Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › from 2015.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

IG Circuit


-

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART).

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS).

·

Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or main body ECU (multiplex network body ECU), refer to the entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check for DTCs.

Result
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COWL SIDE JUNCTION BLOCK LH)

B

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COWL SIDE JUNCTION BLOCK LH)
a.

Disconnect the E128 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the 2I and 2J connectors from the connector from the cowl side junction block LH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E128-3 (IG1D) - 2I-18 Always Below 1 Ω
2J-1 - Body ground
E128-3 (IG1D) and 2I-18 - Body ground 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - INTEGRATION RELAY (IG2 MAIN RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - INTEGRATION RELAY (IG2 MAIN RELAY))
a.

Disconnect the 2H connector from the cowl side junction block LH.


b.

Disconnect the 1R and 1S connectors from the integration relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2H-18 - 1R-2 Always Below 1 Ω
1S-4 - Body ground
2H-18 and 1R-2 - Body ground 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - IG1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK LH - IG1 RELAY)
a.

Disconnect the 2H connector from the cowl side junction block LH.


b.

Remove the IG1 relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2H-17 - 1 (IG1 relay) Always Below 1 Ω
2 (IG1 relay) - Body ground
2H-17 and 1 (IG1 relay) - Body ground 10 kΩ or higher




OK

5.INSPECT INTEGRATION RELAY (IG2-MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INTEGRATION RELAY (IG2-MAIN RELAY)
a.

Remove the integration relay.


b.

Measure the resistance according to the value(s) in the table below.

U165700E01
1.595,0.092 1.905,0.230 0.310,0.139 10 1P 3.601,0.075 3.911,0.214 0.310,0.139 10 1R 4.418,0.085 4.728,0.223 0.310,0.139 10 1S 5.358,0.06 5.619,0.198 0.262,0.139 10 1X 0.113,0.032 0.424,0.171 0.310,0.139 10 *1 5.948,0.051 6.210,0.190 0.262,0.139 10 1Y 5.654,0 5.882,0.184 0.229,0.184 10 *A 6.26,0 6.488,0.184 0.229,0.184 10 *B

Text in Illustration
*A for RHD *B for LHD
*1 Integration Relay (IG2 MAIN Relay) - -

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
1X-1 - 1P-7 Battery voltage not applied to terminals 1R-2 and 1S-4 10 kΩ or higher
Battery voltage applied to terminals 1R-2 and 1S-4 Below 1 Ω

for LHD:
Tester Connection Condition Specified Condition
1Y-1 - 1P-7 Battery voltage not applied to terminals 1R-2 and 1S-4 10 kΩ or higher
Battery voltage applied to terminals 1R-2 and 1S-4 Below 1 Ω




OK

6.INSPECT IG1 RELAY

NG

REPLACE INTEGRATION RELAY (IG2 MAIN RELAY)

6.INSPECT IG1 RELAY
a.

Remove the IG1 relay.


b.
A092673E80
1.573,1.115 2.042,1.115 true 2.677,0.448 2.344,0.781 true 2.667,1.115 3.135,1.115 true 2.354,1.427 2.094,1.74 true

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 2 and 1 10 kΩ or higher
Battery voltage applied to terminals 2 and 1 Below 1 Ω


Text in Illustration
*1 IG1 Relay



OK

7.INSPECT COWL SIDE JUNCTION BLOCK LH (IG1 NO. 1,IG1 NO. 2, IG1 NO. 3 RELAY)

NG

REPLACE IG1 RELAY

7.INSPECT COWL SIDE JUNCTION BLOCK LH (IG1 NO. 1,IG1 NO. 2, IG1 NO. 3 RELAY)

b.

Measure the resistance according to the value(s) in the table below.

U156538E01
0.344,0.057 0.529,0.215 0.186,0.158 10 *a 3.148,1.964 3.562,2.123 0.413,0.158 10 2J 5.46,0.666 5.873,0.824 0.413,0.158 10 2I 5.796,1.992 6.209,2.151 0.413,0.158 10 2G

Text in Illustration
*a Component without harness connected
(Cowl Side Junction Block LH)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
2G-1 - 2I-19 Battery voltage not applied to terminals 2I-18 and 2J-1 10 kΩ or higher
Battery voltage applied to terminals 2I-18 and 2J-1 Below 1 Ω
2G-1 - 2I-33 Battery voltage not applied to terminals 2I-18 and 2J-1 10 kΩ or higher
Battery voltage applied to terminals 2I-18 and 2J-1 Below 1 Ω
2G-1 - 2I-11 Battery voltage not applied to terminals 2I-18 and 2J-1 10 kΩ or higher
Battery voltage applied to terminals 2I-18 and 2J-1 Below 1 Ω



Result
Result Proceed to
OK A
NG for LHD B
for RHD C


A

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.


U165441E01
0.078,0.031 0.266,0.189 0.189,0.158 10 *a 0.612,1.707 1.109,1.865 0.497,0.158 10 IG1D 1.242,0.899 1.151,1.796 1.151,1.796 1.016,1.796 false 1.481,0.126 1.894,0.284 0.413,0.158 10 E128

Standard Voltage:
Tester Connection Condition Specified Condition
E128-3 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher


Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)