Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.08–2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 When conditions (a), (b) and (c) are met, a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.4 mph) or more.

(b) The engine speed is 1000 rpm or more.

(c) The STA signal is ON.


·

Park/Neutral Position (PNP) switch

·

Clutch start switch

·

ST relay circuit

·

ECM



WIRING DIAGRAM

A351214E08
5.677,1.031 6.135,1.229 0.458,0.198 10 false NEO 1.292,1.594 1.75,1.75 0.458,0.156 10 false STAR 1.365,2.104 1.823,2.292 0.458,0.188 10 false STA 1.458,1.073 1.823,1.25 0.365,0.177 10 false NE 0.313,2.802 2.188,3.083 1.875,0.281 10 false Smart Key ECU Assembly 3.333,2.563 5.208,2.76 1.875,0.198 10 false Park/Neutral Position Switch 0.604,4.573 0.833,4.729 0.229,0.156 10 false ST 5.698,1.604 6.073,1.781 0.375,0.177 10 false NSW 5.698,3.677 6.01,3.833 0.313,0.156 10 false STA 6.104,4.917 6.458,5.083 0.354,0.167 10 false ECM 3.292,4.615 3.51,4.771 0.219,0.156 10 false ST 2.417,6.135 2.885,6.313 0.469,0.177 10 false Starter 0.75,6.802 1.25,7 0.5,0.198 10 false Battery 5.354,1.063 5.667,1.219 0.313,0.156 10 false C45 5.354,1.594 5.667,1.75 0.313,0.156 10 false C45 5.354,3.781 5.667,3.938 0.313,0.156 10 false A38 5.406,0.875 5.594,1.063 0.188,0.188 10 false 31 5.354,1.385 5.677,1.573 0.323,0.188 10 false 120 5.396,3.594 5.583,3.771 0.188,0.177 10 false 46 2.563,5.031 2.688,5.198 0.125,0.167 10 false 3 3.344,2.385 3.667,2.552 0.323,0.167 10 false C24 2.563,4.146 2.667,4.302 0.104,0.156 10 false 5 3.01,4.146 3.115,4.302 0.104,0.156 10 false 2 1.104,5.74 1.208,5.896 0.104,0.156 10 false 1 1.75,5.5 1.854,5.656 0.104,0.156 10 false 1 3.021,5.021 3.135,5.188 0.115,0.167 10 false 1 1.781,5.688 1.99,5.844 0.208,0.156 10 false D2 1.031,5.927 1.365,6.083 0.333,0.156 10 false D20 3.552,2 3.74,2.188 0.188,0.188 10 false 5 3.771,1.969 3.958,2.156 0.188,0.188 10 false L 1.729,2.031 1.938,2.188 0.208,0.156 10 false 12 1.75,1.479 1.958,1.635 0.208,0.156 10 false 10 1.75,0.958 2.021,1.115 0.271,0.156 10 false 14 4.552,2 4.74,2.188 0.188,0.188 10 false 4 4.333,1.969 4.521,2.156 0.188,0.188 10 false B 0.333,2.635 0.698,2.813 0.365,0.177 10 false E128 0.094,0.021 1.219,0.24 1.125,0.219 12 false for LHD (A/T):

A351214E09
5.677,1.031 6.135,1.229 0.458,0.198 10 false NEO 1.302,1.542 1.76,1.698 0.458,0.156 10 false STAR 1.385,2.052 1.844,2.24 0.458,0.188 10 false STA 1.458,1.01 1.823,1.188 0.365,0.177 10 false NE 0.292,2.75 2.167,3.031 1.875,0.281 10 false Smart Key ECU Assembly 3.49,2.594 4.76,2.771 1.271,0.177 10 false Clutch Start Switch 0.604,4.542 0.833,4.698 0.229,0.156 10 false ST 5.698,1.531 6.073,1.708 0.375,0.177 10 false NSW 5.698,3.635 6.01,3.792 0.313,0.156 10 false STA 6.094,4.917 6.448,5.083 0.354,0.167 10 false ECM 3.281,4.542 3.5,4.698 0.219,0.156 10 false ST 2.417,6.135 2.885,6.313 0.469,0.177 10 false Starter 0.75,6.76 1.25,6.958 0.5,0.198 10 false Battery 5.354,1.052 5.667,1.208 0.313,0.156 10 false C45 5.354,1.583 5.667,1.74 0.313,0.156 10 false C45 5.354,3.781 5.667,3.938 0.313,0.156 10 false A38 5.385,0.865 5.573,1.052 0.188,0.188 10 false 31 5.365,1.375 5.688,1.563 0.323,0.188 10 false 120 5.396,3.604 5.583,3.781 0.188,0.177 10 false 46 2.573,5.042 2.698,5.208 0.125,0.167 10 false 3 3.51,2.448 3.833,2.615 0.323,0.167 10 false A49 2.573,4.115 2.677,4.271 0.104,0.156 10 false 5 3.021,4.115 3.125,4.271 0.104,0.156 10 false 2 1.104,5.698 1.208,5.854 0.104,0.156 10 false 1 1.75,5.458 1.854,5.615 0.104,0.156 10 false 1 2.99,5.031 3.104,5.198 0.115,0.167 10 false 1 1.792,5.688 2,5.844 0.208,0.156 10 false D2 1.031,5.917 1.365,6.073 0.333,0.156 10 false D20 3.552,1.969 3.74,2.156 0.188,0.188 10 false 2 1.76,1.969 1.969,2.125 0.208,0.156 10 false 12 1.76,1.448 1.969,1.604 0.208,0.156 10 false 10 1.76,0.927 2.031,1.083 0.271,0.156 10 false 14 4.552,1.969 4.74,2.156 0.188,0.188 10 false 1 0.292,2.594 0.656,2.771 0.365,0.177 10 false E128 0.094,0.021 3.208,0.26 3.115,0.24 12 false for LHD (M/T) w/ Entry and Start System:

A375090E01
5.955,6.576 6.291,6.732 0.336,0.156 10 ECM 2.956,2.601 4.200,2.785 1.244,0.184 10 Clutch Start Switch 2.956,2.446 3.269,2.611 0.313,0.165 10 A49 3.462,6.873 3.683,7.056 0.221,0.184 10 ST 3.299,0.577 3.639,0.733 0.341,0.156 10 ST2 2.818,0.577 3.125,0.733 0.306,0.156 10 AM2 1.601,0.569 1.949,0.725 0.348,0.156 10 AM2 1.116,8.019 1.578,8.203 0.461,0.184 10 Battery 4.75,7.548 5.226,7.703 0.475,0.156 10 Starter 4.013,7.364 4.290,7.547 0.277,0.184 10 D20 4.351,7.171 4.568,7.326 0.217,0.156 10 D2 4.484,7.005 4.615,7.157 0.132,0.152 10 1 4.09,7.197 4.221,7.349 0.132,0.152 10 1 3.898,2.159 4.017,2.320 0.119,0.161 10 1 3.125,2.156 3.239,2.328 0.114,0.172 10 2 0.92,1.682 1.699,1.856 0.779,0.174 10 J/B LH-B 2.754,1.04 3.046,1.194 0.292,0.154 10 E93 2.754,1.177 3.698,1.351 0.944,0.174 10 Ignition Switch 3.624,0.577 3.743,0.751 0.119,0.174 10 7 2.674,0.577 2.793,0.751 0.119,0.174 10 5 0.078,0.028 3.289,0.281 3.211,0.253 12 for LHD (M/T) w/o Entry and Start System: 5.687,2.264 6.169,2.433 0.482,0.170 10 NSW 5.699,4.292 6.188,4.448 0.489,0.156 10 STA 5.339,2.264 5.675,2.419 0.336,0.156 10 C45 5.338,4.295 5.619,4.451 0.281,0.156 10 A38 5.353,2.078 5.608,2.241 0.254,0.163 10 120 5.395,4.124 5.585,4.273 0.191,0.149 10 46 1.635,4.505 1.856,4.688 0.221,0.184 10 ST 3.118,6.452 3.292,6.598 0.174,0.147 10 5 3.109,6.14 3.251,6.317 0.142,0.177 10 2 3.907,6.452 4.054,6.631 0.147,0.179 10 3 3.907,6.139 4.072,6.299 0.165,0.161 10 1

A375090E02
5.955,6.576 6.291,6.732 0.336,0.156 10 ECM 2.956,2.601 4.200,2.785 1.244,0.184 10 Clutch Start Switch 2.956,2.446 3.269,2.611 0.313,0.165 10 e1 3.462,6.873 3.683,7.056 0.221,0.184 10 ST 3.299,0.577 3.639,0.733 0.341,0.156 10 ST2 2.818,0.577 3.124,0.733 0.306,0.156 10 AM2 1.601,0.569 1.949,0.725 0.348,0.156 10 AM2 1.116,8.019 1.578,8.203 0.461,0.184 10 Battery 4.75,7.548 5.226,7.703 0.475,0.156 10 Starter 4.013,7.364 4.290,7.548 0.277,0.184 10 D14 4.351,7.171 4.568,7.326 0.217,0.156 10 D2 4.484,7.005 4.615,7.157 0.132,0.152 10 1 4.09,7.197 4.221,7.349 0.132,0.152 10 1 3.898,2.159 4.017,2.320 0.119,0.161 10 1 3.125,2.156 3.239,2.328 0.114,0.172 10 2 0.92,1.682 1.699,1.856 0.779,0.174 10 J/B LH-B 2.754,1.04 3.046,1.194 0.292,0.154 10 E93 2.754,1.177 3.698,1.351 0.944,0.174 10 Ignition Switch 3.624,0.577 3.743,0.751 0.119,0.174 10 7 2.674,0.577 2.793,0.751 0.119,0.174 10 5 0.078,0.028 3.289,0.281 3.211,0.253 12 for RHD (M/T): 5.687,2.264 6.169,2.433 0.482,0.170 10 NSW 5.699,4.294 6.070,4.518 0.372,0.224 10 STA 5.339,2.264 5.675,2.419 0.336,0.156 10 C46 5.338,4.295 5.619,4.451 0.281,0.156 10 A52 5.353,2.078 5.608,2.241 0.254,0.163 10 120 5.395,4.124 5.585,4.273 0.191,0.149 10 46 1.635,4.505 1.856,4.688 0.221,0.184 10 ST 3.118,6.452 3.292,6.598 0.174,0.147 10 5 3.109,6.14 3.251,6.317 0.142,0.177 10 2 3.907,6.452 4.054,6.631 0.147,0.179 10 3 3.907,6.139 4.072,6.299 0.165,0.161 10 1

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.

If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.


d.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

Standard:
Ignition Switch Position Starter Signal
ON OFF
START ON


Result
Result Proceed to
OK A
NG (for Automatic transmission) B
NG (for Manual transmission) C



A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

5.INSPECT CLUTCH START SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Drive the vehicle at a vehicle speed of more than 24 km/h (15 mph) for more than 20 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P0617 is output A
No DTC is output B



A

B

END

5.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (for LHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>INSPECTION).


b.

Inspect the clutch start switch assembly (for RHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>INSPECTION).

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)

B

REPLACE CLUTCH START SWITCH ASSEMBLY

C

REPLACE CLUTCH START SWITCH ASSEMBLY

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)

NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Drive the vehicle at a vehicle speed of more than 24 km/h (15 mph) for more than 20 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P0617 is output A
No DTC is output B



A

B

END