 Wire to Wire
*5 ECM - -
*a Vibration Method (Reference) - -

a.

Check if the MIL lights up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.

Result:
Result Proceed to
MIL does not come on A
MIL comes on B




A

20.INSPECT FUEL TEMPERATURE SENSOR (SENSOR OUTPUT)

B

23.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
20.INSPECT FUEL TEMPERATURE SENSOR (SENSOR OUTPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Fuel Temperature.


d.

Read the value.

OK:

The value is almost the same as the actual fuel temperature.


HINT:
·

When the engine is stopped and left overnight, the fuel temperature becomes the same as the ambient temperature.

·

If there is a problem with the fuel temperature sensor, and a fuel temperature value lower than the actual fuel temperature is indicated, P0093 may be stored.





OK

21.CHECK FOR INTERMITTENT PROBLEMS

NG

27.REPLACE FUEL TEMPERATURE SENSOR
21.CHECK FOR INTERMITTENT PROBLEMS

NEXT

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
22.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL).

HINT:

Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.




NEXT

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
23.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
a.

Repair or replace the harness or connector.



NEXT

24.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)
24.CHECK WIRE HARNESS (FUEL PRESSURE SENSOR AND ECM)
HINT:

If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).


A275092E02
1.448,1.427 0.865,2.646 0.865,2.646 0.75,2.646 false 1.979,1.094 2.552,0.531 2.552,0.531 2.635,0.531 false 0.094,0.083 0.292,0.25 0.198,0.167 10 false *a 1.208,0.292 1.448,0.49 0.24,0.198 10 false *1 0.521,2.552 0.76,2.75 0.24,0.198 10 false *2 2.708,0.427 2.948,0.625 0.24,0.198 10 false *3 3.76,1.354 4,1.563 0.24,0.208 10 false *4 5.802,1.115 6.042,1.313 0.24,0.198 10 false *5

Text in Illustration
*1 Engine *2 Engine Wire
*3 Common Rail Assembly (for Bank 1)
(Fuel Pressure Sensor)
*4 Wire to Wire
*5 ECM - -
*a Vibration Method (Reference) - -

a.

Check if the MIL lights up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.

Result:
Result Proceed to
MIL does not come on A
MIL comes on B




A

25.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 1) (FUEL PRESSURE SENSOR)

B

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
25.REPLACE COMMON RAIL ASSEMBLY (FOR BANK 1) (FUEL PRESSURE SENSOR)
a.

Replace the common rail assembly (for bank 1) (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>REMOVAL).

HINT:

Before replacing the common rail assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.




NEXT

26.BLEED AIR FROM FUEL SYSTEM
26.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.




NEXT

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
27.REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL TEMPERATURE SENSOR>REMOVAL).

HINT:

Before replacing the fuel temperature sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.




NEXT

28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
28.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.



e.

Start the engine.


f.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).


g.

Confirm that the shift lever is in neutral and securely apply the parking brake.


h.

Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)


i.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)


j.

Repeat procedures (*A) and (*B) 5 times.

A220593E04
1.631,1.808 2.016,1.984 0.385,0.177 10 5000 1.47,0.54 1.965,0.717 0.495,0.177 10 160000 5.134,2.085 5.771,2.262 0.637,0.177 10 3000 rpm 1.868,2.501 1.996,2.678 0.128,0.177 10 0 1.858,1.171 1.986,1.347 0.128,0.177 10 0 0.058,0.778 1.545,0.948 1.487,0.170 10 Common Rail Pressure 0.058,2.12 1.012,2.290 0.955,0.170 10 Engine Speed 0.058,3.388 1.228,3.558 1.170,0.170 10 Accelerator Pedal 0.944,3.043 2.106,3.235 1.162,0.193 10 Fully Depressed 1.022,3.687 2.002,3.880 0.980,0.193 10 Fully Released 2.855,4.175 3.552,4.365 0.698,0.191 10 5 seconds 6.453,4.089 6.856,4.280 0.403,0.191 10 Time 3.102,2.914 3.724,3.150 0.622,0.236 10 Step (*E) 6.212,2.914 6.810,3.150 0.598,0.236 10 Step (*E) 4.75,2.914 5.376,3.150 0.626,0.236 10 Step (*F) 2.101,0.529 2.370,0.719 0.268,0.190 10 kPa 2.078,1.718 2.393,1.879 0.315,0.162 10 rpm


k.

Enter the following menus: Engine and ECT / Trouble Codes.


l.

Read the DTCs.

OK:

No DTCs are output.




NEXT

END