Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.08–2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the ignition switch is first turned to ON, the MIL should be illuminated and should turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A385644E02
2.031,0.865 2.646,1.063 0.615,0.198 10 false CANH 2.042,1.573 2.656,1.771 0.615,0.198 10 false CANL 2.521,0.708 3.167,0.958 0.646,0.25 10 false 39 2.521,1.375 3.167,1.625 0.646,0.25 10 false 40 4.521,0.729 5.167,0.979 0.646,0.25 10 false 10 4.51,1.417 5.156,1.667 0.646,0.25 10 false 11 4.781,0.875 5.396,1.073 0.615,0.198 10 false CANH 4.771,1.604 5.385,1.802 0.615,0.198 10 false CANL 0.781,2.104 1.396,2.302 0.615,0.198 10 false E199 0.781,2.281 3.052,2.583 2.271,0.302 10 false Combination Meter Assembly 5.177,2.104 6.083,2.302 0.906,0.198 10 false A38*1, A52*2 5.177,2.292 6.083,2.49 0.906,0.198 10 false ECM 0.969,3.417 3.24,3.719 2.271,0.302 10 false : CAN Communication Line 4.042,2.781 4.833,3.219 0.792,0.438 10 false *1: for LHD *2: for RHD

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Check the illumination condition of the MIL.

Result
MIL Condition Proceed to
Illuminates → Turns off Ignition switch ON → After engine is started A
Other than above - B



A

B

2.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.


Result:
Result Proceed to
Communication is possible A
Communication is not possible B




A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check if any DTCs have been detected. Note down any DTCs.

Result:
Result Proceed to
DTCs are not output A
Any DTCs is output B




A

4.PERFORM ACTIVE TEST USING GTS

B

4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.


e.

Check the status of the MIL while performing the Active Test.

Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY