Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of this pulse signal.

A115899E20
0.43,1.047 1.579,1.425 1.149,0.378 10 from Wheel Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.722,1.96 5.142,2.123 1.420,0.163 10 Combination Meter 2.976,0.599 3.784,0.776 0.809,0.177 10 Pulse Signal 4.902,0.599 5.711,0.776 0.809,0.177 10 Pulse Signal 6.045,1.324 6.492,1.486 0.448,0.163 10 ECM

DTC No. DTC Detection Condition Trouble Area
P0500 While the vehicle is being driven, no vehicle speed signal is transmitted to the ECM (2 trip detection logic).
·

Open or short in speed signal circuit

·

Wheel speed sensor

·

Combination meter assembly

·

ECM

·

Skid control ECU



MONITOR DESCRIPTION

Automatic Transaxle Models:

The ECM assumes that the vehicle is being driven when the vehicle speed signal from the transmission (SP2) indicates a speed of 9 km/h (6 mph) or more.

If there is no vehicle speed signal from the combination meter (SP1) for 5 seconds when the vehicle is being driven, the ECM determines this to be a malfunction of the vehicle speed sensor. The ECM then illuminates the MIL and stores the DTC.


Manual Transaxle Models:

The ECM assumes that the vehicle is being driven when the idle fuel-cut operation* is being executed. If there is no signal from the vehicle speed sensor despite this condition being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

*: Idle fuel-cut is executed when the throttle valve is fully closed and engine speed is over 2500 rpm.


WIRING DIAGRAM

A237393E07
0.548,2.163 1.718,2.327 1.170,0.164 10 Skid Control ECU 0.548,2.024 0.827,2.185 0.279,0.161 10 A24 2.523,2.135 2.802,2.296 0.279,0.161 10 E7 2.523,2.286 3.732,2.461 1.209,0.175 10 Combination Meter 2.426,1.343 2.582,1.524 0.156,0.181 10 SI 3.61,1.249 3.801,1.430 0.191,0.181 10 +S 5.462,2.139 6.356,2.299 0.894,0.160 10 A38*1, A52*2 5.462,2.3 5.828,2.467 0.367,0.167 10 ECM 5.218,1.181 5.520,1.362 0.303,0.181 10 SPD 5.976,0.872 6.280,1.032 0.304,0.160 10 5 V 4.975,1.264 5.186,1.406 0.211,0.142 10 13 3.917,1.249 4.052,1.422 0.135,0.173 10 4 2.23,1.343 2.357,1.516 0.127,0.173 10 3 1.635,1.343 1.822,1.502 0.187,0.159 10 12 1.257,1.431 1.545,1.583 0.288,0.153 10 SP1 4.738,2.973 5.682,3.139 0.944,0.166 10 to Other ECUs 6.384,2.787 7.137,3.110 0.753,0.323 10 *1: for LHD *2: for RHD

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction.





OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speeds displayed on the GTS and speedometer display are equal.




OK

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E7-4 (+S) - A38-13 (SPD) Always Below 1 Ω
E7-4 (+S) or A38-13 (SPD) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E7-4 (+S) - A52-13 (SPD) Always Below 1 Ω
E7-4 (+S) or A52-13 (SPD) - Body ground Always 10 kΩ or higher


HINT:

If the wire harness has a short, check the speed signal circuit in other systems related to the vehicle speed signal (e.g. tire pressure warning system, audio system, etc.).




OK

4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)

NG

CHECK ALL SYSTEMS RELATED TO SPEED SENSOR SIGNAL AND REPAIR OR REPLACE MALFUNCTIONING HARNESS OR CONNECTOR

4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
U165842E01
1.572,2.035 1.783,2.195 0.211,0.161 10 E7 2.103,2.704 1.746,3.166 false 1.526,3.141 1.728,3.297 0.202,0.156 10 +S 0.16,0.198 0.381,0.381 0.221,0.184 10 *a

a.

Disconnect the combination meter assembly connector.

HINT:

Disconnect the ECU connectors of other systems related to the speed signal, but do not disconnect the ECM connectors.



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-4 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

5.CHECK COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM)

NG

5.CHECK COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM)
A385472E01
1.49,1.229 1.969,1.49 true 0.063,0.073 0.396,0.323 0.333,0.25 10 false *a 0.323,0.729 0.656,0.979 0.333,0.25 10 false E7 2.031,1.469 2.365,1.719 0.333,0.25 10 false +S 0.104,2.771 1.156,3.063 1.052,0.292 10 false 5 to 12 V 0.458,4.26 0.75,4.531 0.292,0.271 10 false 0V 1.49,4.281 2.885,4.563 1.396,0.281 10 false Turn Wheel

a.

Remove the combination meter assembly.


b.

Connect the combination meter assembly connector.


c.

Move the shift lever to N.


d.

Jack up the vehicle.


e.

Turn the ignition switch to ON.


f.

Check the voltage between the terminal of the combination meter assembly and body ground while the wheels are turned slowly.

Standard Voltage:
Tester Connection Condition Specified Condition
E7-4 (+S) - Body ground Ignition switch ON
(Wheels turned slowly)
Voltage generated intermittently


HINT:
·

The output voltage fluctuates up and down, similarly to the diagram, when the wheels are turned slowly.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.



Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)



OK

NG

6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
A385472E02
1.573,1.229 2.042,1.438 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.323,0.729 0.635,0.927 0.313,0.198 10 false E7 2.073,1.385 2.385,1.583 0.313,0.198 10 false SI 0.25,2.844 0.76,3.073 0.51,0.229 10 false 12 V 0.365,4.26 0.875,4.49 0.51,0.229 10 false 0V 1.49,4.271 2.615,4.594 1.125,0.323 10 false Turn Wheel

a.

Remove the combination meter assembly.


b.

Connect the combination meter assembly connector.


c.

Move the shift lever to N.


d.

Jack up the vehicle.


e.

Turn the ignition switch to ON.


f.

Check the voltage between the terminal of the combination meter assembly and body ground while the wheels are turned slowly.

Standard Voltage:
Tester Connection Condition Specified Condition
E7-3 (SI) - Body ground Ignition switch ON
(Wheels turned slowly)
Voltage generated intermittently


HINT:

The output voltage fluctuates up and down, similarly to the diagram, when the wheels are turned slowly.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)



OK

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VSC ACTUATOR WITH ACTUATOR BRACKET ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VSC ACTUATOR WITH ACTUATOR BRACKET ASSEMBLY)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the VSC actuator with actuator bracket assembly connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E7-3 (SI) - A24-12 (SP1) Always Below 1 Ω
E7-3 (SI) or A24-12 (SP1) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR